Daniel Agar
1ec10bfcc6
boards: disable CONFIG_ARMV7M_LAZYFPU again ( #16573 )
...
- this was causing hard faults on the CUAV Nora and possibly other boards, disabling everywhere until we fully understand the root cause
2021-01-17 22:40:21 -05:00
Daniel Agar
cb74cb8692
boards: enable CONFIG_ARMV7M_LAZYFPU everywhere
2021-01-12 09:04:38 +01:00
Daniel Agar
c60743b306
boards: NuttX increase file name max 32 -> 40
2020-11-08 12:51:59 -05:00
Daniel Agar
233949a377
NuttX upgrade to 10.0.0+ defconfig changes
2020-10-28 14:25:25 -04:00
David Sidrane
f5fca39253
px4_fmu-v4: Updates for NuttX 9.1.0+ External schedule_note
2020-09-16 21:32:04 -04:00
David Sidrane
3457c30ab3
px4_fmu-v4: Updates for NuttX 9.1.0+ External schedule_note
2020-09-16 21:32:04 -04:00
David Sidrane
7a50f00b00
px4_fmu-v4: Updates for NuttX 9.1.0+ External schedule_note
2020-09-16 21:32:04 -04:00
David Sidrane
9986f63321
px4_fmu-v4 Updates for NuttX 9.1.0-
...
px4_fmu-v4: defconfig MMCSD enable multiblock
2020-09-16 21:32:04 -04:00
Daniel Agar
2c3441aa90
boards: reduce CONFIG_NFILE_DESCRIPTORS 15 -> 12
...
- reduced now that calibration uses uORB::Subscription
- can likely be reduced further (perhaps < 8) with additional testing
2020-08-21 10:12:13 -04:00
Daniel Agar
e3d31a881e
boards: NuttX disable posix message queues
2020-07-17 17:00:21 -04:00
Daniel Agar
5e7d2e830d
boards: delete old board.h boilerplate
2020-06-08 19:10:33 -04:00
Daniel Agar
28d2aca699
boards: include all procfs entries on boards that aren't flash constrained
2020-05-01 20:59:57 -04:00
Daniel Agar
8d0c92003a
boards: remove all CONFIG_NXFONTS_DISABLE*
2020-05-01 20:59:57 -04:00
Beat Küng
34c75f2d36
boards: temporarily disable UART TX DMA
...
work-around for https://github.com/PX4/Firmware/issues/14659 .
This can be reverted when fixed properly.
2020-04-27 08:47:46 -04:00
Daniel Agar
66eacd24bc
px4_fmu-v5_stackcheck: update stack sizes and add to Jenkins
...
- increase stack sizes to run cleanly under stackcheck
- this is likely overkill for most boards, but using stackcheck to set our minimum ensures we have a very safe margin on regular builds and it's something we can currently afford
- remove holybro_durandal-v1_stackcheck from test rack (there's only one unit)
2020-04-11 21:16:10 -04:00
Beat Küng
31937c280d
px4/v4: enable tx dma on telem2
2020-04-09 14:59:28 +02:00
Daniel Agar
40b1043e12
NuttX boards minor lpwork and init stack increases
2020-04-02 23:39:17 -04:00
Daniel Agar
15332a7e56
boards: reduce CONFIG_NFILE_DESCRIPTORS 20 -> 15
2020-04-01 16:17:14 -04:00
Daniel Agar
44bec269b0
boards: update all NuttX configs CONFIG_NSH_MAXARGUMENTS 12 -> 15
2020-03-25 17:59:22 -04:00
Daniel Agar
8738c26426
boards: enable NuttX SPI DMA buffers
...
- update to NuttX with stm32f4 and stm32f7 SPI DMA internal buffers
- remove explicit DMA buffer allocations from new IMU drivers
- restore original BOARD_DMA_ALLOC_POOL_SIZE
- decrease SPI DMA thresholds based on fmu-v2/v3/v4/v5 bench testing
2020-03-22 19:24:26 -04:00
Daniel Agar
b73ec18abb
boards: add px4_fmu-v4 and px4_fmu-v5 optimized (-O3) build variants
2020-03-22 17:50:17 -04:00
Daniel Agar
0ce9e113ff
boards: stm32f4/f7 enable SPI_DMATHRESHOLD=32
2020-03-11 22:08:37 -04:00
Beat Küng
179c89b6bd
board configs: extend board_dma_map.h with a table
2020-03-11 22:08:37 -04:00
Daniel Agar
147e37ac88
px4_fmu-v4: cleanup board_dma_map.h
2020-03-11 22:08:37 -04:00
Daniel Agar
505afc6063
boards: increase LPWORKSTACKSIZE 1536 -> 1600
2020-03-10 12:53:01 -04:00
Beat Küng
d74d094940
nuttx configs: disable nuttx timers which are used for PWM output
...
These are not required, and to be consistent we enforce disabling them now.
2020-02-13 03:49:16 -08:00
Matthias Grob
904ab16558
Fix trailing whitespace, EOF newline, indentation
2019-12-09 13:22:19 +01:00
Daniel Agar
709961ec8c
InvenSense ICM20602 and ICM20608-G: new standalone optimized drivers
...
- uses the FIFO and SPI DMA to transfer full raw data (8 kHz gyro, 4 kHz accel)
- new sensor messages for better visibility
- sensor_{accel, gyro}_fifo: full raw data for optional logging and analysis
- sensor_{accel, gyro}_status: metadata, clipping, etc
- currently not enabled by default
2019-12-03 23:21:32 -05:00
Daniel Agar
99aae8b891
NuttX use toolchain math.h and avoid empty drivers/Kconfig
2019-11-16 11:43:42 +01:00
David Sidrane
40a3e47712
px4:fmu-v4 BSP Updated to NuttX 8.1+
2019-11-16 11:43:42 +01:00
David Sidrane
fa79283602
px4/fmu-v4: update nuttx config
2019-11-16 11:43:42 +01:00
Igor Mišić
543a057f80
fmu-v4: add dshot timer config
2019-10-11 08:14:17 +02:00
Daniel Agar
315141873e
NuttX boards reduce CONFIG_MAX_TASKS 64 -> 32 (default)
2019-10-02 19:44:46 -04:00
Hyon Lim
0262a699c1
UVify Core board support and airframes (Draco, Draco-R, IFO) ( #12337 )
...
* also includes minor changes to make it easy to keep in sync with px4_fmu-v4
2019-08-23 17:02:25 -04:00
Daniel Agar
0955fd2d58
NuttX boards reduce CONFIG_NFILE_DESCRIPTORS 54 -> 20
2019-08-07 21:23:27 -04:00
Daniel Agar
5421ef5535
NuttX increase HPWORK and LPWORK stack by 256 bytes
2019-08-06 23:15:07 -04:00
Daniel Agar
9d701a077d
NuttX reduce stack for interrupts, HPWORK, LPWORK
2019-08-06 11:00:55 -04:00
Daniel Agar
dc10a68539
NuttX and apps update 7.29
2019-07-10 12:58:35 -04:00
Daniel Agar
bef7a9ba8e
NuttX boards increase task limit 32 -> 64 ( #12230 )
2019-06-10 09:42:36 -04:00
Tanja Baumann
fcec3b3efc
px4_fmu-v4: increase uart buffer sizes for vision algorithms ( #12199 )
2019-06-06 09:01:42 -04:00
Daniel Agar
5e6bfe1ad8
vscode updates
...
* working debugging (one click build and debug)
* SITL jmavsim
* SITL gazebo
* jlink px4_fmu-v{2-5}
* improved syntax highlighting
* GNU linker files
* ROS message files msg/*.msg
* jinja2 template files
* fixed intellisense support
2019-03-22 20:55:39 -04:00
Daniel Agar
8f32f3a0c8
px4_fmu-v4 stackcheck compress defconfig
2019-03-21 08:41:01 -04:00
Daniel Agar
41ff6c60ba
px4_fmu-v4 nsh compress defconfig
2019-03-21 08:41:01 -04:00
David Sidrane
edd9f91a19
board:Set larger stack margin
2019-03-01 23:45:48 -05:00
David Sidrane
6f9a9b3d2c
px4_fmu-v4: add runtime external SPI4 detection to support pmw3901 ( #11301 )
...
* The build is built with SPI4. At run time the signal GPIO_8266_GPIO2 it tested. If it is low the SPI4 is configured. If it is high SPI4 is not configured.
* board_common: Add Notion of Board has bus manifest
2019-01-29 13:44:15 -05:00
David Sidrane
938f1453fe
px4_fmu-v4: Inital commit NuttX 7.27+
2019-01-25 06:32:37 -08:00
Daniel Agar
744bacd424
boards/ enforce astyle
2018-12-04 01:06:54 -05:00
Daniel Agar
abb3817d31
boards new split VENDOR_MODEL naming convention
2018-11-26 14:40:14 -08:00
Daniel Agar
f692ad04d0
boards organization
2018-11-26 14:40:14 -08:00