The mavlink_tests module was deleted in 1009268d311 but several
references were left behind, breaking builds on all targets.
Removed:
- CMakeLists.txt: add_subdirectory(mavlink_tests)
- mavlink_ftp.cpp: #include of deleted mavlink_ftp_test.h
- mavlink_ftp.h: MavlinkFtpTest forward decl and friend class
- posix-configs/SITL/init/test/test_mavlink: dead init script
- sitl_tests.cmake: sitl-mavlink CTest target
- install-voxl.sh: px4-mavlink_tests symlink
Ref: https://github.com/PX4/PX4-Autopilot/issues/26738
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* refactor: use parseDefaultArguments
* style: reverted changes to docs (should be auto-generated)
* refactor: use parseDefaultArguments
* style: reverted changes to docs (should be auto-generated)
- split up old module into two, one handling setpoint generation, one control
- add lateral and longitudinal control setpoints topics that can also be
injected from companion computer
- add configuration topics that (optionally) configure the controller
with limits and momentary settings
Signed-off-by: RomanBapst <bapstroman@gmail.com>
- vehicle_angular_velocity: ESC RPM notch filters minimize filter resets
- only allow one filter init per axis per cycle
- "park" ESC notch filters at min frequency instead of full disable
- relax timeout before a notch filter is disabled
- add new parameter IMU_GYRO_DNF_MIN for configuring the minimum notch filter frequency
- new modules/simulation directory to collect all simulators and related modules
- new Tools/simulation directory to collect and organize scattered simulation submodules, scripts, etc
- simulation module renamed to simulator_mavlink
- sih renamed to simulator_sih (not a great name, but I wanted to be clear it was a simulator)
- ignition_simulator renamed to simulator_ignition_bridge
- large sitl_target.cmake split by simulation option and in some cases pushed to appropriate modules
- sitl targets broken down to what's actually available (eg jmavsim only has 1 model and 1 world)
- new Gazebo consistently referred to as Ignition for now (probably the least confusing thing until we fully drop Gazebo classic support someday)
- new static notch filter configured via IMU_GYRO_NF1_FRQ and IMU_GYRO_NF1_BW
- existing notch parameters IMU_GYRO_NF_FREQ and IMU_GYRO_NF_BW become
IMU_GYRO_NF0_FRQ and IMU_GYRO_NF0_BW
- when estimating the peak frequency the magnitude of side buckets will
be factored in, so it doesn't make sense to potentially treat them as
separatey detected peaks
- initial frequency peak tracking SNR increased from 10->15 db
- after initial detection the threshold decreases to SNR 5db
- gyro_fft large method refactored into smaller pieces
- sensors/vehicle_angular_velocity: dynamic notch FFT make sample rate
check a percentage and relax lower bound safety threshold
Using mixers on the IO side had a remote benefit of being able to
override all control surfaces with a radio remote on a fixed wing.
This ended up not being used that much and since the original design
10 years ago (2011) we have been able to convince ourselves that the
overall system stability is at a level where this marginal benefit,
which is not present on multicopters, is not worth the hazzle.
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
Co-authored-by: Daniel Agar <daniel@agar.ca>
- change default FFT length (1024 -> 512)
- this doubles the update rate because half the number of samples are required for each
- decrease number of peaks (4 -> 3)
- so far 3 seems to be sufficient on most vehicles
- increase median filter window (3 -> 5)
- decrease SNR requirement (likely needs to be configurable)
- the ekf2 frontend typically runs in the background for up to 30 seconds waiting for all instances to appear, but this isn't supported by the legacy posix launcher
UART is the primary interface for telemetry radio: https://docs.emlid.com/navio2/ardupilot/hardware-setup/#uart-radio
Check first if /dev/ttyUSB0 exists (https://docs.emlid.com/navio2/ardupilot/hardware-setup/#usb-radio); if not, fall back to configuring over UART (/dev/ttyAMA0).
Use stricter check for character special file (-c) rather than just file (-f).
'console=serial0,115200' needs to be removed from /cmdline.txt as additional configuration step. This should be documented in the Navio2 section of docs.px4.io. Presumably, this is already performed as part of the Raspberry Pi OS prebuilt image Emlid spins.
