- for FW the primary range finder usage is estimating the distance to
the ground (terrain estimate) to guide the landing approach and initiate flare
- increase EKF2_RNG_QLTY_T default 1->3 seconds
* added a new driver ASP5033 for measuring the differential pressure and airspeed
---------
Co-authored-by: nano <nanobotzhe@abv.bg>
Co-authored-by: Denislav Petrov <you@example.com>
This adds support for the TI LP5562 RGB LED driver.
Things to note:
- The driver is initialized in simple PWM mode using its internal clock,
for R,G,B, but not for W(hite).
- The chip doesn't have a WHO_AM_I or DEVICE_ID register to check.
Instead we read the W_CURRENT register that we're generally not using
and therefore doesn't get changed.
- The current is left at the default 17.5 mA but could be changed using
the command line argument.
Datasheet:
https://www.ti.com/lit/ds/symlink/lp5562.pdf
Signed-off-by: Julian Oes <julian@oes.ch>
5s is a more reasobale time for tailsitters, which rely differently on this param
than other VTOL types. Tailsitters will ramp the pitch up withing this time,
while for other VTOLS types its only the max transitiont time.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
A default of 10s makes more sense compared to the old 4s, as this is only the
max time of a back transition and it's also decleared completed if the
speed drops below the hover cruising speed (MPC_XY_CRUISE).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
There have been substantial TECS changes lately, and the config files
for custom VTOLs have not been updated since a long time. I would thus
rather use the default TECS gains for lightly maintained configs.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
The attitude frame is wrong for tailsitters doing side slip fusion for wind estimation.
It doesn't take into account that the frames is 90deg tilted in FW flight.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Set this flag to true if local position is valid but accuracy low, such that
the operator can be warned before system switches to position-failure failsafe.
Additionally, switch to RTL if currently in Mission or Loiter to try to reach home
or fly out of GNSS-denied area.
Set low accuracy threshold to 50m by default for FW and VTOL.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* Fixedwing rate control into a separate module
* Start fw_rate_control for vtol
* Move over airspeed related parameters to fw_rate_control
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
Add ARK_FMU_V6X to RCS netman
Remove arkv6x rc single wire
Fix arkv6x mtd
arkv6x bootloader init all pins to prevent power cycling peripherals on boot
arkv6x don't power cycle sd card on boot
arkv6x add UART4 Telem 4
MIS_LTRMIN_ALt was used to limit the go-to altitude of a LOITER_TO_ALT (not the exit altitude,
but the altitude that the vehicle went to to fly to WP), and during landing abort to climb to
at least this altitude. The min entry altitude of LOITER_TO_ALT I remove with this commit, while
for the min alt during abort I added the new parameter MIS_LND_ABRT_ALT.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Replace the existing check for the availability of a takeoff mission item with a combined
check for takeoff and landing item (or landing pattern). New param MIS_TKO_LAND_REQ
can be set to require only a takeoff, only a landing, both takeoff and landing, and
both or none. The latter is meant to be set if is e.g. deemed unsafe to start a flight
through a Takeoff WP without though defining a Landing - as then in case of a RTL the
vehicle doesn't follow a pre-defined path but instead only can do default RTL that especially
for FW and VTOL isn't always safe.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* Enable motor controls for fixed wing mode in tailsitters
This commit enable motor controls in fixed wing mode for tailsitters
This is needed for enabling quad tailsitters
* VTOL: differential thrust in FW: adapt params to be generic for all axes
Until now only suppoted on yaw axis. Not to be supported also on Roll and Pitch.
- VT_FW_DIFTHR_EN: make bitmask for all three axes independently. First bit is Yaw,
sucht that existing meaning of VT_FW_DIFTHR_EN doesn't change.
- VT_FW_DIFTHR_SC: rename to VT_FW_DIFTHR_S_Y and add same params for roll (_R) and
pitch (_P).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* Integrate differential control bits to three axis control
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- rcS parameter backup try to directly restore param (FRAM) from backup (in case SD card is removed before successful export)
- rcS parameter backup logging rearrange to capture more logging output (param_import_fail.txt)
- posix rcS try to keep param backup and restore roughly in sync with NuttX rcS
- tinybson fix debug printf format
- param_export_internal ensure file descriptor positioned at 0 (precaution)
Daniel Agar