When we fall back to another link, we are already doing a uORB copy when
checking the data. Therefore, we should further down use/send that data
instead of overwriting it immediately.
Signed-off-by: Julian Oes <julian@oes.ch>
I don't think it makes sense to slow down switching RTCM injection to
once every 5 seconds. If we don't have corrections, we should check and
use whatever we get as soon as possible.
Signed-off-by: Julian Oes <julian@oes.ch>
We need to reset the instance after looping through all instances.
Otherwise, we are left with the last instance if none is valid but have
not updated the _selected_rtcm_instance which is what is logged.
Therefore, this change fixes the logged RTCM instance.
Signed-off-by: Julian Oes <julian@oes.ch>
Maximum plaintext length was wrong, it is just k - 2 * hLen -2, where k is RSA key modulus length and hLen is hash length
Also minimum block that can be encrypted didn't make sense for RSA-OAEP, it is just 1 byte, the rest will be padded.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Bootloader needs to have a mechanism to de-initialize crypto, in case some HW accelerator
is being used. This adds the needed function for it
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This adds a parser for Unicore sentences sent in-between NMEA sentences.
This brings support for the Unicore UM982 module which publishes heading
information based on the two antennas.
Signed-off-by: Julian Oes <julian@oes.ch>
It turns out that when you rotate by 45 degrees, as required on the
CubeOrange+, then you can easily get into clipping because the vector
components are constrained after the rotation. In order to avoid that,
we have to avoid getting close to the int16 range and switch from 20 bit
resolution to 16bit resolution earlier.
Signed-off-by: Julian Oes <julian@oes.ch>
- always publish esc_status
- when enabled via MODAL_IO_VLOG param, enable actuator debug output
- for modal_io commands, use ESC HW ID values instead of motor number for easier use
- publish esc_status message for command line commands
- Uncommented the code that fills in the cmdcount and power fields in the esc_status topic
---------
Co-authored-by: Travis Bottalico <travis@modalai.com>
- vectornav library (libvnc) fixed for NuttX
- open serial port O_NONBLOCK (like __APPLE__)
- set serial port baud rate with cfsetspeed (like __APPLE__)
- vectornav backend thread increase stack and run at higher priority (SCHED_FIFO)
* Cyphal: fix comparing floating-point issue
* Cyphal: fix setpoint serialization
* Cyphal: fix bug with wrong comparasion of param name and pub/sub name: remove prefix from UavcanPublisher::updateParam and UavcanDynamicPortSubscriber::updateParam and PublicationManager::updateDynamicPublications
* Cyphal: integrate UavcanEscController with PublicationManager, remove second instance of UavcanEscController from CyphalNode
* Cyphal: publish readiness with minimal frequency because according to UDRAL The drive shall enter STANDBY state automatically if the readiness subject is not updated for CONTROL_TIMEOUT
* Cyphal: increase setpoint publish rate from ~75 to 200 by removing PX4_INFO (it really significantly react on the the output rate) and changing the mixing output rate and the shedule interval
* Cyphal: restore prefix because we need it for uorb over uavcan/cyphal and add udral prefix for non uorb pub/sub
* Cyphal: fix DynamicPortSubscriber subscription: if it has multiple subscribers, it should call subscription only after updating of all port subscribers port identifiers
* Cyphal: fix SubscriptionManager: we should take care about prefix
* Cyphal: fix readiness for test motor mode
* [Cyphal] Fix dynamicsubscription, improve printinfo, enable MR-CANHUBK3 config
---------
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
- new FIFO_RESET state used to give the sensor more time after successful configuration before sampling begins
Co-authored-by: Mathieu Bresciani <brescianimathieu@gmail.com>
Thomas Debrunner