- added support for BQ40Z80 based battery
- added performance counter for interface errors
- added SMART_BATTERY_INFO mavlink message
- general code cleanups and optimization
- fixed: void flooding the log in case of interface error
- fixed: using _batt_startup_capacity instead of _batt_capacity for discharged_mah
- update: read manufacture_date
- update: get _cell_count from parameter and not const 4
- update: avoid re-reading data that has already been read and stored on class already
- currently the battery type defined by BAT_SMBUS_MODEL parameter and not by auto detection
- perform reset as per the datasheet (disable I2C immediately, set power mode, wait for appropriate time, etc)
- remove interrupt perf counter and instead only count misses
- minor style changes to stay in sync with the other Invensense drivers
- perform reset as per the datasheet (disable I2C immediately, set power mode, wait for appropriate time, etc)
- only track consecutive errors (not total) to trigger full reset if necessary
- remove interrupt perf counter and instead only count misses
- minor style changes to stay in sync with the other Invensense drivers
- perform reset as per the datasheet (disable I2C immediately, set power mode, wait for appropriate time, etc)
- only track consecutive errors (not total) to trigger full reset if necessary
- remove interrupt perf counter and instead only count misses
- minor style changes to stay in sync with the other Invensense drivers
- perform reset as per the datasheet (wakeup accel/gyro and wait before proceeding)
- add register bank selection (not yet used)
- track consecutive errors to trigger full reset if necessary
- remove interrupt perf counter and instead only count misses
- minor style changes to stay in sync with the other Invensense drivers
- perform reset as per the datasheet (wakeup accel/gyro and wait before proceeding)
- add register bank selection (not yet used)
- track consecutive errors to trigger full reset if necessary
- remove interrupt perf counter and instead only count misses
- minor style changes to stay in sync with the other Invensense drivers
- perform reset as per the datasheet (disable I2C immediately, set power mode, wait for appropriate time, etc)
- remove interrupt perf counter and instead only count misses
- minor style changes to stay in sync with the other Invensense drivers
- perform reset as per the datasheet (disable I2C immediately, set power mode, wait for appropriate time, etc)
- only track consecutive errors (not total) to trigger full reset if necessary
- remove interrupt perf counter and instead only count misses
- minor style changes to stay in sync with the other Invensense drivers
- update copyright year
- perform reset as per the datasheet (disable I2C immediately, set power mode, wait for appropriate time, etc)
- only track consecutive errors (not total) to trigger full reset if necessary
- remove interrupt perf counter and instead only count misses
- minor style changes to stay in sync with the other Invensense drivers
- perform reset as per the datasheet (disable I2C immediately, set power mode, wait for appropriate time, etc)
- track consecutive errors and trigger full reset if necessary
- remove interrupt perf counter and instead only count misses
- minor style changes to stay in sync with the other Invensense drivers
- read FIFO count along with full transfer as a sanity check
_num_outputs is set according to the mode_pwmX call, which is required
for camera triggering.
This fixes camera triggering via PWM, as it avoids overwriting the channel.
- always check system field for validity
- reject any data outside of "servo position" valid range from Spektrum specification
- properly support XPlus channels (12+)
- debug message if channel count changes
1. The spec specifies that the mode change condition should be met for 10
consecutive frames before changing to the next mode.
2. The spec (and comment) says that "PAW3902JF should not operate with Shutter < 0x01F4 in Mode 2" -
however the if condition checked the reverse condition
Signed-off-by: Koby Aizer <koby.aizer@tg-17.com>
I changed the input constraint in #15349 but screwed up the usage
because I was convinced it's püass by reference. I'll double check
for sure next time.
- the latch would actually cause more problems if the backup schedule hit
- this reduces the number of cycles where the FIFO is actually empty at max rate (when there's only 1 sample in the FIFO expected)
Daniel Agar