I don't think we should change the logging profile based on the type of
airframe configured. Instead, this is an option you set based on the
phase of development/testing you're in.
This came up because the KakuteH7v2 which is 4050 by default would log
excessively which is not a good idea with only 128 MB flash storage.
* s32k3xx: EMIOS allow independent frequencies for each channel
* mr-canhubk3: update config
* mr-canhubk344: Fix adap board detect
* mr-canhubk344: Use LPSPI1 (Port P1A) for SD card
* airframes: Add B3RB Ackermann rover config
See https://nxp.gitbook.io/mr-b3rb for more information about the NXP
B3RB platform. PX4 Support basic control for now
In an effort to reduce configuration space.
I've not seen use for this option.
If a pilot flies manually in position mode he has some visual reference of the vehicle and can do better than an autonomous mode without position reference.
Also by now we have nudging in Descend mode so the pilot can still give input and the only difference is it automatically goes down instead of the pilot having to descend by stick to land.
* rft: clean merge to PX4
* fix: formatting
* fix: extra line
* fix: moved submarine out of "is_ground_vehicle", added proper check for center-throttle
* feat: updated gazebo models to include bluerov update
* fix: use 'is_uuv_vehicle', remove FW_MM/LLC from uuv build
* fix: added saturation to thrust and torque messages via param
* doc: updated parameters documentation for uuv
* fix: formatting
* feat: matching hardware reference
* fix: thrusters kg
* rft: removed commented lines
* fix: update gz reference given hw setup
* fix: hardware references
* fix: recommendations
* fix: updated settings to match hardware
* rft: check only for fixed and rotary wing for high throttle
Co-authored-by: Daniel Agar <daniel@agar.ca>
* fix: commit oupsie
* fix: format
* rft: remove is_uuv
* fix: hw parameters, uuv build target for v6x
* feat: added support for D-pad attitude changes in stabilized position control
* fix: position setpoint update and parametrized trajectory age and att change
* fix: format
* fix: removed duplicated call to check_validity_setpoint
* fix: setpoint update on arming logic
* fix: setpoint initialization for stabilized mode
---------
Co-authored-by: Daniel Agar <daniel@agar.ca>
* rft: initial merging of controllers for spacecraft vehicles
* feat: rate controller nominal
* feat: spacecraft tooling for commander and VehicleStatus
* feat: spacecraft tooling for commander and VehicleStatus
* fix: format
* fix: format
* fix: remove iostream
* fix: remove iostream
* feat: spacecraft attitude control and minor refactoring of params
* feat: add position controller
* fix: format
* fix: moved trajectories to new message, removed derivative filters
* fix: format
* fix: removed extra newline
* fix: spacecraft allocation builds
* feat: add thrusters to effectivenes, add spacecraft build to cmake, clean comments
* feat: required changes for allocation
* feat: thruster simulation interface
* fix: update maximum and minimums
* fix: format
* fix: added newline at the end of spacecraft actuator effectiveness
* feat: configurable board pwm freq from Kconfig
* feat: mavlink compliant spacecraft definition
* feat: add orbiter to define
* boards: Increase TELEM2 rx buffer size for DDS over serial use-case (ARK Jetson)
feat: spacecraft tooling for commander and VehicleStatus
fix: format
fix: remove iostream
feat: mavlink compliant spacecraft definition
* feat: add orbiter to define
* feat: add orbiter to define
* fix: change mav_type to new spacecraft orbiter enum value
* fix: build issue
* feat: update mavlink
* feat: update mavlink to latest master with spacecraft
* feat: update mavlink
* feat: update mavlink to latest
* feat: cleanup and synchronization with new mavlink vehicle definition
* fix: get away without specifying spacecraft vehicle
* fix: removed unnecessary definition
* fix: format
* feat: cmake variant for spacecraft
* feat: proper mav_type and rc init
* fix: removed dart from build system
* add: thrusters to actuator type
* rft: reordering actuator type
* rft: initial merging of controllers for spacecraft vehicles
* feat: rate controller nominal
* fix: format
* feat: spacecraft attitude control and minor refactoring of params
* feat: add position controller
* fix: format
* fix: moved trajectories to new message, removed derivative filters
* fix: format
* fix: removed extra newline
* fix: spacecraft allocation builds
* feat: add thrusters to effectivenes, add spacecraft build to cmake, clean comments
* feat: required changes for allocation
* feat: thruster simulation interface
* fix: update maximum and minimums
* fix: format
* fix: added newline at the end of spacecraft actuator effectiveness
* feat: configurable board pwm freq from Kconfig
* feat: add orbiter to define
* feat: cleanup and synchronization with new mavlink vehicle definition
* fix: get away without specifying spacecraft vehicle
* fix: conflicts
* fix: format
* fix: remove duplicate entry
* rft: remove Kconfig changes
* rft: revert main Kconfig
* rft: revert main kcoonfig on platforms
* rft: remove changes to board PWm (go on another PR)
* rft: revert changes to commander (main is correct)
* fix: extra char on commander_helper
* rft: removed extra spaces
* rft: moved effectiveness to spacecraft
* fix: spacecraft effectiveness
* fix: extra space
* feat: preliminary version, still using thrusters
* rft: initial pipeline on PX4 side with rotors instead of thrusters
* feat: add atmos model
* feat: spacecraft with rotor pipeline tested, working
* feat: update gz
* rft: removed thruster interfaces
* fix: format
* fix: remove control allocation
* fix: thruster normalization
* fix: format
* fix: nuttx version
* fix: clang tidy error
* feat: updated gz to add atmos model
* fix: update gz
* fix: update mavlink
* fix: remove friend class from allocation lib
* fix: remove actuator_outputs/motors
---------
Co-authored-by: Alexander Lerach <alexander@auterion.com>
* fix sign error in appropriate place
In PR https://github.com/PX4/PX4-Autopilot/pull/24175 I changed the
control surface deflection signs in generate_fw_aerodynamics to make the
1103 airframe work correctly. However, this breaks the 1101 airframe,
introducing sing errors there.
So, here the change in generate_fw_aerodynamics is reverted to the state
before PR #24175. Instead, the signs are set correctly by using
the HIL_ACT_REV bitfield in the respective airframe config files.
* match control surface parameters to SIH model
* add standard vtol airframe to SIH.
mostly took changes from 4d930bde and applied to main.
generate_fw_aerodynamics now takes four arguments rather than using the
_u class member, because depending on vehicle type _u is used
differently.
The default implementation for multicopter Position mode is FlightTaskManualAcceleration.
The last missing piece was support for CollisionPrevention in this implementation.
Julian Oes