nxp/rt117x:Fix Pin IRQ
nxp/rt117x:Support 4 i2c busses
nxp/rt117x:Add px4io_serial support
nxp/imxrt:Expand ToneAlarmInterface to GPT 3 & 4
px4_fmu-6xrt:Using imxrt_flexspi_nor_octal
px4_fmu-6xrt:Entry is start
px4_fmu-6xrt:Add Proper MTD
px4_fmu-6xrt:Set I2C Buses
px4_fmu-6xrt:Proper SPI usage
px4_fmu-6xrt:Adjust memory Map to use the 2 MB
px4_fmu-6xrt:Bring in ROMAPI
px4_fmu-6xrt:Push FLASH to 200Mhz
px4_fmu-6xrt:Use BOARD_I2C_LATEINIT
px4_fmu-6xrt:Clock Config remove unused devices
px4_fmu-6xrt:Remove EVK SDRAM IO
px4_fmu-6xrt:Enable SE550 using HW_VER_REV_DRIVE
px4_fmu-6xrt:Use MTD to mount FRAM on Flex SPI
px4_fmu-6xrt:Manifest
px4_fmu-6xrt:Restore board_peripheral_reset
px4_fmu-6xrt:Set I2C buss Interna/Externa and startup
nxp/rt117x:Set 6 I2C busses
px4_fmu-6xrt:Correct Clock Sources and Freqency Settings
px4_fmu-6xrt:Correct ADC Settings
px4_fmu-6xrt:Tune FlexSPI config and sync header with debug variant Linker prep for rodata ahb partitioning
px4_fmu-6xrt:FlexSPI prefetch partition split .text and .rodata
Current config
1KB Prefetch .rodata
3KB Prefetch .text
px4_fmu-6xrt:Run imxrt_flash_setup_prefetch_partition from ram with barriers
px4_fmu-6xrt:Use All OCTL setting from FLASH g_flash_config SANS lookupTable
px4_fmu-6xrt:Octal spi boot/debug problem bypass
px4_fmu-6xrt:Add PWM test
px4_fmu-6xrt:Fix clockconfig and USB vbus sense
px4_fmu-6xrt: Use TCM
px4_fmu-6xrt: Ethernet bringup
imxrt: use unique_id register for board_identity
px4_fmu-6xrt: update ITCM mapping, todo proper trap on pc hitting 0x0
px4_fmu-6xrt:correct rotation icm42688p onboard imu
rt117x: Add SSARC HP RAM driver for memory dumps
px4_fmu-6xrt: Enable hardfault_log
px4_fmu-6xrt: Enable DMA pool
px4_fmu-6xrt: fix uart mapping
px4_fmu-6xrt: enable SocketCAN & DroneCAN
px4_fmu-6xrt:Command line history TAB completion
px4_fmu-6xrt:Fix pinning duplication
px4_fmu-6xrt:Support conditional PHY address based on selected PHY
px4_fmu-6xrt:Add Pull Downs on CTS, use GPIO for RTS
px4_fmu-6xrt:Set TelemN TX Slew rate and Drive Strenth to max
px4_fmu-6xrt::Set TELEM Buffers add HW HS
px4_fmu-6xrt:Turn off DMA poll
px4_fmu-6xrt:RC_SERIAL_PORT needed to be px4io to disable rc_input using TELEM2!
px4_fmu-6xrt: bootloader (#22228)
* imxrt:Add bootloader support
* bootloader:imxrt clear BOOT_RTC_SIGNATURE
* px4_fmu-6xrt:Add bootloader
* px4_fmu-6xrt:bootloader removed ADC
* px4_fmu-6xrt:bootloader base bootloader script off of script.ld
* px4_fmu-6xrt:add _bootdelay_signature & change entry from 0x30000000 to 0x30040000
* px4_fmu-6xrt:hw_config Bootloader has to have 12 bytes
px4_fmu-6xrt:Default to use LAN8742A PHY
px4_fmu-v6xrt:VID Set to Drone Code
board_reset:Enable ability to write RTC GP regs
px4_fmu-6xrt:Fix CMP0079 error
rt117x:micro_hal Add a PX4_MAKE_GPIO_PULLED_INPUT
px4_fmu-v6xrt:Set CTS High before VDD_5V applided to ports to avoid radios fro entering bootloaders
fmu-v6xrt: increase 5v down time
fmu-v6xrt:Ready for Release DEBUGASSERTS off and Console 57600,
Bootloder updated.
imxrt:board_hw_rev_ver Rework for 3.893V Ref
px4_fmu-v6xrt:Move ADC to Port3
imxrt:117x Reuse all but io_timer_hw_description and imxrt_pinirq.c
imxrt:ADC & LPADC bifurcation and restructuring
imxrt:hrt support Up to GPT6
nxp/rt117x:adc Corrected
This consolidates the version/revision detection function.
This should allow for actual changes in a follow up commit.
Signed-off-by: Julian Oes <julian@oes.ch>
- Previously, not having a proper boundary check caused overflows in the
buffer (wrong memory access)
- Moreoever, negative size values getting introduced to snprintf &
strncat were also being truncated to unsigned value, hence causing
overflow, so index check needed to be added before both functions
- Fixed typo in board_common.h
- 4096 of 3 hex digits each for rev and ver is enough.
#defines used in SPI versions do not be long format, use use the macro
- Board provides a prefix and the formatting is sized and built in
- No need for funky board_get_base_eeprom_mtd_manifest interface
Original mft is used where the abstraction is done with the MFT interface
Co-authored-by: David Sidrane <David.Sidrane@Nscdg.com>
This fixes the case where oneshot was enabled with multi-instance pwm_out,
triggering oneshot updates too close to each other and as a result could
lead to spinning motors while disarmed.
Peter van der Perk