The implementation before this change had two timeouts, a hard-coded
timeout of 0.5 seconds as well as a by param configurable timeout with
certain failsafe actions set.
This change aims to fix two problems:
1. The hard-coded offboard timeout can be triggered easily with sped up
lockstep simulation. Since i t is hard-coded it can't be adapted to
the speed factor.
2. The offboard signal can time out but no action will be taken just
yet. This means we end up in an in-between stage where no warning or
failsafe action has happened yet, even though certain flags are set
to a timeout state.
This patch aims to fix this by unifying the two timeouts to the existing
configurable param. The convoluted double timeout logic is replaced by a
simple hysteresis.
For anyone that has previously not changed the default timeout param (0),
the param will now be changed to 0.5 seconds which reflects the
previously hardcoded time. For anyone with a specific timeout
configured, the behaviour should remain the same.
Also, going forward, timeouts lower than 0.5 seconds should be possible.
- checked register mechanism and simple watchdog
- driver checks for errors gradually and can reconfigure itself
- respect IMU_GYRO_RATEMAX at the driver level
- fixed sensor INT16_MIN and INT16_MAX handling (y & z axis are flipped before publishing)
- increased sensor_gyro_fifo max size (enables running the driver much slower, but still transferring all raw data)
- PX4Accelerometer/PX4Gyroscope remove unnecessary memsets
The problem with printing the exception was that starting with
Python 3.6 the ImportError is yet another (sub) exception called
ModuleNotFoundError which can't be printed as a string and then triggers
another exception:
```
Traceback (most recent call last):
File "/home/julianoes/src/Firmware/Tools/serial/generate_config.py", line 11, in <module>
import jinja2
ModuleNotFoundError: No module named 'jinja2'
During handling of the above exception, another exception occurred:
Traceback (most recent call last):
File "/home/julianoes/src/Firmware/Tools/serial/generate_config.py", line 13, in <module>
print("Failed to import jinja2: " + e)
TypeError: must be str, not ModuleNotFoundError
```
As per @bkueng's suggestion the easiest is to cast the exception to str
and that way prevent the second exception.
with measurement noise auto-tuning
The purpose of this estimator is to improve land detection and vertical
velocity feedforward
Recovery strategy:
This is required when the setpoint suddenly changes in air or that the
EKF is diverging. A lowpassed test ratio is used as a trigger for the recovery logic
Also, a lowpassed residual is used to estimate the steady-state value
and remove it when estimating the accel noise to avoid increasing the
accel noise when the redisual is caused by an offset.
* Add param for software flow ctl on 3DR radios
* Dont reset telemetry type on radio timeout
* Treat 3DR radio as generic link type
* Rename 3DR to SiK radio
I've added a queue depth of 4 for sensor_accel and sensor_gyro. This is initially added because it's not always possible for the `vehicle_acceleration` to keep up with every publication of the primary accelerator as it runs in the same thread as ekf2, various controllers, etc.
Later this mechanism will be used in a few areas
- rate limit `vehicle_angular_velocity` and `vehicle_acceleration` without missing any raw data
- move IMU integration to `vehicle_imu` and out of the actual driver threads, eliminating the need for sensor_accel_integrated and sensor_gyro_integrated
- integrate raw gyro synchronized with optical flow measurements
- introduces parameter IMU_DGYRO_CUTOFF to configure the angular acceleration low pass filter
- the angular acceleration is computed by differentiating angular velocity after the notch filter (IMU_GYRO_NF_FREQ & IMU_GYRO_NF_BW) is applied
Co-authored-by: Julien Lecoeur <jlecoeur@users.noreply.github.com>
- gyro filtering (low-pass and notch) only performed on primary gyro in `sensors/vehicle_angular_velocity` instead of every gyro in `PX4Gyroscope`
- sample rate is calculated from actual updates (the fixed value was slightly wrong in many cases, and very wrong in a few)
- In the FIFO case the array is now averaged and published in `sensor_gyro` for filtering downstream. I'll update this in the future to use the full FIFO array (if available), but right now it should be fine.
- this is a new module for temperature compensation that consolidates the functionality previously handled in the sensors module (calculating runtime thermal corrections) and the events module (online thermal calibration)
- by collecting this functionality into a single module we can optionally disable it on systems where it's not used and save some flash (if disabled at build time) or memory (disabled at run time)
- split out integrated data into new standalone messages (sensor_accel_integrated and sensor_gyro_integrated)
- publish sensor_gyro at full rate and remove sensor_gyro_control
- limit sensor status publications to 10 Hz
- remove unused accel/gyro raw ADC fields
- add device IDs to sensor_bias and sensor_correction
- vehicle_angular_velocity/vehicle_acceleration: check device ids before using bias and corrections
- this provides some extra space when the FIFO transfers don't align perfectly
- I've also made an effort to keep the different drivers (icm20602, icm20608g, ism330ldc) in sync so we can factor out the common portions later once we've confident in the pattern.
* Treat UAVS diffrently from manned aviation
* Added fake_traffic testing functionality,
* Added NAV_TRAFF_AVOID Hold and Landmode
* Added Behavior: HOLD Position to collision avoidance mode and implemented Landmode to collision avoidance.
Boards where no Hardware GUID is defined will send 0 as GUID.
Right now collision avoidance for more than one FMU without Hardware GUID is not possible.
We should consider adding a randomly generated HW GUID as a placeholder for legacy Boards
We now check individually for empy and genmsg.
Also, my recommendation is to use pip3 as a user to install the
dependencies as this is least intrusive and should work on all
platforms.
* parameter and logic to commander for triggering failsafe from external automatic trigger system.
* logic to startup script for enabling ATS. Added uORB publishing to pwm_input module.
* Refactored out CDev usage from pwm_input and ll40ls. Refactored out ll40ls specifics from pwm_input and cleaned up dead code.
- rename of flag in position sp: from allow_weather_vane to disable_weather_vane
- flag now doesn't have to be set for all auto modes, meaning that weather vane is also active outside of mission
- flag is set before front transition to align with wp, and unset after alignment is over
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
