nxp_ucans32k146:Relocation for Bootloader
nxp_ucans32k146:can_boot enable CAN
nxp_ucans32k146:Save Space use Non Optimize memcpy
nxp_ucans32k146:Increase to 24K
nxp/ucans32k146:Canbootloader LED Driver
nxp_ucans32k146:Can bootloader shut down CAN
nxp_ucans32k146:Use NVMEEPROM for Paramaters
nxp_ucans32k146:Use bootloader AppDescriptor
px4 mtd:Support onchip emulated eeprom
nxp/s32k14x:board_identity: Return length of mfguid
nxp/s32k14x:CAN driver
nxp/s32k14x:Drver Added ABORT on error
canbootloader:Use N words for first word
canbootloader:Ensure the up_progmem API always defined
* stm32_common: Add support for STM32F42x/STM32F43x rev. 5/B
According to ST, both 5 and B share the same REV_ID.
Signed-off-by: Alexey Rogachevskiy <sfalexrog@gmail.com>
* stm32_common: Change comment to match code, change enum names to match revisions
On boot, if board_hardfault_init finds a hardfault stored in BBSRAM, it
checks if there is any data available on stdin to see if there is
somebody there to respond to a prompt. But on boards such as cubeorange
where there is not a serial console by default, the ioctl fails and
bytesWaiting is uninitialized. So it will non-deterministally hang the
boot process with no outside feedback if that value is not zero.
Signed-off-by: Alex Mikhalev <alexmikhalevalex@gmail.com>
S32K1XX HRT: Allow any channel of any FTM timer to be used
NXP UCANS32K: Enable additional FlexTimers and use FTM5 for HRT
NXP UCANS32K - Change FTM clocksource to system oscillator
NXP UCANS32K - Only need one FlexTimer and channel for PWM output
NXP UCANS32K will have only one PWM header by default
S32K1XX support FlexTimers beyond FTM3
S32K1XX io_timer.c - replace references to Kinetis
S32K1XX io_timer.c correct register names
S32K1XX input_capture.c and pwm_servo.c replace references to Kinetis
- drivers/tone_alarm: move to ModuleBase and purge CDev (/dev/tone_alarm0)
- drivers/tone_alarm: only run on tune_control publication (or scheduled note) rather than continuously
- drivers/tone_alarm: use HRT to schedule tone stop (prevents potential disruption)
- msg/tune_control: add tune_id numbering
- systemcmds/tune_control: add "error" special case tune_id
- move all tune_control publication to new uORB::PublicationQueued<>
- start tone_alarm immediately after board defaults are loaded to fix potential startup issues
- for SITL (or other boards with no TONE output) print common messages (startup, error, etc)
- Nuttx only process all suspend & resume scheduling notes when top is running, otherwise only track IDLE
- convert cpuload and print load to c++
- delete unused fields from print_load struct
- update hrt_store_absolute_time (previous unused)
* X7Pro adds CAN driver
* UAVCAN timer selection moved to default.cmake
* Modify some details about @CUAVcaijie UAVCAN timer selection moved to default.cmake
* Put some timer parameters to micro_hal.h from board_config.h. Fix all h7 boards
Co-authored-by: honglang <honglang@cuav.net>
It appear that QGC is now resyncing between operation.
This was causing the bl_state to be reset to STATE_PROTO_GET_SYNC
and loosing the state of (STATE_PROTO_GET_SYNC|STATE_PROTO_GET_DEVICE)
David Sidrane