vtol_type: timeout transition earlier if we use airspeed and airspeed has
not increased above blend airspeed after openloop front transition time.
Signed-off-by: RomanBapst <bapstroman@gmail.com>
---------
Signed-off-by: RomanBapst <bapstroman@gmail.com>
Instead of tracking a fixed deceleration setpoint during the backtransition we added here position feedback,
such that the vehicle comes to a stop latest at the current position setpoint. This reduces the risk of
overshooting the landing point.
If no position feedback/position setpoint is present the old logic still applies.
It further moves the braking controller to the FlightTaskTransition instad of doing it in
the VTOL attitude mode.
* vtol_type: added position feedback to backward transition
* FlgithTaskTransition: refactored backtransition deceleration/pitch setpoint computation
* FlightTaskTransition: minor improvements
* FlightTaskTransition: use .dot() consistently and remove unnecessary comments
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
* Remove euler angles from attitude setpoint message
* Remove usage of euler angles in attitude setpoint messages
This commit removes the usage of euler angles in the vehicle_attitude_setpoint messages
* Fix standard vtol
* created a Performance Model for fixed wing vehicle
- added compensation for maximum climbrate, minimum sinkrate, minimum airspeed and trim airspeed based on weight ratio and air density
- added atmosphere lib to standard atmosphere calculations
---------
Signed-off-by: RomanBapst <bapstroman@gmail.com>
Co-authored-by: Thomas Stastny <thomas.stastny@auterion.com>
EffectivenessTiltrotor: link time when to tilt motors to MC position to COM_SPOOLUP_TIME
- remove VT_TILT_SPINUP and special spin up tilt handling form the VTOL module
- now handle the spoolup in the allocation, directly linked to COM_SPOOLUP_TIME
- leave tilts at disarmed value during spoolup
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Experience from tuning different VTOL backtransitions showed only having a
I controller is beneficial over a combined FF/I breaking controller.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Instead of hard-coding the tilting duration (from FW to MC tilt),
expose it as a parameter (VT_BT_TILT_DUR). The default is the same
as the hard-coded value previously (1s).
Slower tilting mechanisms need a higher value here, while for smaller
ones a too high value results in unnecessary delays till the motors
are in hover configuration.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This affects how soon after a backtransition the vehicle has the
full hover controller running again. Specifically it reduces the
duration of the ramp down of the motors prior to tilting them.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* refactored uncommanded descend quadchute
- use fixed altitude error threshold
- compute error relative to higest altitude the vehicle has achieved
since it has flown below the altitude reference (setpoint)
* disabled altitude loss quadchute by default
* altitude loss quadchute: added protection against invalid local z
---------
Signed-off-by: RomanBapst <bapstroman@gmail.com>
Transitions in Stabilized mode are done manually, the pilot controls the pitch angle
and if it's above the threshold the transition is declared finished (plus airspeed
check for front transition). Thus we can't have fixed thresholds but need to link
them to the actual max pitch angle in Stabilized mode.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Silvan