* Add tflm to px4 with module
- Add TensorFlow Lite Micro(TFLM) as a library in px4
- Make a module that uses neural network inference for control, which uses TFLM for inference
- Make board config files for PX4 with neural module
* Added neural flight mode
* Add posibility to read of inference times
* Fix comments from review:
- Switch ssh link to https link in submodule
- Remove mc_nn_control from startup
* Add tflm to px4 with module
- Add TensorFlow Lite Micro(TFLM) as a library in px4
- Make a module that uses neural network inference for control, which uses TFLM for inference
- Make board config files for PX4 with neural module
* Added neural flight mode
* Add posibility to read of inference times
* Remove auto start
* Add logging from neural control module
* Fix automatic startup to only be when module is included
* Switch to flight mode registration
* Add docs
* Change min/max/coeff to actual parameters
* add figures to neural network docs
* Switch to e2e network
* Remove toolchain changes and replace with instructions in docs
* Get ready for merge after toolchain upgrade
* switch back to submodule
* Try to figure out cmake
* Get CI working with new toolchain
* Remove fork dependency
* Finalize PR
* fix toolchain inclusion
* Fix ctype_base.h include
* Cleanup includes for TFLM
* Remove redundant std
* Update FW module names in board files
* Fix docs
* Remove cstdlib copy
* Copy header from nuttx
* Prettier, markup, layout
* NeuralControl.msg - update uorb comments to current standard
* Add description to neural topic
* Fix typo
* Typo
* TFLM and Module utitlities
* Neural networks top level
* Update docs
* Add manual control
* Update docs
* Revert the manual control attempt
* Update docs/en/advanced/nn_module_utilities.md
* Add posibility to set trajectory setpoint with manual control
---------
Co-authored-by: Pedro Roque <padr@kth.se>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
Note: Some files are autogenerated and I did not yet
go through each source of generation to fix it there.
Instead I adjusted the filter to only exclude those
such that we can fix things in steps.
* ZMO airframe: update parameters
Including some parameters we found useful during the tests over the
previous months:
- various controller & transition tuning refinements
- remove battery capacity (not reliable enough w battery degradation)
- airspeed scale
- rotor configs:
- remove everything related to rotors 3 and 4 (which don't exist)
- set moment coefficients explicitly even if at default
- Increase roll limit (FW_R_LIM, FD_FAIL_R)
- min and max airspeeds
- tilt servo min and default PWM values
* ZMO airframe: address review
- explicitly set CA_ROTOR3_* to 0 (as these are set in the parent
13100 which describes a quadrotor)
- remove ASPD_SCALE_1 (close enough to default, and better to have
slightly low reading)
- remove MPC_ACC_HOR_MAX (= default)
- remove MPC_TILTMAX_AIR (was temporary)
- remove SENS_EN_SF1XX (= default)
* ZMO airframe: update tilt setup
to describe a setup where tilt servos can provide yaw torque in both
directions in multicopter mode.
* ZMO airframe: wording
* hrt: Fix PPM input on channel 2
The CCMR1_PPM define for PPM input on channel 2 was incorrectly set to 2,
which was setting bits for channel 1 instead of channel 2. This prevented
PPM input from functioning properly on channel 2.
Changed CCMR1_PPM for channel 2 from 2 to (1 << 8), which correctly
configures the CC2S bits for input capture mode on TI2.
This fixes an issue noted in the existing code comment:
"FIXME! There is an interaction in the CCMR registers that prevents
using Chan 1 as the timer and chan 2 as the PPM"
Tested on STM32H743 with PPM input on PC7 (TIM8_CH2).
* rc_input: enable sharing serial and PPM pin
By setting RC_SERIAL_PORT_SHARED_PPM_PIN_GPIO_RX it is now possible to
use the same pin on the STM32 for PPM input as well as serial input.
* boards: Add support for Holybro KakuteH7-Wing
* Docs: add moving platform
documenting the addition in #24471
* Moving platform docs: address review
- Release note, write release in docs
- Describe configuration also in main gazebo sim docs, syntax section
- Tip that plugin can be used in other worlds, linking to plugin readme
* Update docs/en/sim_gazebo_gz/index.md
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
---------
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Add vitepress tree
* Update existing workflows so they dont trigger on changes in the docs path
* Add nojekyll, package.json, LICENCE etc
* Add crowdin docs upload/download scripts
* Add docs flaw checker workflows
* Used docs prefix for docs workflows
* Crowdin obvious fixes
* ci: docs move to self hosted runner
runs on a beefy server for faster builds
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* ci: don't run build action for docs or ci changes
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* ci: update runners
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* Add docs/en
* Add docs assets and scripts
* Fix up editlinks to point to PX4 sources
* Download just the translations that are supported
* Add translation sources for zh, uk, ko
* Update latest tranlsation and uorb graphs
* update vitepress to latest
---------
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
