- split out integrated data into new standalone messages (sensor_accel_integrated and sensor_gyro_integrated)
- publish sensor_gyro at full rate and remove sensor_gyro_control
- limit sensor status publications to 10 Hz
- remove unused accel/gyro raw ADC fields
- add device IDs to sensor_bias and sensor_correction
- vehicle_angular_velocity/vehicle_acceleration: check device ids before using bias and corrections
- this provides some extra space when the FIFO transfers don't align perfectly
- I've also made an effort to keep the different drivers (icm20602, icm20608g, ism330ldc) in sync so we can factor out the common portions later once we've confident in the pattern.
* Treat UAVS diffrently from manned aviation
* Added fake_traffic testing functionality,
* Added NAV_TRAFF_AVOID Hold and Landmode
* Added Behavior: HOLD Position to collision avoidance mode and implemented Landmode to collision avoidance.
Boards where no Hardware GUID is defined will send 0 as GUID.
Right now collision avoidance for more than one FMU without Hardware GUID is not possible.
We should consider adding a randomly generated HW GUID as a placeholder for legacy Boards
The bulk of this change was tightly coupled and needed to be deleted in one pass. Some of the smaller changes were things that broke as a result of the initial purge and subsequently fixed by further eradicating unnecessary platform differences. Finally, I deleted any dead code I came across in the related files I touched while going through everything.
- DriverFramework (src/lib/DriverFramework submodule) completely removed
- added dspal submodule in qurt platform (was brought in via DriverFramework)
- all df wrapper drivers removed
- all boards using df wrapper drivers updated to use in tree equivalents
- unused empty arch/board.h on posix and qurt removed
- unused IOCTLs removed (pub block, priv, etc)
- Integrator delete methods only used from df wrapper drivers
- commander: sensor calibration use "NuttX version" everywhere for now
- sensors: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- battery_status: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- cdev cleanup conflicting typedefs and names with actual OS (pollevent_t, etc)
- load_mon and top remove from linux boards (unused)
- delete unused PX4_MAIN_FUNCTION
- delete unused getreg32 macro
- delete unused SIOCDEVPRIVATE define
- named each platform tasks consistently
- posix list_devices and list_topics removed (list_files now shows all virtual files)
- fixed df_ltc2946_wrapper battery dependency
- fixed px4::atomic fetch_add for QuRT
- updated PX4 QuRT SPI wrapper to set bus frequency
- renamed "qurt-default" configs to just "qurt"
- this is one of the last pieces of the system that still depend on DriverFramework
- add new SIM_GPS_NOISE_X parameter for optionally increasing the GPS noise multiplier (was previously a gpssim command line option)
- add SIM_x_BLOCK parameters to block sensor publication
- SIM_GPS_BLOCK
- SIM_ACCEL_BLOCK
- SIM_GYRO_BLOCK
- SIM_MAG_BLOCK
- SIM_BARO_BLOCK
- SIM_DPRES_BLOCK
* parameter and logic to commander for triggering failsafe from external automatic trigger system.
* logic to startup script for enabling ATS. Added uORB publishing to pwm_input module.
* Refactored out CDev usage from pwm_input and ll40ls. Refactored out ll40ls specifics from pwm_input and cleaned up dead code.
The sensor comes in three variants with different gyro measurement ranges. This patch allows auto-detection of the model at startup and sets the scale factor associated with the particular model.
- instrumenting PX4 Matrix and Param methods is too burdensome
- partially restore px4_fmu-v5_stackcheck and holybro_durandal-v1_stackcheck to match default configs
* NotchFilter: add NotchFilter template and test for float type
* NotchFilterTest: add test for Vector3f notch filter
* PX4Gyroscope: add notch filter with IMU_GYRO_NF_(FREQ|BW) parameters to
set the notch center frequency and bandwidth
Daniel Agar