* usb: Added parameter to enable always starting mavlink on USB.
Refactored cdcacm_init into a module and added a paramter to allow always starting mavlink on
USB, also added a paramter to choose the mode. The current default behavior is to wait and listen
for data on USB and auto-detect the protocol (mavlink, nsh, ublox). This results in the mavlink
stream not starting until something else on the mavlink network sends a packet first. The new
default behavior is to always start mavlink.
Added parameters
MAV_USB_ENABLE -- default 1 (always start mavlink on USB)
MAV_USE_MODE -- default 3 (onboard)
* added 3 retries for opening serial port in mavlink, removed sleep before sercon
* added DRIVERS_CDCACM_AUTOSTART to ark-v6x default.px4board
* added CONFIG_DRIVERS_CDCACM_AUTOSTART=y to default.px4board for boards with CONFIG_CDCACM in their nsh/defconfig
* format
* remove PGA460 from COMMON_DISTANCE_SENSOR to save flash
* remove LIS2MDL from COMMON_MAGNETOMETER to save flash
* disable CONFIG_DRIVERS_CDCACM_AUTOSTART for fmu-v5 protected.px4board
* moved and renamed parameters, removed mode logic in mavlink
* changed parameter names, added mode none
* remove parameters from mavlink
IMUs were replaced in V3 with 2x ICM42688P. This configuration should
work with all revisions of Matek F743 Slim board, including V1, V1.5
and interim variant of V3 (ICM42688P + ICM42605).
Signed-off-by: Andrei Korigodskii <akorigod@gmail.com>
- during casual testing on default configs the stack was penetration was reaching ~90% which is a bit too close for comfort
- increasing by 50% to be conservative
* Fixedwing rate control into a separate module
* Start fw_rate_control for vtol
* Move over airspeed related parameters to fw_rate_control
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
- update all msgs to be directly compatible with ROS2
- microdds_client improvements
- timesync
- reduced code size
- add to most default builds if we can afford it
- lots of other little changes
- purge fastrtps (I tried to save this multiple times, but kept hitting roadblocks)
* Adds Timer15 to stm32_common, if the timer base is defined
* Adds Timer15 logic for DMA and AltFunc config on stm32h7 boards
* Adds TIM15 BDTR->MOE support in stm32_common timer init
* Adds support for TIM15 pwm channels on Matek H743 Slim
* Make board_id compatible with ardupilot
* Initialize outputs for CAM1/CAM2 and Vsw pad
* Correct board type 1013 in bootloader to match AP
* Change usb vendor string to "Matek"
* Change cdcacm pid to 1013
* Comment out FLASH_BASED_PARAMS because of #15331
This enables flow control on CDCACM for the NuttX boards which fixes a
problem where HITL would stall.
The stall could happen if the hardware would be a bit too slow in
keeping up with the incoming messages. Often, this happened on arming
because the logger would take some time to log all parameters right at
the beginning.
The stall would then not recover due to NuttX bug where the rx interrupt
would not be restored correctly and instead only a slower watchdog would
release the next read. This watchdog takes 200ms which means it's hard
to impossible to get out of the situation without restarting sim and/or
PX4. For more information about the issue, see:
apache/incubator-nuttx#3633
As a workaround, until that bug is fixed, and because it makes sense
anyway, I propose to enable FLOWCONTROL for the serial via USB.
- cmake NuttX build wrapper compile in place instead of copying source tree to build directory
- slightly faster skipping necessary copying (depending on system)
- allows debugging in place
- easier to work directly in NuttX following official documentation
- simplifies overall build which should make it easier to resolve any remaining NuttX dependency issues in the build system
- the downside is switching back and forth between different builds always require rebuilding NuttX, but I think this is worth the improved developer experience
- also no longer builds px4io and bootloader in every single build, for most users these rarely change and we're wasting a lot of build time
Matthias Grob