The bulk of this change was tightly coupled and needed to be deleted in one pass. Some of the smaller changes were things that broke as a result of the initial purge and subsequently fixed by further eradicating unnecessary platform differences. Finally, I deleted any dead code I came across in the related files I touched while going through everything.
- DriverFramework (src/lib/DriverFramework submodule) completely removed
- added dspal submodule in qurt platform (was brought in via DriverFramework)
- all df wrapper drivers removed
- all boards using df wrapper drivers updated to use in tree equivalents
- unused empty arch/board.h on posix and qurt removed
- unused IOCTLs removed (pub block, priv, etc)
- Integrator delete methods only used from df wrapper drivers
- commander: sensor calibration use "NuttX version" everywhere for now
- sensors: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- battery_status: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- cdev cleanup conflicting typedefs and names with actual OS (pollevent_t, etc)
- load_mon and top remove from linux boards (unused)
- delete unused PX4_MAIN_FUNCTION
- delete unused getreg32 macro
- delete unused SIOCDEVPRIVATE define
- named each platform tasks consistently
- posix list_devices and list_topics removed (list_files now shows all virtual files)
Main UAVCAN protocol handling and ESC updates run on the same thread/wq as
before. There are 2 WorkItems for separate scheduling of the 2, so that
ESC updates run in sync with actuator_control updates. UAVCAN is scheduled
at a fixed rate of 3ms (previously the poll timeout) and on each UAVCAN
bus event.
This leads to roughly the same behavior as before. CPU & RAM usage are
pretty much the same (tested on Pixhawk 4).
Testing done: Motors still work (with feedback), param changes and a
UAVCAN optical flow sensor.
esc_setpoint in UAVCAN was just wrong, this is what it really is:
uint7 power_rating_pct # Instant demand factor in percent
(percent of maximum power); range 0% to 127%.
and remove the px4_ prefix, except for px4_config.h.
command to update includes:
for k in app.h atomic.h cli.h console_buffer.h defines.h getopt.h i2c.h init.h log.h micro_hal.h module.h module_params.h param.h param_macros.h posix.h sem.h sem.hpp shmem.h shutdown.h tasks.h time.h workqueue.h; do for i in $(grep -rl 'include <px4_'$k src platforms boards); do sed -i 's/#include <px4_'$k'/#include <px4_platform_common\/'$k/ $i; done; done
for in $(grep -rl 'include <px4_config.h' src platforms boards); do sed -i 's/#include <px4_config.h/#include <px4_platform_common\/px4_config.h'/ $i; done
Transitional headers for submodules are added (px4_{defines,log,time}.h)
- move most orb to uORB::Publication and uORB::Subscription
- update legacy message handling (warn to PX4_INFO, PX4_WARN, PX4_ERR)
- add perf counters
- sensors/mag support newer `uavcan::equipment::ahrs::MagneticFieldStrength2` message
- sensors/gps support `uavcan::equipment::gnss::Auxiliary` for hdop and vdop
- sensors delete obsolete ioctl and read methods
- use PublicationMulti for actuator_outputs and esc_reports (to coexist with other output modules)
- add GNSS parameter metadata (parameters_injected.xml)
- there is a timeshift between the esc and px4 time so until there is some
kind of offset estimation we are better off using px4 time since the logging
system uses that as reference
Signed-off-by: Roman <bapstroman@gmail.com>
David Sidrane