* PositionSetpoint: remove yaw_valid field
* Navigator: set yaw setpoint to NAN for Takeoff
Don't set a yaw setpoint for takeoff, as Navigator doesn't handle the yaw reset.
The yaw setpoint generation is handled by FlightTaskAuto.
* PositionSetpoint.msg: remove disable_weather_vane and instead only use the yaw field
Strictly follow the concept that if the position_setpoint.yaw is set, then
follow it the controller, and otherwise let the controller set it as it
thinks it's best.
* Navigator: remove logic that sets yaw to be accepted in TAKEOFF
No longer needed as during Takeoff we anyway don't set a yaw setpoint.
* PositionSetpoint.msg: remove yawspeed_valid
* PositionSetpoint.msg: remove yawspeed
* Navigator: set yaw setpoint to NAN instead of current
In set_takeoff and set_land_item, as well as for VTOL transition.
The flight tasks then set the yaw corresponding to the current yaw.
* Navigator: change get_yaw_acceptance into a bool
* PositionSetpoint.msg: improve comment for yaw
* MissionBlock: remove unnecessary code from set_vtol_transition_item
* Navigator: clean up calculate_breaking_stop(), set yaw to NAN
* Navigator: set yaw to NAN in variouls places where not specifc setpoint is desired
* Navigator: set yaw to NAN in reset_position_setpoint()
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Co-authored-by: Matthias Grob <maetugr@gmail.com>
As discussed in the maintainer call we should adhere to the
parameter naming scheme that makes it clear what vehicle type the
configuration is good for.
by only applying the sqrt linear drag when brakeing.
It was originally not done this way to avoid discontinuities and
the exact speed bewlo 1m/s didn't matter. With the position slow mode
the exact slow speeds now matter. And the discontinuities are avoided by
reusing the brake boost filter.
The defintion of the custom symbol M_PI_PRECISE
was not included in one of the only places it's used.
Looks like a mistake that happened in
34c852255e
possibly because a lot of things are included
almost everywhere and if the include order
ligns up there are no compile errors.
Otherwise if is set to Offtrack, which in turn leads to weird behavior.
E.g. when triggering Land while flying fast forward, the vehcile doesn't
descned to the land point it keeps getting a velocity setpoint from the
smoother that pushes it away from the land point.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
When the yaw estimate is converging, the controller makes the drone yaw
in order to follow the current setpoint. This is unintuitive for the
pilot and it is preferable if the drone continues to fly towards the
same physical direction.
A VTOL plane in MC mode has no yaw setpoint during takeoff because of
weather-vane. To align for the front transition, the yaw target jumps
and caused a step in the controller, making it reach saturation.
With this commit, the previous yaw setpoint is set to the current yaw
when no yaw setpoint is sent in order to create a smooth yaw trajectory
starting at the current orientation when yaw target is suddenly finite.
The yawspeed filter also now contains the yaw speed instead of dyaw in
order to prevent chattering due to dt jitter.
with the goal to make it more clear and the error only appear when
armed but every time the running task doesn't actually match
the mapping inside the start_flight_task() function.
- remove deprecated actuator_controls[INDEX_LANDING_GEAR]
- remove dead code in mc rate controller that used to prevent it from being retracted
on the ground (anyway had no effect as it only affected the actuator_control[LANDING_GEAR]
which wasn't sent to the control allocation)
- for VTOLs handle deployment/retraction of landing gear in AUTO as a MC (retract if
more than 2m above ground, deploy if WP is a landing WP), plus additionally when transition
flight task is called (ALTITUDE mode and higher)
- for FW in AUTO: add logic in FW Position Controller, depending on waypoint type mainly
- manual landing gear settings always come through (a manual command overrides a previous
auto command, and vice-versa)
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- Switching to the first order filter that was previously
only in FlightTaskManualAltitude.
- Moving the scaling of full stick deflection to
radians per second into the class.
Matthias Grob