* created a Performance Model for fixed wing vehicle
- added compensation for maximum climbrate, minimum sinkrate, minimum airspeed and trim airspeed based on weight ratio and air density
- added atmosphere lib to standard atmosphere calculations
---------
Signed-off-by: RomanBapst <bapstroman@gmail.com>
Co-authored-by: Thomas Stastny <thomas.stastny@auterion.com>
EffectivenessTiltrotor: link time when to tilt motors to MC position to COM_SPOOLUP_TIME
- remove VT_TILT_SPINUP and special spin up tilt handling form the VTOL module
- now handle the spoolup in the allocation, directly linked to COM_SPOOLUP_TIME
- leave tilts at disarmed value during spoolup
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Experience from tuning different VTOL backtransitions showed only having a
I controller is beneficial over a combined FF/I breaking controller.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Instead of hard-coding the tilting duration (from FW to MC tilt),
expose it as a parameter (VT_BT_TILT_DUR). The default is the same
as the hard-coded value previously (1s).
Slower tilting mechanisms need a higher value here, while for smaller
ones a too high value results in unnecessary delays till the motors
are in hover configuration.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This affects how soon after a backtransition the vehicle has the
full hover controller running again. Specifically it reduces the
duration of the ramp down of the motors prior to tilting them.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* refactored uncommanded descend quadchute
- use fixed altitude error threshold
- compute error relative to higest altitude the vehicle has achieved
since it has flown below the altitude reference (setpoint)
* disabled altitude loss quadchute by default
* altitude loss quadchute: added protection against invalid local z
---------
Signed-off-by: RomanBapst <bapstroman@gmail.com>
Transitions in Stabilized mode are done manually, the pilot controls the pitch angle
and if it's above the threshold the transition is declared finished (plus airspeed
check for front transition). Thus we can't have fixed thresholds but need to link
them to the actual max pitch angle in Stabilized mode.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Once passed the transition and in FW mode, it takes some ms unitl the FW att sp is updated
by the FW att controller. During this time the last published attitude sp is kept bein used,
which is the one that was published during transition. So let's fill the thrust[0] of it.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
A default of 10s makes more sense compared to the old 4s, as this is only the
max time of a back transition and it's also decleared completed if the
speed drops below the hover cruising speed (MPC_XY_CRUISE).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Testing has shown that 10m is a bit too tight, most of all as this check is also run in not height-controlled
flight modes (eg Stabilized), and there 10m altitude loss during transitions can happen easily.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- remove deprecated actuator_controls[INDEX_FLAPS/SPOILERS/AIRBRAKES]
- use new topic normalized_unsigned_setpoint.msg (with instances flaps_setpoint
and spoilers_setpoint) to pass into control allocation
- remove flaps/spoiler related fields from attitude_setpoint topic
- CA: add possibility to map flaps/spoilers to any control surface
- move flaps/spoiler pitch trimming to CA (previously called DTRIM_FLAPS/SPOILER)
- move manual flaps/spoiler handling from rate to attitude controller
FW Position controller: change how negative switch readings are intepreted
for flaps/spoilers (considered negative as 0).
VTOL: Rework spoiler publishing in hover
- pushlish spoiler_setpoint.msg in the VTOL module if in hover
- also set spoilers to land configuration if in Descend mode
Allocation: add slew rate limit of 0.5 to flaps/spoilers configuration change
Instead of doing the flaps/spoilers slew rate limiting in the FW Position Controller
(which then only is applied in Auto flight), do it consistently over all flight
modes, so also for manual modes.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- remove deprecated actuator_controls[INDEX_LANDING_GEAR]
- remove dead code in mc rate controller that used to prevent it from being retracted
on the ground (anyway had no effect as it only affected the actuator_control[LANDING_GEAR]
which wasn't sent to the control allocation)
- for VTOLs handle deployment/retraction of landing gear in AUTO as a MC (retract if
more than 2m above ground, deploy if WP is a landing WP), plus additionally when transition
flight task is called (ALTITUDE mode and higher)
- for FW in AUTO: add logic in FW Position Controller, depending on waypoint type mainly
- manual landing gear settings always come through (a manual command overrides a previous
auto command, and vice-versa)
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Tiltrotor_extra_controls also contains collective thrust beside collective tilt, as passing a 3D
thrust setpoint vector beside the tilt is not feasible.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Previously the condition was based on hard coded height rate estimate and
setpoint values and an altitude error threshold. That showed to be leading
to false positives when the vehicle doesn't tightly follow the altitdue
ramp given by TECS to achieve a new altitude setpoint, and has become
completely infeasibly with the latest TECS rework that leads to non-ramped
altitude setpoint changes in the tecs_status message.
The new check no longer checks the altitude error but only the height rate
instead. It begins to integrate the height rate error once it detects an
uncommanded descend condition (height rate negative while setpoint is
positive). Integral threshold can be tuned by user (VT_QC_HR_ERROR_I).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Strictly follow the following convention for tailsitter:
FW Attitude and FW rate controller always operate in the FW frame, meaning that roll is
roll in FW, which for tailsitter means around the yaw axis in the body frame. The interfaces
between modules is though always in body frame.
That enables us to do the axis transformations for tailsitter, that are currently distributed
all over the controller (attitude, rate, vtol module), only at the input and output data of modules.
Side effect is that the FW rate control tuning gains meanings change: while before the roll gains
where meant for the body axis, they are now always applied for the FW roll axis (also in hover). So
the naming now is correct for FW, while before it was for Hover.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This failsafe flag is currently used for not allowing to re-transition to FW, as well
as disabling pusher assist in hover. Till now it was only possible to reset it with
a commanded transition to MC, which many ground station interfaces didn't allow
as the system, after a quad-chute, already was in MC mode.
Hereby it is changed to reset when a new transition to FW is triggered (either via
RC switch or MAVLink command). It is the users responsibility to assess the situation
after a quad-chute happened to try to transition to FW again, manually proceed/land
the vehicle in MC, or let it finish the defined behavior after a quad-chute.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Roman Bapst