When the yaw estimate is converging, the controller makes the drone yaw
in order to follow the current setpoint. This is unintuitive for the
pilot and it is preferable if the drone continues to fly towards the
same physical direction.
If the measured voltage is more than 65v we need to split the voltage
over multiple cells in order to avoid overflowing the uint16. This is
according to the MAVLink spec.
Signed-off-by: Julian Oes <julian@oes.ch>
The extension fields need to be 0 by default according to the MAVLink
spec. This is because extensions are 0 by default and need to be 0 when
unknown/unused for backwards compatibility.
The patch also simplifies the flow slightly in that it doesn't create a
temporary array but just fills in the cell voltages directly.
Signed-off-by: Julian Oes <julian@oes.ch>
- Enable arbitrary euler angle for Mag rotation
- new CUSTOM rotation enum out of the normal enum range
- mag_rot: automatically change to custom if euler rot is set
- sensor_calibration: Magnetometer save custom rotation parameters
- mag_cal: cross mention rotation parameters
- This allows the user to see the RPY options when searching for the rotation parameter
---------
Co-authored-by: Junwoo Hwang <junwoo@auterion.com>
Co-authored-by: bresch <[brescianimathieu@gmail.com](mailto:brescianimathieu@gmail.com)>
Co-authored-by: Daniel Agar <daniel@agar.ca>
In the mavlink_receiver code, after a while it will try to resend some
parameter update through the MAVLink instance. But for Iridium links
those are not a good idea. So this adds a condition that prevent the
sending if the MAVLink instance is in Iridium mode.
Related to issue #21496
- simplify vehicle_status.arming_state down to just armed and disarmed
- ARMING_STATE_INIT doesn't matter
- ARMING_STATE_STANDBY is effectively pre_flight_checks_pass
- ARMING_STATE_STANDBY_ERROR not needed
- ARMING_STATE_SHUTDOWN effectively not used (all the poweroff/shutdown calls loop forever in place)
- ARMING_STATE_IN_AIR_RESTORE doesn't exist anymore
- collapse ArmStateMachine into commander
- all requests already go through Commander::arm() and Commander::dismarm()
- other minor changes
- VEHICLE_CMD_DO_FLIGHTTERMINATION undocumented (unused?) test command (param1 > 1.5f) removed
- switching to NAVIGATION_STATE_TERMINATION triggers parachute command centrally (only if armed)
---------
Co-authored-by: Matthias Grob <maetugr@gmail.com>
If at the last powercycle one mission was uploaded, the counter in dataman was 1. On the next powercycle the mavlink mission counter was reset to zero and on first mission upload updated to 1 again. Other modules check, if the mission was changed based on the counter, like the mission.cpp loaded the mission counter from the dataman. On a new mission, the comparison of the counters failed, because both were the same value even if the mission was completely different.
It turns out that I had omitted implementing the gimbal_device_id which
is the component ID of the gimbal device that the gimbal manager (in
this case PX4) is responsible for.
Signed-off-by: Julian Oes <julian@oes.ch>
Camera controls should not happen through the flight controller, and
the control allocation has no means of controlling the camera zoom.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
When requesting a message from a stream that is not active we start the
stream with interval=0 and call the request method once. For all streams
this works fine except the gps_global_origin. For this one the request method
is actually overidden to throttle down the rate and not just send out the message.
This will cause this message to never being sent on request if the stream
is not active by default.
Prior commit added opening of /dev/null as 0, 1 and/or 2 file
descriptors, if they where not present. However, if the temporary
file descriptor used to open /dev/null matched the target file
descriptor, it would be immediately closed again. This commit fixes that,
and does not duplicate and close the temporary file descriptor if it is
already at the correct number.
If 0, 1 and/or 2 file descriptors are not open when mavlink module
starts (as might be the case for USB auto-start), use default /dev/null
so that these numbers are not used by other other files.
Instead of interpret a request for "more logs than currently exists" as
a new request, use a request for index 0, which is more likely to be
the first request.
Konrad