If the measured voltage is more than 65v we need to split the voltage
over multiple cells in order to avoid overflowing the uint16. This is
according to the MAVLink spec.
Signed-off-by: Julian Oes <julian@oes.ch>
The extension fields need to be 0 by default according to the MAVLink
spec. This is because extensions are 0 by default and need to be 0 when
unknown/unused for backwards compatibility.
The patch also simplifies the flow slightly in that it doesn't create a
temporary array but just fills in the cell voltages directly.
Signed-off-by: Julian Oes <julian@oes.ch>
- since last_us is set to 0 every time the bias is not observable, the
total time was also reset -> needed 30 consecutive seconds in mag 3D
to be declared "stable"
- after landing, the mag_aligned_in_flight flag is reset. Using this for
bias validity makes it invalid before we have a chance to save it to
the calibration.
Opt flow raw innovations can be really large on ground due to the small
distance to the ground (vel = flow / dist). To make the pre-flight check
more meaningful, scale it with the current distance.
This allows PWM and all other output methods to configure
stopped, idling and full thrust points and use them consistently.
The fact that a fixed wing motor can be stopped when zero thrust
is demanded is explicit and could in principle even be disabled.
The mechanism is the same as for a standard VTOL stopping the
multicopter motors in the fixed wing flight phase.
This allows to consistently define:
Motor stopped - disarmed PWM
Motor idling - minimum PWM
Motor at full thrust - maximum PWM
Any allocation can then distinctly decide if
a motor should be running or not depending
on the context and also explicitly command that.
When switching into Hold mode establish a Loiter around current position,
even if we were before already loitering (eg in Mission mode).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* uavcan rtcm set max num injections
* Subscribe to all instances of gps_inject_data and mirror uavcan rtcm pub mirror gps driver
* Minor logic refactor in gps and uavcan gps inject data
Before this the ESC calibration aborts if battery detection doesn't work.
The problem is if the user still connects the battery as he gets instructed
and the calibration aborts then the ESCs are in calibration mode and
after abortion calibrate to the wrong value.
Also I realized there's no additional safety by aborting the calibration
if the battery cannot be detected during the timeout because a pixhawk
board without power module will report a battery status from the
ADC driverand in it that no battery is connected which is the best
it can do. In this situation the motors will still spin if the
ESCs are powered.
Some ESCs e.g. Gaui enter the menu relatively quickly if the
signal is high for too long. To solve that it's kept high shorter.
Also all tested ESCs detect the low signal within a shorter time
so no need to wait longer.
- Change timings for a more reliable calibration.
- Make sure there's an error message when battery measurement is not
available also when it gets disabled after system boot in the power
just above the calibration button.
- Safety check if measured electrical current goes up after issuing the
high calibration value for the case the user did not unplug power
and the detection either fails or is not enforced.
This adds support for the TI LP5562 RGB LED driver.
Things to note:
- The driver is initialized in simple PWM mode using its internal clock,
for R,G,B, but not for W(hite).
- The chip doesn't have a WHO_AM_I or DEVICE_ID register to check.
Instead we read the W_CURRENT register that we're generally not using
and therefore doesn't get changed.
- The current is left at the default 17.5 mA but could be changed using
the command line argument.
Datasheet:
https://www.ti.com/lit/ds/symlink/lp5562.pdf
Signed-off-by: Julian Oes <julian@oes.ch>
The entire logic did not work for the case when the throttle channel is
reversed because then QGC sets trim = max for that channel and
the result is only half the throttle range.
