Use kClearanceAltitudeBuffer for it, which is also used to ensure that during takeoff an
altitude setpoint above the clearance altitdue is set.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- also put flaring internal states into a struct to organize a bit
- one concern with blending the throttle setpoint like this with the flare time param is that folding prop belly landing airframes may want to have a separate param for shorter throttle kill and still use the flare time ramps for everything else
TECS climbout mode was used for takeoff climbout, which puts throttle to full and does not regulate a specific airspeed.
This commit sets the desired takeoff airspeed explicitly and allows max climb rate to track the ascent.
previously a scale factor param on min airspeed was used to define the climbout airspeed for runway takeoff
additionally, the rotation speed was defined by another hardcoded scale on top of the previously scaled min airspeed
this commit explicitly defines a takeoff speed and rotation speed for runway takeoff in params, with option to disable
Instead of checking the .valid flag of position_setpoint, check for ISFINITE() of lat, lon, alt
when pulling the position_setpoint triplet. This fixes problems where the .valid flag didn't
reflect the proper state of the setpoint (e.g. .valid was true, .lat though NAN)
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- msg constant names now comply with ROS conventions:
uppercase alphanumeric characters with underscores for separating words
partially fix#19917
Signed-off-by: Beniamino Pozzan <beniamino.pozzan@phd.unipd.it>
- new param, FW_LND_TER_REL
- fixing the glide slope helps keep the landing glide behavior steady (avoiding bumps in the altitude setpoint from e.g. trees)
- flare is still triggered via the distance sensor, if enabled by FW_LND_USETERR
- the target_sink_rate param could possibly constrain the maximum commanded sink rate to something less than that of the landing glide slope, which would make it impossible to track. this commit allows opening up the desired max sink rate up to the performance limits of the aircraft, if necessary, for the landing case
- landing slope/curve library removed
- flare curve removed (the position setpoints will not be tracked during a flare, and were being ignored by open-loop maneuvers anyway)
- flare curve replaced by simply commanding a constant glide slope to the ground from the approach entrance, and commanding a sink rate once below flaring alt
- flare is now time-to-touchdown -based to account for differing descent rates (e.g. due to wind)
- flare pitch limits and height rate commands are ramped in from the previous iteration's values at flare onset to avoid jumpy commands
- TECS controls all aspects of the auto landing airspeed and altitude/height rate, and is only constrained by pitch and throttle limits (lessening unintuitive open loop manuever overrides)
- throttle is killed on flare
- flare is the singular point of no return during landing
- lateral manual nudging of the touchdown point is configurable via parameter, allowing the operator to nudge (via remote) either the touchdown point itself (adjusting approach vector) or shifting the entire approach path to the left or right. this helps when GCS map or GNSS uncertainties set the aircraft on a slightly offset approach"
- post takeoff, the aircraft follows the infinite line sourced from the launch point in the direction of the takeoff waypoint
- takeoff waypoint altitude is used as a clearance altitude, set such that once above, the aircraft has cleared all ground occlusions and may proceed with the mission
- runway takeoff state machine simplified to throttle ramp, clamped to runway, climbout, and fly
- throttle ramp must complete before switching to next state to avoid a jump in throttle setpoint just after takeoff if the takeoff airspeed is reached before the ramp is complete
- roll constraints near ground post takeoff removed from runway takeoff class (handled externally now)
- minimum airspeed in TECS is reduced to takeoff speed (if necessary) to lower the underspeed detection bound
- lateral-directional guidance uses a different period parameter during ground roll
- apply constraint only for takeoff and landing modes
- add two params, wing span and wing height, to calculate a reasonable height at which roll limits can be opened
- takeoff situational knowledge removed from all other modes except manual (or actual takeoff mode)
- manual takeoff is marked complete if at a controllable airspeed
- minimum pitch bounds TECS until manual takeoff complete
- remove individual roll constraints during manual takeoff (ground proximity constraints coming in subsequent commit)
- create integral and trajectory generator reset methods
- always run TECS unless in rotary-wing mode (or in transition)
- constantly reset TECS integrals and trajectory generators when landed
- simplify takeoff reset method
- removes _last_manual variable in favor of _skipping_takeoff_detection, which is handled in the control mode setter
- takeoff detection (both launch and runway) is skipped if entering takeoff mode from any other mode while having already been in the air
- added method to runway takeoff class for force setting the fly state when we want to skip the takeoff detection
- trim throttle is handled entirely by the position controller
- navigator should use speed setpoints
- added flag gliding_enabled in position setpoint to stills support gliding
Signed-off-by: RomanBapst <bapstroman@gmail.com>
- allow compensation based on vehicle weight (parameterized)
- use density for calculating trim throttle compensation instead of pressure
- removed parameter FW_THR_ALT_SCL
Signed-off-by: RomanBapst <bapstroman@gmail.com>
- documentation of units, params, returns, and descriptions for variables and methods
- rename ambiguous or erroneous state variables
- remove unused or unecessary input arguments to functions
- remove ugly header white space
-rename FW_POSCTL_INV_ST to FW_POS_STK_CONF and make bitmask out of it:
- bit 0: alternative mapping (height rate on throttle stick, airspeed on pitch)
- bit 1: enable/disable airspeed setpoints via stick
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- if following line segment (fixed-wing position control) switch waypoint when in acceptance radius OR passed the second waypoint. this handles the case of being beyond the second waypoint but not within the acceptance radius without the need to fly back to the waypoint (e.g. after a loiter up to waypoint alt)
- sync navigator and fw pos ctrl waypoint acceptance altitude
- introuce slew rate limiting of airspeed setpoint (with slew rate of 1 m/s/s)
- some refactoring and clean up
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Silvan Fuhrer