* Bidirectional DShot
Co-authored-by: Julian Oes <julian@oes.ch>
* f4/f1 support, not supported
* fix f1 build target
* sanity check timer_channel value, fix CCxNP ifdef, debug stuff
* removed debug code, added define for H7 HAVE_GTIM_CCXNP
* round robin sampling for less than 4 DMA
* unlimited esc_status logging
* dshot: fix formatting
* dshot: add define for number of DMA channels to use
This allows individual boards to override the number of DShot channels
and hence avoid round robin capture of the RPM feedback.
* ARK: enable 4 DMA channels for DShot on 6X
* dshot: publish when all channels are updated
This slows down the ESC_STATUS publication in the case of round robin
capture. E.g. for 800 Hz output with one DMA channel, the ESC_STATUS is
now published at 200 Hz.
* dshot: avoid duplicate publications for bidir and telem
Instead of publishing both bidirectional dshot updates as well as
telemetry updates, we now combine the data from both streams, and
publish whenever we get RPM updates, as the latter arrives with higher
rate, e.g. 200 Hz with round robin, or faster otherwise.
When combining the data, we take RPM from bidirectional dshot, and the
rest from telemetry.
When we have only one of the two, either telemetry or bidirectional
dshot, we just publish that one.
* boards: add ark fpv and pi6x BOARD_DMA_NUM_DSHOT_CHANNELS
* dshot: turn off debug build
---------
Co-authored-by: Julian Oes <julian@oes.ch>
Co-authored-by: alexklimaj <alex@arkelectron.com>
Internal combustion engine control module.
New actuator functions and RPM based start/restart logic.
Not enabled by default.
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Co-authored-by: Pernilla <pernilla@auterion.com>
move init_logfile_encryption() call after the buffer start_log() call
to have log file already open while storing the header and key data to
the beginning of the file.
* SDLOG_ALGORITHM - AES option not implemented
* Update src/modules/logger/params.c
Co-authored-by: Daniel Agar <daniel@agar.ca>
---------
Co-authored-by: Daniel Agar <daniel@agar.ca>
Improve the slow down effect and add support for speed change in mission mode.
Seperate code related to turning setpoints into motor commands into its own folder and refactor code.
- new parameter EKF2_LOG_VERBOSE to enable (currently enabled by default)
- force advertise topics immediately (based on EKF2_LOG_VERBOSE and per aid source configuration)
- logger optionally log all estimator topics at minimal rate
* battery: make time remaining estimation dependent on level flight characteristis for FW
* battery: fix that FW flight is also correctly detected when vehicle_status is not updated
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* FixedwingPositionControl: Move constant to header file
* flight phase estimation: use tecs height rate reference to check for level flight
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
When the CPU load monitor is started while already running, then the
idle thread last_times[0] is reset to the last 1 second, rather than
since when the CPU load monitor was last started. The remaining threads
are not impacted, since their last_times[i] is reset to zero here.
This results in the idle thread having a lower than real CPU load, with
the remaining CPU time being wrongly attributed as scheduler load.
- fake_pos only if at rest or tilt variances becomes large
- fake pos: don't run when grav fusion is enabled
- gravity fusion enabled by default
- gravity: only fuse when accel norm and lpf norm are consistent
Co-authored-by: bresch <brescianimathieu@gmail.com>
Jacob Dahl