- remove all remaining IOCTLs for accel and gyro and handle all calibration entirely in sensors module with parameters
- sensor_accel and sensor_gyro are now always raw sensor data
- calibration procedures no longer need to first clear existing values before starting
- temperature calibration (TC) remove all scale (SCL) parameters
- gyro and baro scale are completely unused
- regular accel calibration scale can be used (CAL_ACC*_xSCALE) instead of TC scale
Greatly improves the noise on the d-term on a Kopis 2. Apparently the order
of filtering vs differentiating matters.
Also disables the DGYRO filter by default, as the D-term now already has
a default filter of 30Hz applied.
- IMU integration move from drivers (PX4Accelerometer/PX4Gyroscope) to sensors/vehicle_imu
- sensors: voted_sensors_update now consumes vehicle_imu
- delete sensor_accel_integrated, sensor_gyro_integrated
- merge sensor_accel_status/sensor_gyro_status into vehicle_imu_status
- sensors status output minor improvements (ordering, whitespace, show selected sensor device id and instance)
The timestamp actually used by ekf2 is the sensor_combined timestamp, so we should be setting it with the actual data sample timestamp, rather than the aggregated sensors topic publication metadata.
Later the sensor_combined message will be replaced with vehicle_imu that carries a separate publication timestamp and raw sample timestamp.
- create common uORB::PublicationBase
- uORB::PublicationQueued types are now type aliases
- ORB_PRIO use enum type everywhere to avoid accidental misuse
- PX4Accelerometer/PX4Gyroscope/etc driver libs explicitly advertise on construction, unadvertise on destruction. This is a workaround for any potential issues that might appear when accel/gyro cdev and uORB indexing doesn't align.
Running the sensors module out of the same WQ thread as the estimator, position, and attitude controllers is a bit safer and prevents potential priority and starvation issues. There is a very small increase in latency (~50 us) between sensors and ekf2 execution (on average). This also saves a little bit of memory (~ 3 kB) and cpu (~1-1.5% depending on the board).
I've added a queue depth of 4 for sensor_accel and sensor_gyro. This is initially added because it's not always possible for the `vehicle_acceleration` to keep up with every publication of the primary accelerator as it runs in the same thread as ekf2, various controllers, etc.
Later this mechanism will be used in a few areas
- rate limit `vehicle_angular_velocity` and `vehicle_acceleration` without missing any raw data
- move IMU integration to `vehicle_imu` and out of the actual driver threads, eliminating the need for sensor_accel_integrated and sensor_gyro_integrated
- integrate raw gyro synchronized with optical flow measurements
- introduces parameter IMU_DGYRO_CUTOFF to configure the angular acceleration low pass filter
- the angular acceleration is computed by differentiating angular velocity after the notch filter (IMU_GYRO_NF_FREQ & IMU_GYRO_NF_BW) is applied
Co-authored-by: Julien Lecoeur <jlecoeur@users.noreply.github.com>
- gyro filtering (low-pass and notch) only performed on primary gyro in `sensors/vehicle_angular_velocity` instead of every gyro in `PX4Gyroscope`
- sample rate is calculated from actual updates (the fixed value was slightly wrong in many cases, and very wrong in a few)
- In the FIFO case the array is now averaged and published in `sensor_gyro` for filtering downstream. I'll update this in the future to use the full FIFO array (if available), but right now it should be fine.
- this is a new module for temperature compensation that consolidates the functionality previously handled in the sensors module (calculating runtime thermal corrections) and the events module (online thermal calibration)
- by collecting this functionality into a single module we can optionally disable it on systems where it's not used and save some flash (if disabled at build time) or memory (disabled at run time)
- split out integrated data into new standalone messages (sensor_accel_integrated and sensor_gyro_integrated)
- publish sensor_gyro at full rate and remove sensor_gyro_control
- limit sensor status publications to 10 Hz
- remove unused accel/gyro raw ADC fields
- add device IDs to sensor_bias and sensor_correction
- vehicle_angular_velocity/vehicle_acceleration: check device ids before using bias and corrections
The bulk of this change was tightly coupled and needed to be deleted in one pass. Some of the smaller changes were things that broke as a result of the initial purge and subsequently fixed by further eradicating unnecessary platform differences. Finally, I deleted any dead code I came across in the related files I touched while going through everything.
- DriverFramework (src/lib/DriverFramework submodule) completely removed
- added dspal submodule in qurt platform (was brought in via DriverFramework)
- all df wrapper drivers removed
- all boards using df wrapper drivers updated to use in tree equivalents
- unused empty arch/board.h on posix and qurt removed
- unused IOCTLs removed (pub block, priv, etc)
- Integrator delete methods only used from df wrapper drivers
- commander: sensor calibration use "NuttX version" everywhere for now
- sensors: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- battery_status: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- cdev cleanup conflicting typedefs and names with actual OS (pollevent_t, etc)
- load_mon and top remove from linux boards (unused)
- delete unused PX4_MAIN_FUNCTION
- delete unused getreg32 macro
- delete unused SIOCDEVPRIVATE define
- named each platform tasks consistently
- posix list_devices and list_topics removed (list_files now shows all virtual files)
* NotchFilter: add NotchFilter template and test for float type
* NotchFilterTest: add test for Vector3f notch filter
* PX4Gyroscope: add notch filter with IMU_GYRO_NF_(FREQ|BW) parameters to
set the notch center frequency and bandwidth
Beat Küng