56 Commits

Author SHA1 Message Date
Matthias Grob
9156c5c065 ROMFS: remove single trailing zeros 2024-01-09 10:27:39 +01:00
Silvan Fuhrer
29807a5e50 Replace CBRK_AIRSPD_CHK with SYS_HAS_NUM_ASPD
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
2023-12-21 11:34:28 +01:00
Silvan Fuhrer
88bf18a2fe airframe configs: remove custom tuning if close to param default and not required due to hardware
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
2023-04-19 10:22:10 +02:00
Silvan Fuhrer
4d2a31afe3 Navigator: remove max distance between WP mission feasibility check (MIS_DIST_WPS)
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
2023-03-27 17:43:33 +02:00
Silvan Fuhrer
9b3a28dff5 Commander: add local_position_accuracy_low flag, incl. warning and RTL
Set this flag to true if local position is valid but accuracy low, such that
the operator can be warned before system switches to position-failure failsafe.
Additionally, switch to RTL if currently in Mission or Loiter to try to reach home
or fly out of GNSS-denied area.

Set low accuracy threshold to 50m by default for FW and VTOL.

Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
2023-02-01 16:47:11 +01:00
Silvan Fuhrer
3ca126cc46 Commander: improve description of COM_FS EPH, EPV, VEL_EVH params and increase FW and VTOL defaults
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
2023-02-01 16:47:11 +01:00
Silvan Fuhrer
4cd7dfa162 MissionFeasibility: add combined takeoff/landing requirement check
Replace the existing check for the availability of a takeoff mission item with a combined
check for takeoff and landing item (or landing pattern). New param MIS_TKO_LAND_REQ
can be set to require only a takeoff, only a landing, both takeoff and landing, and
both or none. The latter is meant to be set if is e.g. deemed unsafe to start a flight
through a Takeoff WP without though defining a Landing - as then in case of a RTL the
vehicle doesn't follow a pre-defined path but instead only can do default RTL that especially
for FW and VTOL isn't always safe.

Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
2022-11-21 18:03:21 +01:00
Daniel Agar
55be169e18 delete remaining PWM_MAIN/PWM_AUX/PWM_EXTRA parameters 2022-09-09 09:14:09 -04:00
Silvan Fuhrer
6ebc88fed7 ROMFS: vtol_defaults: reduce aggressiveness around roll and yaw axis
For most VTOLs the param defaults for the agressiveness of the MC attitude controller
are too high, as VTOLs usually have high intertia and lot af drag due to wings and
can thus not rotate as fast as MCs.

Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
2022-08-05 14:11:59 +02:00
Silvan Fuhrer
828992adf7 increase default of MPC_Z_VEL_MAX_DN and MPC_Z_V_AUTO_DN from 1 to 1.5
I think most vehicle can safely decend with at least 1.5m/s, and having this
value too low makes Descents/Landings/RTLs unnecessary long.

Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
2022-08-05 14:11:59 +02:00
Silvan Fuhrer
c42667ac64 ROMFS: vtol_defaults: remvoe custom NAV_ACC_RAD, leave at param default (10)
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
2022-08-05 14:11:59 +02:00
Silvan Fuhrer
4614c1a0b4 ROMFS: vtol_defaults: increase default hover speeds
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
2022-08-05 14:11:59 +02:00
Silvan Fuhrer
0d10491b89 ROMFS: vtol_defaults: remove MPC_TKO_SPEED from VTOL defaults
The VTOL default was set to 1, while the param default is 1.5.
I don't see why it shuold be a different default for VTOLs and thus remove it.

Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
2022-08-05 14:11:59 +02:00
Daniel Agar
98623f69a3 update mavlink submodule to latest
- update MAV_TYPE VTOL usage for current mavlink
2022-04-07 20:35:41 +02:00
Daniel Agar
36e6527013 ROMFS: MAV_TYPE cleanup
- set MAV_TYPE as a parameter default per vehicle type, or airframe if necessary
 - cleanup MAV_TYPE param metadata and commander helper to only include
what's currently used in PX4
2022-03-17 09:28:10 -04:00
bresch
76615f8df3 VTOL: set HTE horizontal speed sensitivity threshold low 2021-09-25 20:07:28 -04:00
Yannick Fuhrer
759a60ac82 Update rc.vtol_defaults
based on our experience with VTOL it makes sense to change the yaw mode default. You always want your VTOL to yaw in transition direction before starting the transition.
2021-05-01 10:45:14 -04:00
Daniel Agar
c9a2d0ed34 IMU_GYRO_RATEMAX set system default to 400 Hz
- MC default is still 800 Hz
2021-03-02 10:08:49 -05:00
Daniel Agar
b67aa77d29 ROMFS: use new param default mechanism 2021-02-12 08:27:47 -05:00
bresch
72e34e02ef VTOL defaults: increase tracking tolerance for VTOL planes 2021-02-05 20:13:30 +01:00
Daniel Agar
d1a3590aac PWM: transition PWM_{MIN,MAX,DISARMED,RATE} -> PWM_MAIN 2021-02-01 08:53:33 +01:00
Silvan Fuhrer
195a900ecf change default of RTL_LAND_DELAY to 0
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
2021-01-17 12:05:30 +01:00
Silvan Fuhrer
037c821142 ROMFS: increase max distance between waypoints for VTOL and FW to 5km
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
2021-01-17 12:05:30 +01:00
Silvan Fuhrer
5382d3b8fb rc.VTOL_defaults: enable wind estimation in EKF by default and remove MPC_LAND_SPEED being, as it's just set to param default
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
2020-11-26 08:50:49 +01:00
Matthias Grob
bda072512a rc.vtol_defaults: reduce maximum jerk to 4.5 m/s³ based on testing feedback
@fury1895 reported very valuable feedback from testing
the acceleration feed-forward on VTOL:
> MPC_JERK_MAX 4.5 (from 5 on it felt too aggressive)
> MPC_JERK_AUTO 4
> some hovering, some transitions, and a mission. Everything good.
> I'd say you feel the difference in position mode and you see it in
> Auto modes. Great improvement!
2020-03-30 09:58:39 +02:00
Daniel Agar
bde36f0f4a
ROMFS: rc.vtol_defaults limit inner loop rate (#13196)
- temporary remedy for https://github.com/PX4/Firmware/issues/13149
2019-10-16 12:27:06 -04:00
Silvan Fuhrer
536f073d02 VTOL: set RTL_TYPE default for VTOL to 1 (return to home via mission landing if available) 2019-08-21 10:15:06 +02:00
Silvan Fuhrer
9b46c1d8a9 Upated Babyshark VTOL config and vtol_defaults
Updated the babyshark default  parameters for improved flight performance,
as well as two MPC parameters in vtol_defaults for smoother hovering with VTOLS"

Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
2019-07-04 11:26:01 -04:00
Julian Oes
3ebf030a02 ROMFS: change shebang from #!zsh to #!/bin/sh
This was required for shellsheck.
2018-12-19 07:36:43 +00:00
Daniel Agar
3a036021ba ROMFS defaults drop floating point decimal 2018-12-04 22:57:53 -05:00
Beat Küng
37338e442f NuttX shell scripts: replace operator == with =
- NuttX supports both versions
- POSIX shell only supports '='
2018-09-27 23:39:20 +02:00
Roman
e1992a5036 ROMFS: enable weathervane by default for VTOL
Signed-off-by: Roman <bapstroman@gmail.com>
2018-09-19 13:30:32 -04:00
mcsauder
0d0fcb140c Updated rc.vtol_defaults to correct PWM_AUX behavior for VTOL airframes. Added PWM_AUX_RATE to rc.vtol_default and set parameters directly instead of environment variables. 2018-09-17 20:28:09 -04:00
mcsauder
4ea3306ec2 Set parameters directly rather than script variables in VTOL airframe config files and alphabetize lists. 2018-09-04 10:23:27 +02:00
mcsauder
2512f6e30e Format and comment fw, mc, vtol, and ugv vehicle apps and default startup scripts. 2018-07-13 11:02:26 +02:00
Daniel Agar
28d1ec8afe
VTOL defaults set MIS_TAKEOFF_ALT 20 and remove tuning (#8481) 2017-12-17 00:58:23 -05:00
Matthias Grob
bfb4de0e66 startup scripts/mc_pos_control: renamed parameters after refactor 2017-03-22 15:21:34 +01:00
Lorenz Meier
73689e65ee Update VTOL setup for PWM outputs 2016-12-13 09:18:59 +01:00
Daniel Agar
6d655d2d6e startup remove old EKF PE_ params (#5533) 2016-09-26 22:51:43 +02:00
Mark Whitehorn
545152f676 remove "transitional support" (#5378) 2016-08-24 23:05:39 +02:00
Andreas Antener
433eeb3d09 make landing in RTL default for VTOL capable vehicles 2016-04-21 09:32:33 +02:00
tumbili
7d893703d7 ensure suitable PWM min/max/disarmed param values for multirotor and vtol 2016-03-01 09:45:42 +01:00
tumbili
457dc6a0a4 vtol defaults: use parameters for pwm values 2016-03-01 09:36:23 +01:00
sander
9b03854fda Change MPC_ACC_HOR_MAX default to 2.0 2016-02-28 15:57:21 +01:00
Andreas Antener
770c020117 removed lower default from vtol config, added flight tested Fun Cub parameters 2016-02-17 10:49:28 +01:00
Andreas Antener
570fb97163 updated timeout logic to work only on waypoints with forced headings, updated param docs accordingly 2016-02-15 23:29:47 +01:00
Andreas Antener
eb5b8a32ee transition alignment will force heading now and go to RTL if it cannot reach it in time, handle mission failure correctly, reset after mission update, issue message with actual problem 2016-02-15 23:29:38 +01:00
Andreas Antener
bb4decfa8b implemented basic heading timeout for waypoint acceptance, added parameter for yaw error on waypoint heading acceptance, set yaw timeout for vtol default 2016-02-15 23:26:28 +01:00
Andreas Antener
4e0559eacf updated mpc parameters for sitl standard vtol 2016-02-08 11:09:12 +01:00
Andreas Antener
e2328fcd72 use default acceptance radius for takeoff in MC case, set VTOL radius to 3 2016-02-08 11:09:11 +01:00