* Creating a base for grf lidar
* Serial Drive is working, need to work out distance publish
* WIP Getting Range Data in cm
* Working Rand Distance Values for GRF 250 and GRF500
* Review Changes
* Compiler fixes
* Update to date
* small update
* Fix typo and remover unused libs
* removing unused enum
* Update to the Documentation
* Fiving scaling issue
* update to the logic
* [Feature] Adding I2C driver for the GRF250 and GRF500 models (#26425)
* Adding the GRF I2C driver
* I2C Driver Working
* Removing a lot of unnecessary code
* fixing names
* Changing the i2c Driver to be in the lightware laser
* remove the old driver
* formatting fix
* Adding Ligthware GRF to documentation
* Update to the Documentation
* Ensuring sample_perf ends
* Updating Docs
* uavcannode: implement hardpoint commands (#26334)
* implement cannode hardpoint commands
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
* Update src/drivers/uavcannode/Subscribers/HardpointCommand.hpp
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Update src/drivers/uavcannode/Subscribers/HardpointCommand.hpp
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* add hardpoint sub to ark cannode, simplify handling of hardpoint broadcast
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
---------
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* voxl_esc: Limit frequency of UART passthru writes to 20Hz
* voxl2_io: Added UART passthru
* docs: update link for px4 ros2 interface lib python api docs
* estimator_interface: remove unused getter
* gnss_checks: always run strict checks on ground
With the goal to never take off if the GNSS solution is not fullfilling the configured requirements still not stopping to use it in case it degrades mid air.
* ekf2 unit-tests: adapt to strict GNSS checks on ground
* escCheck: rework online check to properly report offline ESCs
previous to this
09d79b221f
set `esc_online_flags` e.g. for UAVCAN ESCs which specific one is online and that then got compared to a mask where the first `esc_count` bits were set.
So if only ESC 5 is mapped and online you get the message "ESC 156 offline" because `esc_online_flags = 0b1000` gets compared to `online_bitmask = 0b1` based on `esc_count = 1` and the motor index is `esc[0].actuator_function = 0` wrapped using `0 - actuator_motors_s::ACTUATOR_FUNCTION_MOTOR1 + 1 = 156`.
* FailureDetector: consistent timestamp naming
* FailureDetector: rework motor status check
* FailureDetector: implement upper and lower current limit with offset
* Update src/modules/commander/failure_detector/FailureDetector.cpp
Prevent Buffer overflow
* Update Format
* Subedit
* Shrink and rename image
* Apply suggestion from @hamishwillee
Sounds good
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Apply suggestion from @hamishwillee
More universal approach
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Update to the Documentation
* FailureDetector: rework motor status check
* FailureDetector: implement upper and lower current limit with offset
* Subedit
* docs: update parameter reference metadata
* Remove pregenerated files - that should all be tidied up next time this runs
* remover GRF parameters
* Documentation updates
* Fixing Merge Conflicts
* remove @
* Undo Changes to parameter_reference
* remove the code that will be autogen-ed
* Update the Camake File
---------
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
Co-authored-by: Andrew Brahim <35986980+dirksavage88@users.noreply.github.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
Co-authored-by: Eric Katzfey <eric.katzfey@modalai.com>
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
Co-authored-by: Matthias Grob <maetugr@gmail.com>
Co-authored-by: Marco Hauswirth <marco.hauswirth@auterion.com>
Co-authored-by: Nick <145654544+ttechnick@users.noreply.github.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
- split up old module into two, one handling setpoint generation, one control
- add lateral and longitudinal control setpoints topics that can also be
injected from companion computer
- add configuration topics that (optionally) configure the controller
with limits and momentary settings
Signed-off-by: RomanBapst <bapstroman@gmail.com>
Signed-off-by: Silvan <silvan@auterion.com>
boards: increase max mission items for boards with >=1kb RAM to 1000
Signed-off-by: Silvan <silvan@auterion.com>
boards: increase NUM_MISSION_ITMES_SUPPORTED for SITL to 10000
Signed-off-by: Silvan <silvan@auterion.com>
* add sf45 driver to 6xrt
* disable the sf45 driver on rover, since collision prevention is tied with MPC params
---------
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
* usb: Added parameter to enable always starting mavlink on USB.
Refactored cdcacm_init into a module and added a paramter to allow always starting mavlink on
USB, also added a paramter to choose the mode. The current default behavior is to wait and listen
for data on USB and auto-detect the protocol (mavlink, nsh, ublox). This results in the mavlink
stream not starting until something else on the mavlink network sends a packet first. The new
default behavior is to always start mavlink.
Added parameters
MAV_USB_ENABLE -- default 1 (always start mavlink on USB)
MAV_USE_MODE -- default 3 (onboard)
* added 3 retries for opening serial port in mavlink, removed sleep before sercon
* added DRIVERS_CDCACM_AUTOSTART to ark-v6x default.px4board
* added CONFIG_DRIVERS_CDCACM_AUTOSTART=y to default.px4board for boards with CONFIG_CDCACM in their nsh/defconfig
* format
* remove PGA460 from COMMON_DISTANCE_SENSOR to save flash
* remove LIS2MDL from COMMON_MAGNETOMETER to save flash
* disable CONFIG_DRIVERS_CDCACM_AUTOSTART for fmu-v5 protected.px4board
* moved and renamed parameters, removed mode logic in mavlink
* changed parameter names, added mode none
* remove parameters from mavlink
nxp/rt117x:Fix Pin IRQ
nxp/rt117x:Support 4 i2c busses
nxp/rt117x:Add px4io_serial support
nxp/imxrt:Expand ToneAlarmInterface to GPT 3 & 4
px4_fmu-6xrt:Using imxrt_flexspi_nor_octal
px4_fmu-6xrt:Entry is start
px4_fmu-6xrt:Add Proper MTD
px4_fmu-6xrt:Set I2C Buses
px4_fmu-6xrt:Proper SPI usage
px4_fmu-6xrt:Adjust memory Map to use the 2 MB
px4_fmu-6xrt:Bring in ROMAPI
px4_fmu-6xrt:Push FLASH to 200Mhz
px4_fmu-6xrt:Use BOARD_I2C_LATEINIT
px4_fmu-6xrt:Clock Config remove unused devices
px4_fmu-6xrt:Remove EVK SDRAM IO
px4_fmu-6xrt:Enable SE550 using HW_VER_REV_DRIVE
px4_fmu-6xrt:Use MTD to mount FRAM on Flex SPI
px4_fmu-6xrt:Manifest
px4_fmu-6xrt:Restore board_peripheral_reset
px4_fmu-6xrt:Set I2C buss Interna/Externa and startup
nxp/rt117x:Set 6 I2C busses
px4_fmu-6xrt:Correct Clock Sources and Freqency Settings
px4_fmu-6xrt:Correct ADC Settings
px4_fmu-6xrt:Tune FlexSPI config and sync header with debug variant Linker prep for rodata ahb partitioning
px4_fmu-6xrt:FlexSPI prefetch partition split .text and .rodata
Current config
1KB Prefetch .rodata
3KB Prefetch .text
px4_fmu-6xrt:Run imxrt_flash_setup_prefetch_partition from ram with barriers
px4_fmu-6xrt:Use All OCTL setting from FLASH g_flash_config SANS lookupTable
px4_fmu-6xrt:Octal spi boot/debug problem bypass
px4_fmu-6xrt:Add PWM test
px4_fmu-6xrt:Fix clockconfig and USB vbus sense
px4_fmu-6xrt: Use TCM
px4_fmu-6xrt: Ethernet bringup
imxrt: use unique_id register for board_identity
px4_fmu-6xrt: update ITCM mapping, todo proper trap on pc hitting 0x0
px4_fmu-6xrt:correct rotation icm42688p onboard imu
rt117x: Add SSARC HP RAM driver for memory dumps
px4_fmu-6xrt: Enable hardfault_log
px4_fmu-6xrt: Enable DMA pool
px4_fmu-6xrt: fix uart mapping
px4_fmu-6xrt: enable SocketCAN & DroneCAN
px4_fmu-6xrt:Command line history TAB completion
px4_fmu-6xrt:Fix pinning duplication
px4_fmu-6xrt:Support conditional PHY address based on selected PHY
px4_fmu-6xrt:Add Pull Downs on CTS, use GPIO for RTS
px4_fmu-6xrt:Set TelemN TX Slew rate and Drive Strenth to max
px4_fmu-6xrt::Set TELEM Buffers add HW HS
px4_fmu-6xrt:Turn off DMA poll
px4_fmu-6xrt:RC_SERIAL_PORT needed to be px4io to disable rc_input using TELEM2!
px4_fmu-6xrt: bootloader (#22228)
* imxrt:Add bootloader support
* bootloader:imxrt clear BOOT_RTC_SIGNATURE
* px4_fmu-6xrt:Add bootloader
* px4_fmu-6xrt:bootloader removed ADC
* px4_fmu-6xrt:bootloader base bootloader script off of script.ld
* px4_fmu-6xrt:add _bootdelay_signature & change entry from 0x30000000 to 0x30040000
* px4_fmu-6xrt:hw_config Bootloader has to have 12 bytes
px4_fmu-6xrt:Default to use LAN8742A PHY
px4_fmu-v6xrt:VID Set to Drone Code
board_reset:Enable ability to write RTC GP regs
px4_fmu-6xrt:Fix CMP0079 error
rt117x:micro_hal Add a PX4_MAKE_GPIO_PULLED_INPUT
px4_fmu-v6xrt:Set CTS High before VDD_5V applided to ports to avoid radios fro entering bootloaders
fmu-v6xrt: increase 5v down time
fmu-v6xrt:Ready for Release DEBUGASSERTS off and Console 57600,
Bootloder updated.
imxrt:board_hw_rev_ver Rework for 3.893V Ref
px4_fmu-v6xrt:Move ADC to Port3
