ORB queue depth completely static

We had a special handling for RTL triggered in vtol_takeoff state.
The idea is to wait until the VTOL Takeoff is completed and only
then switch to RTL. On a second thought this special handling isn't
really necessary and for the sake of simplicity should be removed.
This also removes the side effect of the indicated flight mode
after RTL being set to VTOL_Takeoff again.

Signed-off-by: Silvan Fuhrer <silvan@auterion.com>

.ci/Jenkinsfile-compile

@@ -120,7 +120,7 @@ pipeline {
                      "px4_fmu-v6xrt_rover",
                      "px4_io-v2_default",
                      "raspberrypi_pico_default",
-                     "siyi_n7_default"
+                     "siyi_n7_default",
                      "sky-drones_smartap-airlink_default",
                      "spracing_h7extreme_default",
                      "thepeach_k1_default",

.github/workflows/compile_nuttx.yml

@@ -25,6 +25,7 @@ jobs:
           ark_can-rtk-gps,
           ark_cannode,
           ark_fmu-v6x,
+          ark_septentrio-gps,
           atl_mantis-edu,
           av_x-v1,
           bitcraze_crazyflie,

.vscode/cmake-variants.yaml

@@ -151,6 +151,16 @@ CONFIG:
       buildType: MinSizeRel
       settings:
         CONFIG: ark_can-rtk-gps_canbootloader
+    ark_septentrio_gps_default:
+      short: ark_septentrio_gps_default
+      buildType: MinSizeRel
+      settings:
+        CONFIG: ark_septentrio_gps_default
+    ark_septentrio_gps_canbootloader:
+      short: ark_septentrio_gps_canbootloader
+      buildType: MinSizeRel
+      settings:
+        CONFIG: ark_septentrio_gps_canbootloader
     ark_cannode_default:
       short: ark_cannode_default
       buildType: MinSizeRel

ROMFS/px4fmu_common/init.d-posix/airframes/4011_gz_lawnmower

@@ -0,0 +1,80 @@
+#!/bin/sh
+# @name Gazebo lawnmower
+# @type Rover
+# @class Rover
+
+. ${R}etc/init.d/rc.rover_differential_defaults
+
+PX4_SIMULATOR=${PX4_SIMULATOR:=gz}
+PX4_GZ_WORLD=${PX4_GZ_WORLD:=default}
+PX4_SIM_MODEL=${PX4_SIM_MODEL:=lawnmower}
+
+param set-default SIM_GZ_EN 1 # Gazebo bridge
+
+# Simulated sensors
+param set-default SENS_EN_GPSSIM 1
+param set-default SENS_EN_BAROSIM 0
+param set-default SENS_EN_MAGSIM 1
+param set-default SENS_EN_ARSPDSIM 1
+# We can arm and drive in manual mode when it slides and GPS check fails:
+param set-default COM_ARM_WO_GPS 1
+
+# Set Differential Drive Kinematics Library parameters:
+param set RDD_WHEEL_BASE 0.9
+param set RDD_WHEEL_RADIUS 0.22
+param set RDD_WHEEL_SPEED 10.0	# Maximum wheel speed rad/s, approx 8 km/h
+
+# Actuator mapping - set SITL motors/servos output parameters:
+
+# "Motors" - motor channels 0 (Right) and 1 (Left) - via Wheels GZ bridge:
+param set-default SIM_GZ_WH_FUNC1 101 # right wheel
+#param set-default SIM_GZ_WH_MIN1 0
+#param set-default SIM_GZ_WH_MAX1 200
+#param set-default SIM_GZ_WH_DIS1 100
+#param set-default SIM_GZ_WH_FAIL1 100
+
+param set-default SIM_GZ_WH_FUNC2 102 # left wheel
+#param set-default SIM_GZ_WH_MIN2 0
+#param set-default SIM_GZ_WH_MAX2 200
+#aram set-default SIM_GZ_WH_DIS2 100
+#param set-default SIM_GZ_WH_FAIL2 100
+
+param set-default SIM_GZ_WH_REV 0 # no need to reverse any wheels
+
+# Note: The servo configurations ( SIM_GZ_SV_FUNC*) outlined below are intended for educational purposes in this simulation. 
+# They do not have physical effects in the simulated environment, except for actuating the joints. Their definitions are meant to demonstrate 
+# how actuators could be mapped and configured in a real-world application, providing a foundation for understanding and implementing actuator 
+# controls in practical scenarios.
+
+# Cutter deck blades clutch, PCA9685 servo channel 3,  "RC FLAPS" (406) - leftmost switch, or "Servo 3" (203):
+param set-default SIM_GZ_SV_FUNC3 203
+param set-default SIM_GZ_SV_MIN3 0
+param set-default SIM_GZ_SV_MAX3 1000
+param set-default SIM_GZ_SV_DIS3 500
+param set-default SIM_GZ_SV_FAIL3 500
+
+# Gas engine throttle, PCA9685 servo channel 4, "RC AUX1" (407) - left knob, or "Servo 4" (204):
+#    - on minimum when disarmed or failed:
+param set-default SIM_GZ_SV_FUNC4 204
+param set-default SIM_GZ_SV_MIN4 0
+param set-default SIM_GZ_SV_MAX4 1000
+param set-default SIM_GZ_SV_DIS4 500
+param set-default SIM_GZ_SV_FAIL4 500
+
+# Controlling PCA9685 servos 5,6,7,8 directly via "Servo 5..8" setting, by publishing actuator_servos.control[]:
+
+# Strobes, PCA9685 servo channel 5, "Servo 5" (205) - flashing indicates Mission mode:
+#param set-default SIM_GZ_SV_FUNC5 205
+#param set-default SIM_GZ_SV_MIN5 1000
+#param set-default SIM_GZ_SV_MAX5 2000
+#param set-default SIM_GZ_SV_DIS5 1000
+#param set-default SIM_GZ_SV_FAIL5 1000
+
+# Horn, PCA9685 servo channel 6, "Servo 6" (206) - for alarms like GPS failure:
+#param set-default SIM_GZ_SV_FUNC6 206
+
+# Spare PCA9685 servo channel 7 on "RC AUX2" (408) - right knob, or "Servo 7" (207):
+#param set-default SIM_GZ_SV_FUNC7 207
+
+# Spare PCA9685 servo channel 8 - "Servo 8" (208):
+#param set-default SIM_GZ_SV_FUNC8 208

ROMFS/px4fmu_common/init.d-posix/airframes/CMakeLists.txt

@@ -82,6 +82,7 @@ px4_add_romfs_files(
 	4008_gz_advanced_plane
 	4009_gz_r1_rover
 	4010_gz_x500_mono_cam
+	4011_gz_lawnmower
 
 	6011_gazebo-classic_typhoon_h480
 	6011_gazebo-classic_typhoon_h480.post

ROMFS/px4fmu_common/init.d-posix/px4-rc.simulator

@@ -41,19 +41,6 @@ elif [ "$PX4_SIMULATOR" = "gz" ] || [ "$(param show -q SIM_GZ_EN)" = "1" ]; then
 
 	echo "INFO  [init] Gazebo simulator"
 
-	# set local coordinate frame reference
-	if [ -n "${PX4_HOME_LAT}" ]; then
-		param set SIM_GZ_HOME_LAT ${PX4_HOME_LAT}
-	fi
-
-	if [ -n "${PX4_HOME_LON}" ]; then
-		param set SIM_GZ_HOME_LON ${PX4_HOME_LON}
-	fi
-
-	if [ -n "${PX4_HOME_ALT}" ]; then
-		param set SIM_GZ_HOME_ALT ${PX4_HOME_ALT}
-	fi
-
 	# Only start up Gazebo if PX4_GZ_STANDALONE is not set.
 	if [ -z "${PX4_GZ_STANDALONE}" ]; then
 
@@ -180,6 +167,12 @@ elif [ "$PX4_SIM_MODEL" = "jmavsim_iris" ] || [ "$(param show -q SYS_AUTOSTART)"
 
 else
 	# otherwise start simulator (mavlink) module
+
+	# EKF2 specifics
+	param set-default EKF2_GPS_DELAY 10
+	param set-default EKF2_MULTI_IMU 3
+	param set-default SENS_IMU_MODE 0
+
 	simulator_tcp_port=$((4560+px4_instance))
 
 	# Check if PX4_SIM_HOSTNAME environment variable is empty

ROMFS/px4fmu_common/init.d-posix/rcS

@@ -164,10 +164,6 @@ param set-default COM_RC_IN_MODE 1
 # Speedup SITL startup
 param set-default EKF2_REQ_GPS_H 0.5
 
-# Multi-EKF
-param set-default EKF2_MULTI_IMU 3
-param set-default SENS_IMU_MODE 0
-
 param set-default IMU_GYRO_FFT_EN 1
 param set-default MAV_PROTO_VER 2 # Ensures QGC does not drop the first few packets after a SITL restart due to MAVLINK 1 packets
 

ROMFS/px4fmu_common/init.d/CMakeLists.txt

@@ -34,28 +34,79 @@
 add_subdirectory(airframes)
 
 px4_add_romfs_files(
-	rc.airship_apps
-	rc.airship_defaults
+
 	rc.autostart_ext
-	rc.balloon_apps
-	rc.balloon_defaults
-	rc.boat_defaults
-	rc.fw_apps
-	rc.fw_defaults
-	rc.heli_defaults
-	rc.logging
-	rc.mc_apps
-	rc.mc_defaults
+
 	rcS
 	rc.sensors
-	rc.thermal_cal
-	rc.rover_apps
-	rc.rover_defaults
-	rc.rover_differential_apps
-	rc.rover_differential_defaults
-	rc.uuv_apps
-	rc.uuv_defaults
 	rc.vehicle_setup
-	rc.vtol_apps
-	rc.vtol_defaults
+
+	# TODO
+	rc.balloon_apps
+	rc.balloon_defaults
 )
+
+if(CONFIG_MODULES_AIRSHIP_ATT_CONTROL)
+	px4_add_romfs_files(
+		rc.airship_apps
+		rc.airship_defaults
+	)
+endif()
+
+if(CONFIG_MODULES_FW_RATE_CONTROL)
+	px4_add_romfs_files(
+		rc.fw_apps
+		rc.fw_defaults
+	)
+endif()
+
+if(CONFIG_MODULES_MC_RATE_CONTROL)
+	px4_add_romfs_files(
+		rc.heli_defaults
+		rc.mc_apps
+		rc.mc_defaults
+	)
+endif()
+
+if(CONFIG_MODULES_ROVER_POS_CONTROL)
+	px4_add_romfs_files(
+		rc.rover_apps
+		rc.rover_defaults
+
+		rc.boat_defaults # hack
+	)
+endif()
+
+if(CONFIG_MODULES_DIFFERENTIAL_DRIVE)
+	px4_add_romfs_files(
+		rc.rover_differential_apps
+		rc.rover_differential_defaults
+	)
+endif()
+
+if(CONFIG_MODULES_UUV_ATT_CONTROL)
+	px4_add_romfs_files(
+		rc.uuv_apps
+		rc.uuv_defaults
+	)
+endif()
+
+if(CONFIG_MODULES_VTOL_ATT_CONTROL)
+	px4_add_romfs_files(
+		rc.vtol_apps
+		rc.vtol_defaults
+	)
+endif()
+
+
+if(CONFIG_MODULES_LOGGER)
+	px4_add_romfs_files(
+		rc.logging
+	)
+endif()
+
+if(CONFIG_MODULES_TEMPERATURE_COMPENSATION)
+	px4_add_romfs_files(
+		rc.thermal_cal
+	)
+endif()

ROMFS/px4fmu_common/init.d/airframes/CMakeLists.txt

@@ -32,94 +32,127 @@
 ############################################################################
 
 px4_add_romfs_files(
-	# [0-999] Reserved (historical)"
-
-	# [1000, 1999] Simulation setups"
-	1001_rc_quad_x.hil
-	1002_standard_vtol.hil
-	1100_rc_quad_x_sih.hil
-	1101_rc_plane_sih.hil
-	1102_tailsitter_duo_sih.hil
-
-	# [2000, 2999] Standard planes"
-	2100_standard_plane
-	2106_albatross
-
-	2507_cloudship
-
-	# [3000, 3999] Flying wing"
-	3000_generic_wing
-
-	# [4000, 4999] Quadrotor x"
-	4001_quad_x
-	4014_s500
-	4015_holybro_s500
-	4016_holybro_px4vision
-	4017_nxp_hovergames
-	4019_x500_v2
-	4020_holybro_px4vision_v1_5
-	4041_beta75x
-	4050_generic_250
-	4052_holybro_qav250
-	4053_holybro_kopis2
-	4061_atl_mantis_edu
-	4071_ifo
-	4073_ifo-s
-	4500_clover4
-	4901_crazyflie21
-
-	# [5000, 5999] Quadrotor +"
-	5001_quad_+
-
-	# [6000, 6999] Hexarotor x"
-	6001_hexa_x
-	6002_draco_r
-
-	# [7000, 7999] Hexarotor +"
-	7001_hexa_+
-
-	# [8000, 8999] Octorotor +"
-	8001_octo_x
-
-	# [9000, 9999] Octorotor +"
-	9001_octo_+
-
-	# [11000, 11999] Hexa Cox
-	11001_hexa_cox
-
-	# [12000, 12999] Octo Cox
-	12001_octo_cox
-
-	# [13000, 13999] VTOL
-	13000_generic_vtol_standard
-	13100_generic_vtol_tiltrotor
-	13013_deltaquad
-	13014_vtol_babyshark
-	13030_generic_vtol_quad_tiltrotor
-	13200_generic_vtol_tailsitter
-
-	# [14000, 14999] MC with tilt
-	14001_generic_mc_with_tilt
-
-	16001_helicopter
-
-	# [17000, 17999] Autogyro
-	17002_TF-AutoG2
-	17003_TF-G2
+	# [0-999] Reserved (historical)
 
 	# [18000, 18999] High-altitude balloons
 	18001_TF-B1
 
 	# [22000, 22999] Reserve for custom models
-
-	24001_dodeca_cox
-
-	50000_generic_ground_vehicle
-	50004_nxpcup_car_dfrobot_gpx
-	50003_aion_robotics_r1_rover
-
-	# [60000, 61000] (Unmanned) Underwater Robots
-	60000_uuv_generic
-	60001_uuv_hippocampus
-	60002_uuv_bluerov2_heavy
 )
+
+if(CONFIG_MODULES_SIMULATION_PWM_OUT_SIM)
+	px4_add_romfs_files(
+		# [1000, 1999] Simulation setups
+		1001_rc_quad_x.hil
+		1002_standard_vtol.hil
+		1100_rc_quad_x_sih.hil
+		1101_rc_plane_sih.hil
+		1102_tailsitter_duo_sih.hil
+	)
+endif()
+
+if(CONFIG_MODULES_MC_RATE_CONTROL)
+	px4_add_romfs_files(
+		# [4000, 4999] Quadrotor x
+		4001_quad_x
+		4014_s500
+		4015_holybro_s500
+		4016_holybro_px4vision
+		4017_nxp_hovergames
+		4019_x500_v2
+		4020_holybro_px4vision_v1_5
+		4041_beta75x
+		4050_generic_250
+		4052_holybro_qav250
+		4053_holybro_kopis2
+		4061_atl_mantis_edu
+		4071_ifo
+		4073_ifo-s
+		4500_clover4
+		4901_crazyflie21
+
+		# [5000, 5999] Quadrotor +
+		5001_quad_+
+
+		# [6000, 6999] Hexarotor x
+		6001_hexa_x
+		6002_draco_r
+
+		# [7000, 7999] Hexarotor +
+		7001_hexa_+
+
+		# [8000, 8999] Octorotor +
+		8001_octo_x
+
+		# [9000, 9999] Octorotor +
+		9001_octo_+
+
+		# [11000, 11999] Hexa Cox
+		11001_hexa_cox
+
+		# [12000, 12999] Octo Cox
+		12001_octo_cox
+
+		# [14000, 14999] MC with tilt
+		14001_generic_mc_with_tilt
+
+		16001_helicopter
+
+		24001_dodeca_cox
+	)
+endif()
+
+if(CONFIG_MODULES_FW_RATE_CONTROL)
+	px4_add_romfs_files(
+		# [2000, 2999] Standard planes
+		2100_standard_plane
+		2106_albatross
+
+		# [3000, 3999] Flying wing
+		3000_generic_wing
+
+		# [17000, 17999] Autogyro
+		17002_TF-AutoG2
+		17003_TF-G2
+	)
+endif()
+
+if(CONFIG_MODULES_AIRSHIP_ATT_CONTROL)
+	px4_add_romfs_files(
+		2507_cloudship
+	)
+endif()
+
+if(CONFIG_MODULES_VTOL_ATT_CONTROL)
+	px4_add_romfs_files(
+		# [13000, 13999] VTOL
+		13000_generic_vtol_standard
+		13100_generic_vtol_tiltrotor
+		13013_deltaquad
+		13014_vtol_babyshark
+		13030_generic_vtol_quad_tiltrotor
+		13200_generic_vtol_tailsitter
+	)
+endif()
+
+if(CONFIG_MODULES_ROVER_POS_CONTROL)
+	px4_add_romfs_files(
+		50000_generic_ground_vehicle
+		50004_nxpcup_car_dfrobot_gpx
+	)
+endif()
+
+if(CONFIG_MODULES_DIFFERENTIAL_DRIVE)
+	px4_add_romfs_files(
+		50003_aion_robotics_r1_rover
+	)
+endif()
+
+if(CONFIG_MODULES_UUV_ATT_CONTROL)
+	px4_add_romfs_files(
+		# [60000, 61000] (Unmanned) Underwater Robots
+		60000_uuv_generic
+		60001_uuv_hippocampus
+		60002_uuv_bluerov2_heavy
+	)
+endif()

ROMFS/px4fmu_common/init.d/rc.fw_defaults

@@ -28,7 +28,6 @@ param set-default EKF2_ARSP_THR 8
 param set-default EKF2_FUSE_BETA 1
 param set-default EKF2_GPS_CHECK 21
 param set-default EKF2_MAG_ACCLIM 0
-param set-default EKF2_MAG_YAWLIM 0
 param set-default EKF2_REQ_EPH 10
 param set-default EKF2_REQ_EPV 10
 param set-default EKF2_REQ_HDRIFT 0.5

ROMFS/px4fmu_common/init.d/rc.rover_differential_apps

@@ -5,7 +5,7 @@
 ekf2 start &
 
 # Start rover differential drive controller.
-differential_drive_control start
+differential_drive start
 
 # Start Land Detector.
 land_detector start rover

ROMFS/px4fmu_common/init.d/rcS

@@ -439,7 +439,12 @@ else
 	#
 	# Start a thermal calibration if required.
 	#
-	. ${R}etc/init.d/rc.thermal_cal
+	set RC_THERMAL_CAL ${R}etc/init.d/rc.thermal_cal
+	if [ -f ${RC_THERMAL_CAL} ]
+	then
+		. ${RC_THERMAL_CAL}
+	fi
+	unset RC_THERMAL_CAL
 
 	#
 	# Start gimbal to control mounts such as gimbals, disabled by default.
@@ -500,7 +505,12 @@ else
 	#
 	# Start the logger.
 	#
-	. ${R}etc/init.d/rc.logging
+	set RC_LOGGING ${R}etc/init.d/rc.logging
+	if [ -f ${RC_LOGGING} ]
+	then
+		. ${RC_LOGGING}
+	fi
+	unset RC_LOGGING
 
 	#
 	# Set additional parameters and env variables for selected AUTOSTART.

Tools/astyle/files_to_check_code_style.sh

@@ -30,4 +30,5 @@ exec find boards msg src platforms test \
     -path src/lib/cdrstream/cyclonedds -prune -o \
     -path src/lib/cdrstream/rosidl -prune -o \
     -path src/modules/zenoh/zenoh-pico -prune -o \
+    -path src/modules/muorb/apps/libfc-sensor-api -prune -o \
     -type f \( -name "*.c" -o -name "*.h" -o -name "*.cpp" -o -name "*.hpp" \) | grep $PATTERN

Tools/msg/templates/uorb/msg.cpp.em

@@ -73,9 +73,16 @@ struct_size, padding_end_size = add_padding_bytes(sorted_fields, search_path)
 #include <lib/matrix/matrix/math.hpp>
 #include <lib/mathlib/mathlib.h>
 
+@{
+queue_length = 1
+for constant in spec.constants:
+	if constant.name == 'ORB_QUEUE_LENGTH':
+		queue_length = constant.val
+}@
+
 @[for topic in topics]@
 static_assert(static_cast<orb_id_size_t>(ORB_ID::@topic) == @(all_topics.index(topic)), "ORB_ID index mismatch");
-ORB_DEFINE(@topic, struct @uorb_struct, @(struct_size-padding_end_size), @(message_hash)u, static_cast<orb_id_size_t>(ORB_ID::@topic));
+ORB_DEFINE(@topic, struct @uorb_struct, @(struct_size-padding_end_size), @(message_hash)u, static_cast<orb_id_size_t>(ORB_ID::@topic), @queue_length);
 @[end for]
 
 void print_message(const orb_metadata *meta, const @uorb_struct& message)

boards/ark/septentrio-gps/canbootloader.px4board

@@ -0,0 +1,5 @@
+CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
+CONFIG_BOARD_ARCHITECTURE="cortex-m4"
+CONFIG_BOARD_ROMFSROOT=""
+CONFIG_BOARD_CONSTRAINED_MEMORY=y
+CONFIG_DRIVERS_BOOTLOADERS=y

boards/ark/septentrio-gps/default.px4board

@@ -0,0 +1,37 @@
+CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
+CONFIG_BOARD_ARCHITECTURE="cortex-m4"
+CONFIG_BOARD_ROMFSROOT="cannode"
+CONFIG_BOARD_NO_HELP=y
+CONFIG_BOARD_CONSTRAINED_MEMORY=y
+CONFIG_DRIVERS_BAROMETER_BMP388=y
+CONFIG_DRIVERS_BOOTLOADERS=y
+CONFIG_DRIVERS_GPS=y
+CONFIG_DRIVERS_IMU_INVENSENSE_ICM42688P=y
+CONFIG_DRIVERS_MAGNETOMETER_BOSCH_BMM150=y
+CONFIG_DRIVERS_SAFETY_BUTTON=y
+CONFIG_DRIVERS_TONE_ALARM=y
+CONFIG_BOARD_UAVCAN_INTERFACES=1
+CONFIG_DRIVERS_UAVCANNODE=y
+CONFIG_UAVCANNODE_BEEP_COMMAND=y
+CONFIG_UAVCANNODE_GNSS_FIX=y
+CONFIG_UAVCANNODE_LIGHTS_COMMAND=y
+CONFIG_UAVCANNODE_MAGNETIC_FIELD_STRENGTH=y
+CONFIG_UAVCANNODE_RTK_DATA=y
+CONFIG_UAVCANNODE_SAFETY_BUTTON=y
+CONFIG_UAVCANNODE_STATIC_PRESSURE=y
+CONFIG_UAVCANNODE_STATIC_TEMPERATURE=y
+CONFIG_MODULES_GYRO_CALIBRATION=y
+CONFIG_MODULES_MAG_BIAS_ESTIMATOR=y
+CONFIG_MODULES_SENSORS=y
+# CONFIG_SENSORS_VEHICLE_AIRSPEED is not set
+# CONFIG_SENSORS_VEHICLE_AIR_DATA is not set
+# CONFIG_SENSORS_VEHICLE_GPS_POSITION is not set
+CONFIG_SYSTEMCMDS_PARAM=y
+CONFIG_SYSTEMCMDS_PERF=y
+CONFIG_SYSTEMCMDS_REBOOT=y
+CONFIG_SYSTEMCMDS_SYSTEM_TIME=y
+CONFIG_SYSTEMCMDS_TOP=y
+CONFIG_SYSTEMCMDS_TOPIC_LISTENER=y
+CONFIG_SYSTEMCMDS_UORB=y
+CONFIG_SYSTEMCMDS_VER=y
+CONFIG_SYSTEMCMDS_WORK_QUEUE=y

boards/ark/septentrio-gps/firmware.prototype

@@ -0,0 +1,13 @@
+{
+    "board_id": 84,
+    "magic": "PX4FWv1",
+    "description": "Firmware for the ARK Septentrio GPS board",
+    "image": "",
+    "build_time": 0,
+    "summary": "ARKSEPTENTRIOGPS",
+    "version": "0.1",
+    "image_size": 0,
+    "image_maxsize": 2080768,
+    "git_identity": "",
+    "board_revision": 0
+}

boards/ark/septentrio-gps/init/rc.board_defaults

@@ -0,0 +1,13 @@
+#!/bin/sh
+#
+# board specific defaults
+#------------------------------------------------------------------------------
+
+param set-default CBRK_IO_SAFETY 0
+param set-default CANNODE_SUB_MBD 1
+param set-default CANNODE_SUB_RTCM 1
+param set-default MBE_ENABLE 1
+param set-default SENS_IMU_CLPNOTI 0
+
+safety_button start
+tone_alarm start

boards/ark/septentrio-gps/init/rc.board_sensors

@@ -0,0 +1,11 @@
+#!/bin/sh
+#
+# board sensors init
+#------------------------------------------------------------------------------
+gps start -d /dev/ttyS0 -p sbf
+
+icm42688p -R 0 -s start
+
+bmp388 -I -b 1 start
+
+bmm150 -I -b 1 start

boards/ark/septentrio-gps/nuttx-config/canbootloader/defconfig

@@ -0,0 +1,56 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+CONFIG_ARCH="arm"
+CONFIG_ARCH_BOARD_CUSTOM=y
+CONFIG_ARCH_BOARD_CUSTOM_DIR="../../../../boards/ark/septentrio-gps/nuttx-config"
+CONFIG_ARCH_BOARD_CUSTOM_DIR_RELPATH=y
+CONFIG_ARCH_BOARD_CUSTOM_NAME="px4"
+CONFIG_ARCH_CHIP="stm32"
+CONFIG_ARCH_CHIP_STM32=y
+CONFIG_ARCH_CHIP_STM32F412CE=y
+CONFIG_ARCH_INTERRUPTSTACK=4096
+CONFIG_ARMV7M_MEMCPY=y
+CONFIG_ARMV7M_USEBASEPRI=y
+CONFIG_BINFMT_DISABLE=y
+CONFIG_BOARDCTL=y
+CONFIG_BOARD_LOOPSPERMSEC=16717
+CONFIG_DEBUG_FULLOPT=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_DEBUG_TCBINFO=y
+CONFIG_DEFAULT_SMALL=y
+CONFIG_DISABLE_MOUNTPOINT=y
+CONFIG_EXPERIMENTAL=y
+CONFIG_FDCLONE_DISABLE=y
+CONFIG_FDCLONE_STDIO=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_IDLETHREAD_STACKSIZE=4096
+CONFIG_INIT_STACKSIZE=4096
+CONFIG_LIBC_FLOATINGPOINT=y
+CONFIG_LIBC_LONG_LONG=y
+CONFIG_LIBC_STRERROR=y
+CONFIG_MM_REGIONS=2
+CONFIG_NAME_MAX=0
+CONFIG_NUNGET_CHARS=0
+CONFIG_PREALLOC_TIMERS=0
+CONFIG_PTHREAD_STACK_MIN=512
+CONFIG_RAM_SIZE=262144
+CONFIG_RAM_START=0x20010000
+CONFIG_RAW_BINARY=y
+CONFIG_SIG_DEFAULT=y
+CONFIG_SIG_SIGALRM_ACTION=y
+CONFIG_SIG_SIGUSR1_ACTION=y
+CONFIG_SIG_SIGUSR2_ACTION=y
+CONFIG_STACK_COLORATION=y
+CONFIG_START_DAY=30
+CONFIG_START_MONTH=11
+CONFIG_STDIO_DISABLE_BUFFERING=y
+CONFIG_STM32_NOEXT_VECTORS=y
+CONFIG_STM32_TIM8=y
+CONFIG_TASK_NAME_SIZE=0
+CONFIG_USEC_PER_TICK=1000

boards/ark/septentrio-gps/nuttx-config/include/board.h

@@ -0,0 +1,152 @@
+/************************************************************************************
+ * configs/px4fmu/include/board.h
+ * include/arch/board/board.h
+ *
+ *   Copyright (C) 2009 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ************************************************************************************/
+#include "board_dma_map.h"
+
+#ifndef __ARCH_BOARD_BOARD_H
+#define __ARCH_BOARD_BOARD_H
+
+#include <nuttx/config.h>
+#ifndef __ASSEMBLY__
+# include <stdint.h>
+#endif
+
+#include <stm32.h>
+
+/* HSI - 8 MHz RC factory-trimmed
+ * LSI - 32 KHz RC
+ * HSE - 8  MHz Crystal
+ * LSE - not installed
+ */
+#define STM32_BOARD_USEHSE      1
+#define STM32_BOARD_XTAL        8000000
+#define STM32_HSE_FREQUENCY     STM32_BOARD_XTAL
+
+#define STM32_HSI_FREQUENCY     16000000ul
+#define STM32_LSI_FREQUENCY     32000
+
+/* Main PLL Configuration */
+#define STM32_PLLCFG_PLLM       RCC_PLLCFG_PLLM(8)
+#define STM32_PLLCFG_PLLN       RCC_PLLCFG_PLLN(384)
+#define STM32_PLLCFG_PLLP       RCC_PLLCFG_PLLP_4
+#define STM32_PLLCFG_PLLQ       RCC_PLLCFG_PLLQ(8)
+#define STM32_PLLCFG_PLLR       RCC_PLLCFG_PLLR(2)
+
+#define STM32_RCC_PLLI2SCFGR_PLLI2SM RCC_PLLI2SCFGR_PLLI2SM(16)
+#define STM32_RCC_PLLI2SCFGR_PLLI2SN RCC_PLLI2SCFGR_PLLI2SN(192)
+#define STM32_RCC_PLLI2SCFGR_PLLI2SQ RCC_PLLI2SCFGR_PLLI2SQ(2)
+#define STM32_RCC_PLLI2SCFGR_PLLI2SR RCC_PLLI2SCFGR_PLLI2SR(2)
+#define STM32_RCC_PLLI2SCFGR_PLLI2SSRC RCC_PLLI2SCFGR_PLLI2SSRC(0) /* HSE or HSI depending on PLLSRC of PLLCFGR*/
+
+#define STM32_RCC_DCKCFGR2_CK48MSEL RCC_DCKCFGR2_CK48MSEL_PLL
+#define STM32_RCC_DCKCFGR2_FMPI2C1SEL RCC_DCKCFGR2_FMPI2C1SEL_APB
+#define STM32_RCC_DCKCFGR2_SDIOSEL RCC_DCKCFGR2_SDIOSEL_48MHZ
+
+#define STM32_SYSCLK_FREQUENCY  96000000ul
+
+/* AHB clock (HCLK) is SYSCLK (96MHz) */
+#define STM32_RCC_CFGR_HPRE     RCC_CFGR_HPRE_SYSCLK      /* HCLK  = SYSCLK / 1 */
+#define STM32_HCLK_FREQUENCY    STM32_SYSCLK_FREQUENCY
+#define STM32_BOARD_HCLK        STM32_HCLK_FREQUENCY      /* Same as above, to satisfy compiler */
+
+/* APB1 clock (PCLK1) is HCLK/2 (48MHz) */
+#define STM32_RCC_CFGR_PPRE1    RCC_CFGR_PPRE1_HCLKd2     /* PCLK1 = HCLK / 2 */
+#define STM32_PCLK1_FREQUENCY   (STM32_HCLK_FREQUENCY/2)
+
+/* Timers driven from APB1 will be twice PCLK1 (see page 112 of reference manual) */
+#define STM32_APB1_TIM2_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM3_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM4_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM5_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM12_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM13_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM14_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+
+/* APB2 clock (PCLK2) is HCLK (96MHz) */
+#define STM32_RCC_CFGR_PPRE2    RCC_CFGR_PPRE2_HCLK       /* PCLK2 = HCLK */
+#define STM32_PCLK2_FREQUENCY   (STM32_HCLK_FREQUENCY)
+
+/* Timers driven from APB2 will be PCLK2 since no prescale division */
+#define STM32_APB2_TIM1_CLKIN   (STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM8_CLKIN   (STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM9_CLKIN   (STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM10_CLKIN  (STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM11_CLKIN  (STM32_PCLK2_FREQUENCY)
+
+/* Timer Frequencies, if APBx is set to 1, frequency is same to APBx otherwise frequency is 2xAPBx. */
+#define BOARD_TIM2_FREQUENCY    (2 * STM32_PCLK1_FREQUENCY)
+#define BOARD_TIM3_FREQUENCY    (2 * STM32_PCLK1_FREQUENCY)
+#define BOARD_TIM4_FREQUENCY    (2 * STM32_PCLK1_FREQUENCY)
+#define BOARD_TIM5_FREQUENCY    (2 * STM32_PCLK1_FREQUENCY)
+#define BOARD_TIM6_FREQUENCY    (2 * STM32_PCLK1_FREQUENCY)
+#define BOARD_TIM7_FREQUENCY    (2 * STM32_PCLK1_FREQUENCY)
+#define BOARD_TIM8_FREQUENCY    (2 * STM32_PCLK2_FREQUENCY)
+
+/* Alternate function pin selections ************************************************/
+
+/* UARTs */
+#define GPIO_USART1_RX	GPIO_USART1_RX_2
+#define GPIO_USART1_TX	GPIO_USART1_TX_3
+
+#define GPIO_USART2_RX	GPIO_USART2_RX_1
+#define GPIO_USART2_TX	GPIO_USART2_TX_1
+
+/* CAN */
+#define GPIO_CAN1_RX	GPIO_CAN1_RX_1
+#define GPIO_CAN1_TX	GPIO_CAN1_TX_1
+
+/* I2C */
+
+#define GPIO_MCU_I2C1_SCL
+#define GPIO_MCU_I2C1_SDA
+
+#define GPIO_I2C1_SCL	GPIO_I2C1_SCL_1
+#define GPIO_I2C1_SDA	GPIO_I2C1_SDA_1
+
+#define GPIO_I2C1_SCL_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN6)
+#define GPIO_I2C1_SDA_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN7)
+
+#define GPIO_I2C2_SCL	GPIO_I2C2_SCL_1
+#define GPIO_I2C2_SDA	GPIO_I2C2_SDA_4
+
+#define GPIO_I2C2_SCL_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN9)
+#define GPIO_I2C2_SDA_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN10)
+
+/* SPI */
+#define GPIO_SPI1_MISO  GPIO_SPI1_MISO_1
+#define GPIO_SPI1_MOSI  GPIO_SPI1_MOSI_1
+#define GPIO_SPI1_SCK   GPIO_SPI1_SCK_1
+
+#endif /* __ARCH_BOARD_BOARD_H */

boards/ark/septentrio-gps/nuttx-config/include/board_dma_map.h

@@ -0,0 +1,46 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#pragma once
+
+// DMA1 Channel/Stream Selections
+//--------------------------------------------//---------------------------//----------------
+
+
+//  DMA2 Channel/Stream Selections
+//--------------------------------------------//---------------------------//----------------
+#define DMACHAN_SPI1_RX    DMAMAP_SPI1_RX_1   // DMA2, Stream 0, Channel 3
+#define DMACHAN_SPI1_TX    DMAMAP_SPI1_TX_1   // DMA2, Stream 3, Channel 3
+#define DMACHAN_USART1_RX  DMAMAP_USART1_RX_1 // DMA2, Stream 2, Channel 4
+#define DMAMAP_USART1_RX   DMAMAP_USART1_RX_1
+//#define DMACHAN_USART1_TX  DMAMAP_USART1_TX   // DMA2, Stream 7, Channel 4

boards/ark/septentrio-gps/nuttx-config/nsh/defconfig

@@ -0,0 +1,152 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_DISABLE_ENVIRON is not set
+# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set
+# CONFIG_DISABLE_PTHREAD is not set
+# CONFIG_NSH_DISABLEBG is not set
+# CONFIG_NSH_DISABLESCRIPT is not set
+# CONFIG_NSH_DISABLE_CAT is not set
+# CONFIG_NSH_DISABLE_CD is not set
+# CONFIG_NSH_DISABLE_CP is not set
+# CONFIG_NSH_DISABLE_DATE is not set
+# CONFIG_NSH_DISABLE_DF is not set
+# CONFIG_NSH_DISABLE_ECHO is not set
+# CONFIG_NSH_DISABLE_ENV is not set
+# CONFIG_NSH_DISABLE_EXEC is not set
+# CONFIG_NSH_DISABLE_EXPORT is not set
+# CONFIG_NSH_DISABLE_FREE is not set
+# CONFIG_NSH_DISABLE_GET is not set
+# CONFIG_NSH_DISABLE_HELP is not set
+# CONFIG_NSH_DISABLE_ITEF is not set
+# CONFIG_NSH_DISABLE_KILL is not set
+# CONFIG_NSH_DISABLE_LOOPS is not set
+# CONFIG_NSH_DISABLE_LS is not set
+# CONFIG_NSH_DISABLE_MKDIR is not set
+# CONFIG_NSH_DISABLE_MOUNT is not set
+# CONFIG_NSH_DISABLE_MV is not set
+# CONFIG_NSH_DISABLE_PS is not set
+# CONFIG_NSH_DISABLE_PSSTACKUSAGE is not set
+# CONFIG_NSH_DISABLE_PWD is not set
+# CONFIG_NSH_DISABLE_RM is not set
+# CONFIG_NSH_DISABLE_RMDIR is not set
+# CONFIG_NSH_DISABLE_SEMICOLON is not set
+# CONFIG_NSH_DISABLE_SET is not set
+# CONFIG_NSH_DISABLE_SLEEP is not set
+# CONFIG_NSH_DISABLE_SOURCE is not set
+# CONFIG_NSH_DISABLE_TEST is not set
+# CONFIG_NSH_DISABLE_TIME is not set
+# CONFIG_NSH_DISABLE_UMOUNT is not set
+# CONFIG_NSH_DISABLE_UNSET is not set
+# CONFIG_NSH_DISABLE_USLEEP is not set
+CONFIG_ARCH="arm"
+CONFIG_ARCH_BOARD_CUSTOM=y
+CONFIG_ARCH_BOARD_CUSTOM_DIR="../../../../boards/ark/septentrio-gps/nuttx-config"
+CONFIG_ARCH_BOARD_CUSTOM_DIR_RELPATH=y
+CONFIG_ARCH_BOARD_CUSTOM_NAME="px4"
+CONFIG_ARCH_CHIP="stm32"
+CONFIG_ARCH_CHIP_STM32=y
+CONFIG_ARCH_CHIP_STM32F412CE=y
+CONFIG_ARCH_INTERRUPTSTACK=768
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARMV7M_MEMCPY=y
+CONFIG_ARMV7M_USEBASEPRI=y
+CONFIG_BOARDCTL_RESET=y
+CONFIG_BOARD_ASSERT_RESET_VALUE=0
+CONFIG_BOARD_LOOPSPERMSEC=16717
+CONFIG_BOARD_RESET_ON_ASSERT=2
+CONFIG_BUILTIN=y
+CONFIG_DEBUG_FULLOPT=y
+CONFIG_DEBUG_HARDFAULT_ALERT=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_DEBUG_TCBINFO=y
+CONFIG_DEFAULT_SMALL=y
+CONFIG_FDCLONE_STDIO=y
+CONFIG_FS_CROMFS=y
+CONFIG_FS_ROMFS=y
+CONFIG_GRAN=y
+CONFIG_GRAN_INTR=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_I2C=y
+CONFIG_I2C_RESET=y
+CONFIG_IDLETHREAD_STACKSIZE=750
+CONFIG_INIT_ENTRYPOINT="nsh_main"
+CONFIG_INIT_STACKSIZE=2624
+CONFIG_LIBC_FLOATINGPOINT=y
+CONFIG_LIBC_LONG_LONG=y
+CONFIG_LIBC_MAX_EXITFUNS=1
+CONFIG_MEMSET_64BIT=y
+CONFIG_MEMSET_OPTSPEED=y
+CONFIG_MM_REGIONS=2
+CONFIG_NAME_MAX=40
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_ARGCAT=y
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_CMDPARMS=y
+CONFIG_NSH_CROMFSETC=y
+CONFIG_NSH_LINELEN=128
+CONFIG_NSH_MAXARGUMENTS=15
+CONFIG_NSH_NESTDEPTH=8
+CONFIG_NSH_QUOTE=y
+CONFIG_NSH_ROMFSETC=y
+CONFIG_NSH_ROMFSSECTSIZE=128
+CONFIG_NSH_VARS=y
+CONFIG_PREALLOC_TIMERS=50
+CONFIG_PTHREAD_MUTEX_ROBUST=y
+CONFIG_PTHREAD_STACK_MIN=512
+CONFIG_RAM_SIZE=262144
+CONFIG_RAM_START=0x20000000
+CONFIG_RAW_BINARY=y
+CONFIG_SCHED_HPWORK=y
+CONFIG_SCHED_HPWORKPRIORITY=249
+CONFIG_SCHED_HPWORKSTACKSIZE=1280
+CONFIG_SCHED_INSTRUMENTATION=y
+CONFIG_SCHED_INSTRUMENTATION_EXTERNAL=y
+CONFIG_SCHED_INSTRUMENTATION_SWITCH=y
+CONFIG_SCHED_WAITPID=y
+CONFIG_SERIAL_TERMIOS=y
+CONFIG_SIG_DEFAULT=y
+CONFIG_SIG_SIGALRM_ACTION=y
+CONFIG_SIG_SIGUSR1_ACTION=y
+CONFIG_SIG_SIGUSR2_ACTION=y
+CONFIG_SIG_SIGWORK=4
+CONFIG_STACK_COLORATION=y
+CONFIG_START_DAY=30
+CONFIG_START_MONTH=11
+CONFIG_STDIO_BUFFER_SIZE=32
+CONFIG_STM32_ADC1=y
+CONFIG_STM32_DISABLE_IDLE_SLEEP_DURING_DEBUG=y
+CONFIG_STM32_DMA1=y
+CONFIG_STM32_DMA2=y
+CONFIG_STM32_FLASH_PREFETCH=y
+CONFIG_STM32_FLOWCONTROL_BROKEN=y
+CONFIG_STM32_I2C1=y
+CONFIG_STM32_I2C2=y
+CONFIG_STM32_JTAG_SW_ENABLE=y
+CONFIG_STM32_PWR=y
+CONFIG_STM32_SERIALBRK_BSDCOMPAT=y
+CONFIG_STM32_SERIAL_DISABLE_REORDERING=y
+CONFIG_STM32_SPI1=y
+CONFIG_STM32_SPI1_DMA=y
+CONFIG_STM32_SPI1_DMA_BUFFER=1024
+CONFIG_STM32_TIM8=y
+CONFIG_STM32_USART1=y
+CONFIG_STM32_USART2=y
+CONFIG_STM32_USART_BREAKS=y
+CONFIG_STM32_WWDG=y
+CONFIG_SYSTEM_NSH=y
+CONFIG_TASK_NAME_SIZE=24
+CONFIG_USART1_BAUD=57600
+CONFIG_USART1_RXBUFSIZE=2000
+CONFIG_USART1_RXDMA=y
+CONFIG_USART1_TXBUFSIZE=2000
+CONFIG_USART2_BAUD=57600
+CONFIG_USART2_RXBUFSIZE=600
+CONFIG_USART2_SERIAL_CONSOLE=y
+CONFIG_USART2_TXBUFSIZE=1100
+CONFIG_USEC_PER_TICK=1000

boards/ark/septentrio-gps/nuttx-config/scripts/canbootloader_script.ld

@@ -0,0 +1,134 @@
+/****************************************************************************
+ * nuttx-config/scripts/canbootloader_script.ld
+ *
+ *   Copyright (C) 2015 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F412 has 512Kb of FLASH beginning at address 0x0800:0000 and
+ * 256Kb of SRAM. SRAM is split up into three blocks:
+ *
+ * 1) 112Kb of SRAM beginning at address 0x2000:0000
+ * 2)  16Kb of SRAM beginning at address 0x2001:c000
+ * 3)  64Kb of SRAM beginning at address 0x2002:0000
+ * 4)  64Kb of TCM SRAM beginning at address 0x1000:0000
+ *
+ * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
+ * where the code expects to begin execution by jumping to the entry point in
+ * the 0x0800:0000 address range.
+ *
+ * The first 0x10000 of flash is reserved for the bootloader.
+ */
+
+MEMORY
+{
+    flash (rx)   : ORIGIN = 0x08000000, LENGTH = 32K
+    sram (rwx)   : ORIGIN = 0x20000000, LENGTH = 192K
+}
+
+OUTPUT_ARCH(arm)
+
+ENTRY(__start)		/* treat __start as the anchor for dead code stripping */
+EXTERN(_vectors)	/* force the vectors to be included in the output */
+
+/*
+ * Ensure that abort() is present in the final object.  The exception handling
+ * code pulled in by libgcc.a requires it (and that code cannot be easily avoided).
+ */
+EXTERN(abort)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)
+		*(.gnu.linkonce.t.*)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	/*
+	 * Init functions (static constructors and the like)
+	 */
+        .init_section : {
+                _sinit = ABSOLUTE(.);
+                KEEP(*(.init_array .init_array.*))
+                _einit = ABSOLUTE(.);
+        } > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} > flash
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} > flash
+	__exidx_end = ABSOLUTE(.);
+
+	_eronly = ABSOLUTE(.);
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		. = ALIGN(4);
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}

boards/ark/septentrio-gps/nuttx-config/scripts/script.ld

@@ -0,0 +1,146 @@
+/****************************************************************************
+ * scripts/ld.script
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F412 has 512Kb of FLASH beginning at address 0x0800:0000 and
+ * 256Kb of SRAM. SRAM is split up into three blocks:
+ *
+ * 1) 112Kb of SRAM beginning at address 0x2000:0000
+ * 2)  16Kb of SRAM beginning at address 0x2001:c000
+ * 3)  64Kb of SRAM beginning at address 0x2002:0000
+ * 4)  64Kb of TCM SRAM beginning at address 0x1000:0000
+ *
+ * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
+ * where the code expects to begin execution by jumping to the entry point in
+ * the 0x0800:0000 address range.
+ *
+ * The first 0x10000 of flash is reserved for the bootloader.
+ */
+
+MEMORY
+{
+    flash (rx)   : ORIGIN = 0x08010000, LENGTH = 928K
+    sram (rwx)   : ORIGIN = 0x20000000, LENGTH = 192K
+}
+
+OUTPUT_ARCH(arm)
+
+ENTRY(__start)		/* treat __start as the anchor for dead code stripping */
+EXTERN(_vectors)	/* force the vectors to be included in the output */
+
+/*
+ * Ensure that abort() is present in the final object.  The exception handling
+ * code pulled in by libgcc.a requires it (and that code cannot be easily avoided).
+ */
+EXTERN(abort)
+EXTERN(_bootdelay_signature)
+
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		. = ALIGN(8);
+		/*
+		* This section positions the app_descriptor_t used
+		* by the make_can_boot_descriptor.py tool to set
+		* the application image's descriptor so that the
+		* uavcan bootloader has the ability to validate the
+		* image crc, size etc
+		*/
+		KEEP(*(.app_descriptor))
+		*(.text .text.*)
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)
+		*(.gnu.linkonce.t.*)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	/*
+	 * Init functions (static constructors and the like)
+	 */
+        .init_section : {
+                _sinit = ABSOLUTE(.);
+                KEEP(*(.init_array .init_array.*))
+                _einit = ABSOLUTE(.);
+        } > flash
+
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} > flash
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} > flash
+	__exidx_end = ABSOLUTE(.);
+
+	_eronly = ABSOLUTE(.);
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		. = ALIGN(4);
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}

boards/ark/septentrio-gps/src/CMakeLists.txt

@@ -0,0 +1,67 @@
+############################################################################
+#
+#   Copyright (c) 2020 PX4 Development Team. All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name PX4 nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+if("${PX4_BOARD_LABEL}" STREQUAL  "canbootloader")
+
+	add_library(drivers_board
+		boot_config.h
+		boot.c
+		led.c
+		led.h
+	)
+	target_link_libraries(drivers_board
+		PRIVATE
+			nuttx_arch
+			nuttx_drivers
+			canbootloader
+	)
+	target_include_directories(drivers_board PRIVATE ${PX4_SOURCE_DIR}/platforms/nuttx/src/canbootloader)
+
+else()
+	add_library(drivers_board
+		can.c
+		i2c.cpp
+		init.c
+		led.c
+		spi.cpp
+	)
+
+	target_link_libraries(drivers_board
+		PRIVATE
+			arch_spi
+			drivers__led # drv_led_start
+			nuttx_arch
+			nuttx_drivers
+			px4_layer
+	)
+endif()

boards/ark/septentrio-gps/src/board_config.h

@@ -0,0 +1,125 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file board_config.h
+ *
+ * board internal definitions
+ */
+
+#pragma once
+
+#include <px4_platform_common/px4_config.h>
+#include <nuttx/compiler.h>
+#include <stdint.h>
+
+/* BUTTON */
+#define GPIO_BTN_SAFETY       /* PB15 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTB|GPIO_PIN15)
+
+/* Safety LED */
+#define GPIO_LED_SAFETY       /* PA1  */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN1)
+
+/* Tone alarm output. */
+#define TONE_ALARM_TIMER             2    /* timer 2 */
+#define TONE_ALARM_CHANNEL           1    /* channel 1 */
+#define GPIO_TONE_ALARM_IDLE  /* PA0  */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN0)
+#define GPIO_TONE_ALARM       /* PA0  */ (GPIO_ALT|GPIO_AF1|GPIO_SPEED_2MHz|GPIO_PUSHPULL|GPIO_PORTA|GPIO_PIN0)
+
+/* CAN  Silent mode control */
+#define GPIO_CAN1_SILENT_S0   /* PB12 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN12)
+
+/* CAN termination software control */
+#define GPIO_CAN1_TERMINATION /* PB13 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN13)
+#define GPIO_CAN_TERM                    GPIO_CAN1_TERMINATION
+
+/* ICM42688p FSYNC */
+#define GPIO_42688P_FSYNC     /* PB8  */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN8)
+
+/* Boot config */
+#define GPIO_BOOT_CONFIG      /* PC15 */ (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTC|GPIO_PIN15|GPIO_EXTI)
+
+/* LEDs are driven with open drain to support Anode to 5V or 3.3V */
+#define GPIO_TIM1_CH1         /* PA8  */ (GPIO_TIM1_CH1_1|GPIO_OPENDRAIN|GPIO_SPEED_2MHz)
+#define GPIO_TIM1_CH2         /* PA9  */ (GPIO_TIM1_CH2_1|GPIO_OPENDRAIN|GPIO_SPEED_2MHz)
+#define GPIO_TIM1_CH3         /* PA10 */ (GPIO_TIM1_CH3_1|GPIO_OPENDRAIN|GPIO_SPEED_2MHz)
+
+#define GPIO_I2C1_SCL_RESET   /* PB6  */  (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN6)
+#define GPIO_I2C1_SDA_RESET   /* PB7  */  (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN7)
+
+#define GPIO_I2C2_SCL_RESET   /* PB10 */  (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN10)
+#define GPIO_I2C2_SDA_RESET   /* PB9  */  (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN9)
+
+#define GPIO_I2C2_SCL_RESET   /* PB10 */  (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN10)
+#define GPIO_I2C2_SDA_RESET   /* PB9  */  (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN9)
+
+#define GPIO_USART1_RX_GPIO	(GPIO_INPUT|GPIO_PULLUP|GPIO_SPEED_50MHz|GPIO_PORTB|GPIO_PIN3)
+#define GPIO_USART1_TX_GPIO	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_PULLUP|GPIO_SPEED_50MHz|GPIO_PORTA|GPIO_PIN15)
+
+#define GPIO_USART2_RX_GPIO	(GPIO_INPUT|GPIO_PULLUP|GPIO_SPEED_50MHz|GPIO_PORTA|GPIO_PIN3)
+#define GPIO_USART2_TX_GPIO	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_PULLUP|GPIO_SPEED_50MHz|GPIO_PORTA|GPIO_PIN2)
+
+#define FLASH_BASED_PARAMS
+
+/* High-resolution timer */
+#define HRT_TIMER                    3  /* use timer 3 for the HRT */
+#define HRT_TIMER_CHANNEL            4  /* use capture/compare channel 4 */
+
+#define PX4_GPIO_INIT_LIST { \
+		GPIO_BTN_SAFETY,                  \
+		GPIO_LED_SAFETY,                  \
+		GPIO_I2C1_SCL_RESET,              \
+		GPIO_I2C1_SDA_RESET,              \
+		GPIO_I2C2_SCL_RESET,              \
+		GPIO_I2C2_SDA_RESET,              \
+		GPIO_42688P_FSYNC,                \
+		GPIO_BOOT_CONFIG,                 \
+		GPIO_CAN1_TX,                     \
+		GPIO_CAN1_RX,                     \
+		GPIO_CAN1_SILENT_S0,              \
+		GPIO_CAN1_TERMINATION,            \
+	}
+
+__BEGIN_DECLS
+
+#define BOARD_HAS_N_S_RGB_LED       1
+#define BOARD_MAX_LEDS              BOARD_HAS_N_S_RGB_LED
+
+#ifndef __ASSEMBLY__
+
+extern void stm32_spiinitialize(void);
+
+#include <px4_platform_common/board_common.h>
+
+#endif /* __ASSEMBLY__ */
+
+__END_DECLS

boards/ark/septentrio-gps/src/boot.c

@@ -0,0 +1,188 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2021 PX4 Development Team. All rights reserved.
+ *       Author: Ben Dyer <ben_dyer@mac.com>
+ *               Pavel Kirienko <pavel.kirienko@zubax.com>
+ *               David Sidrane <david_s5@nscdg.com>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <px4_config.h>
+#include <stdint.h>
+#include "boot_config.h"
+#include "board.h"
+
+#include <debug.h>
+#include <string.h>
+#include <arch/board/board.h>
+
+#include <nuttx/board.h>
+#include "led.h"
+
+/************************************************************************************
+ * Name: stm32_boardinitialize
+ *
+ * Description:
+ *   All STM32 architectures must provide the following entry point.  This entry point
+ *   is called early in the initialization -- after all memory has been configured
+ *   and mapped but before any devices have been initialized.
+ *
+ ************************************************************************************/
+
+__EXPORT void stm32_boardinitialize(void)
+{
+	putreg32(getreg32(STM32_RCC_APB1ENR) | RCC_APB1ENR_CAN1EN, STM32_RCC_APB1ENR);
+	stm32_configgpio(GPIO_CAN1_RX);
+	stm32_configgpio(GPIO_CAN1_TX);
+	stm32_configgpio(GPIO_CAN1_SILENT_S0);
+	stm32_configgpio(GPIO_CAN1_TERMINATION);
+	putreg32(getreg32(STM32_RCC_APB1RSTR) | RCC_APB1RSTR_CAN1RST, STM32_RCC_APB1RSTR);
+	putreg32(getreg32(STM32_RCC_APB1RSTR) & ~RCC_APB1RSTR_CAN1RST, STM32_RCC_APB1RSTR);
+
+#if defined(OPT_WAIT_FOR_GETNODEINFO_JUMPER_GPIO)
+	stm32_configgpio(GPIO_GETNODEINFO_JUMPER);
+#endif
+
+}
+
+/************************************************************************************
+ * Name: board_deinitialize
+ *
+ * Description:
+ *   This function is called by the bootloader code prior to booting
+ *   the application. Is should place the HW into an benign initialized state.
+ *
+ ************************************************************************************/
+
+void board_deinitialize(void)
+{
+	putreg32(getreg32(STM32_RCC_APB1RSTR) | RCC_APB1RSTR_CAN1RST, STM32_RCC_APB1RSTR);
+}
+
+/****************************************************************************
+ * Name: board_get_product_name
+ *
+ * Description:
+ *   Called to retrieve the product name. The returned value is a assumed
+ *   to be written to a pascal style string that will be length prefixed
+ *   and not null terminated
+ *
+ * Input Parameters:
+ *    product_name - A pointer to a buffer to write the name.
+ *    maxlen       - The maximum number of charter that can be written
+ *
+ * Returned Value:
+ *   The length of characters written to the buffer.
+ *
+ ****************************************************************************/
+
+uint8_t board_get_product_name(uint8_t *product_name, size_t maxlen)
+{
+	DEBUGASSERT(maxlen > UAVCAN_STRLEN(HW_UAVCAN_NAME));
+	memcpy(product_name, HW_UAVCAN_NAME, UAVCAN_STRLEN(HW_UAVCAN_NAME));
+	return UAVCAN_STRLEN(HW_UAVCAN_NAME);
+}
+
+/****************************************************************************
+ * Name: board_get_hardware_version
+ *
+ * Description:
+ *   Called to retrieve the hardware version information. The function
+ *   will first initialize the the callers struct to all zeros.
+ *
+ * Input Parameters:
+ *    hw_version - A pointer to a uavcan_hardwareversion_t.
+ *
+ * Returned Value:
+ *   Length of the unique_id
+ *
+ ****************************************************************************/
+
+size_t board_get_hardware_version(uavcan_HardwareVersion_t *hw_version)
+{
+	memset(hw_version, 0, sizeof(uavcan_HardwareVersion_t));
+
+	hw_version->major = HW_VERSION_MAJOR;
+	hw_version->minor = HW_VERSION_MINOR;
+
+	return board_get_mfguid(*(mfguid_t *) hw_version->unique_id);
+}
+
+/****************************************************************************
+ * Name: board_indicate
+ *
+ * Description:
+ *   Provides User feedback to indicate the state of the bootloader
+ *   on board specific  hardware.
+ *
+ * Input Parameters:
+ *    indication - A member of the uiindication_t
+ *
+ * Returned Value:
+ *   None
+ *
+ ****************************************************************************/
+#define led(n, code, r , g , b, h) {.red = (r),.green = (g), .blue = (b),.hz = (h)}
+
+typedef begin_packed_struct struct led_t {
+	uint8_t red;
+	uint8_t green;
+	uint8_t blue;
+	uint8_t hz;
+} end_packed_struct led_t;
+
+static const  led_t i2l[] = {
+
+	led(0, off,                             0,     0,     0,     0),
+	led(1, reset,                          128,   128,   128,   30),
+	led(2, autobaud_start,                  0,   128,     0,     1),
+	led(3, autobaud_end,                    0,   128,     0,     2),
+	led(4, allocation_start,                0,     0,    64,     2),
+	led(5, allocation_end,                  0,   128,    64,     3),
+	led(6, fw_update_start,                32,   128,    64,     3),
+	led(7, fw_update_erase_fail,           32,   128,    32,     3),
+	led(8, fw_update_invalid_response,     64,     0,     0,     1),
+	led(9, fw_update_timeout,              64,     0,     0,     2),
+	led(a, fw_update_invalid_crc,          64,     0,     0,     4),
+	led(b, jump_to_app,                     0,   128,     0,    10),
+
+};
+
+void board_indicate(uiindication_t indication)
+{
+	rgb_led(i2l[indication].red,
+		i2l[indication].green,
+		i2l[indication].blue,
+		i2l[indication].hz);
+}

boards/ark/septentrio-gps/src/boot_config.h

@@ -0,0 +1,130 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/*
+ * @file boot_config.h
+ *
+ * bootloader definitions that configures the behavior and options
+ * of the Boot loader
+ * This file is relies on the parent folder's boot_config.h file and defines
+ * different usages of the hardware for bootloading
+ */
+
+#pragma once
+
+/************************************************************************************
+ * Included Files
+ ************************************************************************************/
+
+/* Bring in the board_config.h definitions
+ * todo:make this be pulled in from a targed's build
+ * files in nuttx*/
+
+#include "board_config.h"
+#include "uavcan.h"
+#include <nuttx/compiler.h>
+
+#include <stdint.h>
+
+#include <stm32_flash.h>
+
+/****************************************************************************
+ * Pre-processor Definitions
+ ****************************************************************************/
+
+#define OPT_PREFERRED_NODE_ID ANY_NODE_ID
+
+//todo:wrap OPT_x in in ifdefs for command line definitions
+#define OPT_TBOOT_MS                    3000
+#define OPT_NODE_STATUS_RATE_MS         800
+#define OPT_NODE_INFO_RATE_MS           50
+#define OPT_BL_NUMBER_TIMERS            7
+
+/*
+ *  This Option set is set to 1 ensure a provider of firmware has an
+ *  opportunity update the node's firmware.
+ *  This Option is the default policy and can be overridden by
+ *  a jumper
+ *  When this Policy is set, the node will ignore tboot and
+ *  wait indefinitely for a GetNodeInfo request before booting.
+ *
+ *  OPT_WAIT_FOR_GETNODEINFO_JUMPER_GPIO_INVERT is used to allow
+ *  the polarity of the jumper to be True Active
+ *
+ *  wait  OPT_WAIT_FOR_GETNODEINFO  OPT_WAIT_FOR_GETNODEINFO_JUMPER_GPIO
+ *                                                 Jumper
+ *   yes           1                       0         x
+ *   yes           1                       1       Active
+ *   no            1                       1       Not Active
+ *   no            0                       0         X
+ *   yes           0                       1       Active
+ *   no            0                       1       Not Active
+ *
+ */
+#define OPT_WAIT_FOR_GETNODEINFO                    0
+#define OPT_WAIT_FOR_GETNODEINFO_JUMPER_GPIO        1
+#define OPT_WAIT_FOR_GETNODEINFO_JUMPER_GPIO_INVERT 1
+
+#define OPT_ENABLE_WD           1
+
+#define OPT_RESTART_TIMEOUT_MS          20000
+
+/* Reserved for the Booloader */
+#define OPT_BOOTLOADER_SIZE_IN_K        (1024*64)
+
+/* Reserved for the application out of the total
+ * system flash minus the BOOTLOADER_SIZE_IN_K
+ */
+#define OPT_APPLICATION_RESERVER_IN_K    0
+
+#define OPT_APPLICATION_IMAGE_OFFSET    OPT_BOOTLOADER_SIZE_IN_K
+#define OPT_APPLICATION_IMAGE_LENGTH    (FLASH_SIZE-(OPT_BOOTLOADER_SIZE_IN_K+OPT_APPLICATION_RESERVER_IN_K))
+
+
+#define FLASH_BASE              STM32_FLASH_BASE
+#define FLASH_SIZE              STM32_FLASH_SIZE
+
+#define APPLICATION_LOAD_ADDRESS (FLASH_BASE + OPT_APPLICATION_IMAGE_OFFSET)
+#define APPLICATION_SIZE (FLASH_SIZE-OPT_APPLICATION_IMAGE_OFFSET)
+#define APPLICATION_LAST_8BIT_ADDRRESS  ((uint8_t *)((APPLICATION_LOAD_ADDRESS+APPLICATION_SIZE)-sizeof(uint8_t)))
+#define APPLICATION_LAST_32BIT_ADDRRESS ((uint32_t *)((APPLICATION_LOAD_ADDRESS+APPLICATION_SIZE)-sizeof(uint32_t)))
+#define APPLICATION_LAST_64BIT_ADDRRESS ((uint64_t *)((APPLICATION_LOAD_ADDRESS+APPLICATION_SIZE)-sizeof(uint64_t)))
+
+/* If this board uses big flash that have large sectors */
+
+#define OPT_USE_YIELD
+
+/* Bootloader Option*****************************************************************
+ *
+ */
+#define GPIO_GETNODEINFO_JUMPER (GPIO_BOOT_CONFIG & ~GPIO_EXTI)

boards/ark/septentrio-gps/src/can.c

@@ -0,0 +1,130 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file can.c
+ *
+ * Board-specific CAN functions.
+ */
+
+/************************************************************************************
+ * Included Files
+ ************************************************************************************/
+
+#include <px4_platform_common/px4_config.h>
+
+#include <errno.h>
+#include <debug.h>
+
+#include <nuttx/can/can.h>
+#include <arch/board/board.h>
+
+#include "chip.h"
+#include "arm_internal.h"
+
+#include "stm32.h"
+#include "stm32_can.h"
+#include "board_config.h"
+
+#ifdef CONFIG_CAN
+
+/************************************************************************************
+ * Pre-processor Definitions
+ ************************************************************************************/
+/* Configuration ********************************************************************/
+
+#if defined(CONFIG_STM32_CAN1) && defined(CONFIG_STM32_CAN2)
+#  warning "Both CAN1 and CAN2 are enabled.  Assuming only CAN1."
+#  undef CONFIG_STM32_CAN2
+#endif
+
+#ifdef CONFIG_STM32_CAN1
+#  define CAN_PORT 1
+#else
+#  define CAN_PORT 2
+#endif
+
+/************************************************************************************
+ * Private Functions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Public Functions
+ ************************************************************************************/
+int can_devinit(void);
+
+/************************************************************************************
+ * Name: can_devinit
+ *
+ * Description:
+ *   All STM32 architectures must provide the following interface to work with
+ *   examples/can.
+ *
+ ************************************************************************************/
+
+int can_devinit(void)
+{
+	static bool initialized = false;
+	struct can_dev_s *can;
+	int ret;
+
+	/* Check if we have already initialized */
+
+	if (!initialized) {
+		/* Call stm32_caninitialize() to get an instance of the CAN interface */
+
+		can = stm32_caninitialize(CAN_PORT);
+
+		if (can == NULL) {
+			canerr("ERROR:  Failed to get CAN interface\n");
+			return -ENODEV;
+		}
+
+		/* Register the CAN driver at "/dev/can0" */
+
+		ret = can_register("/dev/can0", can);
+
+		if (ret < 0) {
+			canerr("ERROR: can_register failed: %d\n", ret);
+			return ret;
+		}
+
+		/* Now we are initialized */
+
+		initialized = true;
+	}
+
+	return OK;
+}
+
+#endif

boards/ark/septentrio-gps/src/i2c.cpp

@@ -0,0 +1,39 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#include <px4_arch/i2c_hw_description.h>
+
+constexpr px4_i2c_bus_t px4_i2c_buses[I2C_BUS_MAX_BUS_ITEMS] = {
+	initI2CBusInternal(1),
+	initI2CBusInternal(2),
+};

boards/ark/septentrio-gps/src/init.c

@@ -0,0 +1,168 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file init.c
+ *
+ * board specific early startup code.  This file implements the
+ * board_app_initialize() function that is called early by nsh during startup.
+ *
+ * Code here is run before the rcS script is invoked; it should start required
+ * subsystems and perform board-specific initialization.
+ */
+
+#include <px4_platform_common/px4_config.h>
+#include <px4_platform_common/tasks.h>
+
+#include <stdbool.h>
+#include <stdio.h>
+#include <string.h>
+#include <debug.h>
+#include <errno.h>
+#include <syslog.h>
+
+#include <nuttx/board.h>
+
+#include <stm32.h>
+#include "board_config.h"
+#include "led.h"
+#include <stm32_uart.h>
+
+#include <arch/board/board.h>
+
+#include <drivers/drv_hrt.h>
+#include <drivers/drv_board_led.h>
+#include <drivers/drv_watchdog.h>
+
+#include <systemlib/px4_macros.h>
+
+#include <px4_platform_common/init.h>
+#include <px4_platform/gpio.h>
+
+# if defined(FLASH_BASED_PARAMS)
+#  include <parameters/flashparams/flashfs.h>
+#endif
+
+/************************************************************************************
+ * Name: stm32_boardinitialize
+ *
+ * Description:
+ *   All STM32 architectures must provide the following entry point.  This entry point
+ *   is called early in the initialization -- after all memory has been configured
+ *   and mapped but before any devices have been initialized.
+ *
+ ************************************************************************************/
+
+__EXPORT void stm32_boardinitialize(void)
+{
+	watchdog_init();
+
+	/* configure pins */
+	const uint32_t gpio[] = PX4_GPIO_INIT_LIST;
+	px4_gpio_init(gpio, arraySize(gpio));
+
+	// Configure SPI all interfaces GPIO & enable power.
+	stm32_spiinitialize();
+
+	// Check if button is held. If so go into gps passthrough mode
+	if (stm32_gpioread(GPIO_BTN_SAFETY)) {
+		rgb_led(128, 128, 128, 10);
+		stm32_configgpio(GPIO_USART1_TX_GPIO);
+		stm32_configgpio(GPIO_USART1_RX_GPIO);
+		stm32_configgpio(GPIO_USART2_TX_GPIO);
+		stm32_configgpio(GPIO_USART2_RX_GPIO);
+
+		while (1) {
+			watchdog_pet();
+			stm32_gpiowrite(GPIO_USART2_TX_GPIO, stm32_gpioread(GPIO_USART1_RX_GPIO));
+			stm32_gpiowrite(GPIO_USART1_TX_GPIO, stm32_gpioread(GPIO_USART2_RX_GPIO));
+		}
+	}
+}
+
+/****************************************************************************
+ * Name: board_app_initialize
+ *
+ * Description:
+ *   Perform application specific initialization.  This function is never
+ *   called directly from application code, but only indirectly via the
+ *   (non-standard) boardctl() interface using the command BOARDIOC_INIT.
+ *
+ * Input Parameters:
+ *   arg - The boardctl() argument is passed to the board_app_initialize()
+ *         implementation without modification.  The argument has no
+ *         meaning to NuttX; the meaning of the argument is a contract
+ *         between the board-specific initalization logic and the the
+ *         matching application logic.  The value cold be such things as a
+ *         mode enumeration value, a set of DIP switch switch settings, a
+ *         pointer to configuration data read from a file or serial FLASH,
+ *         or whatever you would like to do with it.  Every implementation
+ *         should accept zero/NULL as a default configuration.
+ *
+ * Returned Value:
+ *   Zero (OK) is returned on success; a negated errno value is returned on
+ *   any failure to indicate the nature of the failure.
+ *
+ ****************************************************************************/
+
+__EXPORT int board_app_initialize(uintptr_t arg)
+{
+	px4_platform_init();
+
+#if defined(SERIAL_HAVE_RXDMA)
+	// set up the serial DMA polling at 1ms intervals for received bytes that have not triggered a DMA event.
+	static struct hrt_call serial_dma_call;
+	hrt_call_every(&serial_dma_call, 1000, 1000, (hrt_callout)stm32_serial_dma_poll, NULL);
+#endif
+
+#if defined(FLASH_BASED_PARAMS)
+	static sector_descriptor_t params_sector_map[] = {
+		{2, 16 * 1024, 0x08008000},
+		{3, 16 * 1024, 0x0800C000},
+		{0, 0, 0},
+	};
+
+	/* Initialize the flashfs layer to use heap allocated memory */
+	int result = parameter_flashfs_init(params_sector_map, NULL, 0);
+
+	if (result != OK) {
+		syslog(LOG_ERR, "[boot] FAILED to init params in FLASH %d\n", result);
+	}
+
+#endif // FLASH_BASED_PARAMS
+
+	/* Configure the HW based on the manifest */
+	//px4_platform_configure();
+
+	return OK;
+}

boards/ark/septentrio-gps/src/led.c

@@ -0,0 +1,124 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file led.c
+ *
+ * LED backend.
+ */
+
+#include <px4_platform_common/px4_config.h>
+
+#include <stdbool.h>
+
+#include "chip.h"
+#include "stm32_gpio.h"
+#include "board_config.h"
+
+#include <nuttx/board.h>
+#include <arch/board/board.h>
+
+#include "led.h"
+
+#define TMR_BASE        STM32_TIM1_BASE
+#define TMR_FREQUENCY   STM32_APB2_TIM1_CLKIN
+#define TMR_REG(o)      (TMR_BASE+(o))
+
+void rgb_led(int r, int g, int b, int freqs)
+{
+
+	long fosc = TMR_FREQUENCY;
+	long prescale = 2048;
+	long p1s = fosc / prescale;
+	long p0p5s  = p1s / 2;
+	uint16_t val;
+	static bool once = 0;
+
+	if (!once) {
+		once = 1;
+
+		/* Enabel Clock to Block */
+		modifyreg32(STM32_RCC_APB2ENR, 0, RCC_APB2ENR_TIM1EN);
+
+		/* Reload */
+
+		val = getreg16(TMR_REG(STM32_BTIM_EGR_OFFSET));
+		val |= ATIM_EGR_UG;
+		putreg16(val, TMR_REG(STM32_BTIM_EGR_OFFSET));
+
+		/* Set Prescaler STM32_TIM_SETCLOCK */
+
+		putreg16(prescale, TMR_REG(STM32_BTIM_PSC_OFFSET));
+
+		/* Enable STM32_TIM_SETMODE*/
+
+		putreg16(ATIM_CR1_CEN | ATIM_CR1_ARPE, TMR_REG(STM32_BTIM_CR1_OFFSET));
+
+
+		putreg16((ATIM_CCMR_MODE_PWM1 << ATIM_CCMR1_OC1M_SHIFT) | ATIM_CCMR1_OC1PE |
+			 (ATIM_CCMR_MODE_PWM1 << ATIM_CCMR1_OC2M_SHIFT) | ATIM_CCMR1_OC2PE, TMR_REG(STM32_GTIM_CCMR1_OFFSET));
+		putreg16((ATIM_CCMR_MODE_PWM1 << ATIM_CCMR2_OC3M_SHIFT) | ATIM_CCMR2_OC3PE, TMR_REG(STM32_GTIM_CCMR2_OFFSET));
+		putreg16(ATIM_CCER_CC3E | ATIM_CCER_CC3P |
+			 ATIM_CCER_CC2E | ATIM_CCER_CC2P |
+			 ATIM_CCER_CC1E | ATIM_CCER_CC1P, TMR_REG(STM32_GTIM_CCER_OFFSET));
+
+
+		stm32_configgpio(GPIO_TIM1_CH1);
+		stm32_configgpio(GPIO_TIM1_CH2);
+		stm32_configgpio(GPIO_TIM1_CH3);
+
+		/* master output enable = on */
+		putreg16(ATIM_BDTR_MOE, (TMR_REG(STM32_ATIM_BDTR_OFFSET)));
+	}
+
+	long p  = freqs == 0 ? p1s : p1s / freqs;
+	putreg32(p, TMR_REG(STM32_BTIM_ARR_OFFSET));
+
+	p  = freqs == 0 ? p1s + 1 : p0p5s / freqs;
+
+	putreg32((r * p) / 255, TMR_REG(STM32_GTIM_CCR1_OFFSET));
+	putreg32((g * p) / 255, TMR_REG(STM32_GTIM_CCR2_OFFSET));
+	putreg32((b * p) / 255, TMR_REG(STM32_GTIM_CCR3_OFFSET));
+
+	val = getreg16(TMR_REG(STM32_BTIM_CR1_OFFSET));
+
+	if (freqs == 0) {
+		val &= ~ATIM_CR1_CEN;
+
+	} else {
+		val |= ATIM_CR1_CEN;
+	}
+
+	putreg16(val, TMR_REG(STM32_BTIM_CR1_OFFSET));
+
+}

boards/ark/septentrio-gps/src/led.h

@@ -0,0 +1,37 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2015 PX4 Development Team. All rights reserved.
+ *   Author: David Sidrane<david_s5@nscdg.com>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+__BEGIN_DECLS
+void rgb_led(int r, int g, int b, int freqs);
+__END_DECLS

boards/ark/septentrio-gps/src/spi.cpp

@@ -0,0 +1,44 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#include <px4_arch/spi_hw_description.h>
+#include <drivers/drv_sensor.h>
+#include <nuttx/spi/spi.h>
+
+constexpr px4_spi_bus_t px4_spi_buses[SPI_BUS_MAX_BUS_ITEMS] = {
+	initSPIBus(SPI::Bus::SPI1, {
+		initSPIDevice(DRV_IMU_DEVTYPE_ICM42688P, SPI::CS{GPIO::PortB, GPIO::Pin0}, SPI::DRDY{GPIO::PortB, GPIO::Pin1}),
+	}),
+};
+
+static constexpr bool unused = validateSPIConfig(px4_spi_buses);

boards/ark/septentrio-gps/uavcan_board_identity

@@ -0,0 +1,17 @@
+# UAVCAN boot loadable Module ID
+set(uavcanblid_sw_version_major ${PX4_VERSION_MAJOR})
+set(uavcanblid_sw_version_minor ${PX4_VERSION_MINOR})
+add_definitions(
+	-DAPP_VERSION_MAJOR=${uavcanblid_sw_version_major}
+	-DAPP_VERSION_MINOR=${uavcanblid_sw_version_minor}
+)
+
+set(uavcanblid_hw_version_major 0)
+set(uavcanblid_hw_version_minor 84)
+set(uavcanblid_name "\"org.ark.septentrio-gps\"")
+
+add_definitions(
+	-DHW_UAVCAN_NAME=${uavcanblid_name}
+	-DHW_VERSION_MAJOR=${uavcanblid_hw_version_major}
+	-DHW_VERSION_MINOR=${uavcanblid_hw_version_minor}
+)

boards/atl/mantis-edu/src/board_config.h

@@ -64,9 +64,6 @@
 // Hacks for MAVLink RC button input
 #define ATL_MANTIS_RC_INPUT_HACKS
 
-// Hacks for MAVLink RC button input
-#define ATL_MANTIS_RC_INPUT_HACKS
-
 /*
  * ADC channels
  *

boards/modalai/voxl2-slpi/default.px4board

@@ -4,13 +4,13 @@ CONFIG_DRIVERS_ACTUATORS_VOXL_ESC=y
 CONFIG_DRIVERS_BAROMETER_INVENSENSE_ICP101XX=y
 CONFIG_DRIVERS_DISTANCE_SENSOR_VL53L0X=y
 CONFIG_DRIVERS_DISTANCE_SENSOR_VL53L1X=y
+CONFIG_DRIVERS_IMU_INVENSENSE_ICM42688P=y
 CONFIG_DRIVERS_LIGHTS_RGBLED_NCP5623C=y
 CONFIG_DRIVERS_MAGNETOMETER_ISENTEK_IST8308=y
 CONFIG_DRIVERS_MAGNETOMETER_ISENTEK_IST8310=y
 CONFIG_DRIVERS_MAGNETOMETER_QMC5883L=y
 CONFIG_DRIVERS_POWER_MONITOR_VOXLPM=y
 CONFIG_DRIVERS_QSHELL_QURT=y
-CONFIG_DRIVERS_VOXL2_IO=y
 CONFIG_MODULES_COMMANDER=y
 CONFIG_MODULES_CONTROL_ALLOCATOR=y
 CONFIG_MODULES_EKF2=y
@@ -28,4 +28,5 @@ CONFIG_MODULES_RC_UPDATE=y
 CONFIG_MODULES_SENSORS=y
 CONFIG_MODULES_SIMULATION_PWM_OUT_SIM=y
 CONFIG_SYSTEMCMDS_UORB=y
+CONFIG_SYSTEMCMDS_PARAM=y
 CONFIG_ORB_COMMUNICATOR=y

boards/modalai/voxl2-slpi/src/CMakeLists.txt

@@ -44,11 +44,10 @@ add_library(drivers_board
     )
 
 # Add custom drivers for SLPI
-# add_subdirectory(${PX4_BOARD_DIR}/src/drivers/icm42688p)
 add_subdirectory(${PX4_BOARD_DIR}/src/drivers/rc_controller)
 add_subdirectory(${PX4_BOARD_DIR}/src/drivers/mavlink_rc_in)
 # add_subdirectory(${PX4_BOARD_DIR}/src/drivers/spektrum_rc)
 # add_subdirectory(${PX4_BOARD_DIR}/src/drivers/ghst_rc)
-# add_subdirectory(${PX4_BOARD_DIR}/src/drivers/dsp_hitl)
+add_subdirectory(${PX4_BOARD_DIR}/src/drivers/dsp_hitl)
 # add_subdirectory(${PX4_BOARD_DIR}/src/drivers/dsp_sbus)
 add_subdirectory(${PX4_BOARD_DIR}/src/drivers/elrs_led)

boards/modalai/voxl2-slpi/src/drivers/dsp_hitl/dsp_hitl.cpp

@@ -989,10 +989,10 @@ handle_message_hil_gps_dsp(mavlink_message_t *msg)
 
 	gps.device_id = device_id.devid;
 
-	gps.lat = hil_gps.lat;
-	gps.lon = hil_gps.lon;
-	gps.alt = hil_gps.alt;
-	gps.alt_ellipsoid = hil_gps.alt;
+	gps.latitude_deg = hil_gps.lat;
+	gps.longitude_deg = hil_gps.lon;
+	gps.altitude_msl_m = hil_gps.alt;
+	gps.altitude_ellipsoid_m = hil_gps.alt;
 
 	gps.s_variance_m_s = 0.25f;
 	gps.c_variance_rad = 0.5f;

boards/modalai/voxl2-slpi/src/drivers/icm42688p/ICM42688P.cpp

@@ -1,991 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (c) 2020 PX4 Development Team. All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name PX4 nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-#include "ICM42688P.hpp"
-
-bool hitl_mode = false;
-
-using namespace time_literals;
-
-static constexpr int16_t combine(uint8_t msb, uint8_t lsb)
-{
-	return (msb << 8u) | lsb;
-}
-
-ICM42688P::ICM42688P(const I2CSPIDriverConfig &config) :
-	// SPI(DRV_IMU_DEVTYPE_ICM42688P, MODULE_NAME, bus, device, spi_mode, bus_frequency),
-	// I2CSPIDriver(MODULE_NAME, px4::device_bus_to_wq(get_device_id()), bus_option, bus),
-	// _drdy_gpio(drdy_gpio)
-	SPI(config),
-	I2CSPIDriver(config),
-	_drdy_gpio(config.drdy_gpio),
-	_px4_accel(get_device_id(), config.rotation),
-	_px4_gyro(get_device_id(), config.rotation)
-{
-	if (config.drdy_gpio != 0) {
-		_drdy_missed_perf = perf_alloc(PC_COUNT, MODULE_NAME": DRDY missed");
-	}
-
-	if (!hitl_mode) {
-		// _px4_accel = std::make_shared<PX4Accelerometer>(get_device_id(), rotation);
-		// _px4_gyro = std::make_shared<PX4Gyroscope>(get_device_id(), rotation);
-		ConfigureSampleRate(_px4_gyro.get_max_rate_hz());
-		// _imu_server_pub.advertise();
-
-	} else {
-		ConfigureSampleRate(0);
-	}
-}
-
-ICM42688P::~ICM42688P()
-{
-	perf_free(_bad_register_perf);
-	perf_free(_bad_transfer_perf);
-	perf_free(_fifo_empty_perf);
-	perf_free(_fifo_overflow_perf);
-	perf_free(_fifo_reset_perf);
-	perf_free(_drdy_missed_perf);
-
-	// if (!hitl_mode){
-	//  		_imu_server_pub.unadvertise();
-	// }
-}
-
-int ICM42688P::init()
-{
-	int ret = SPI::init();
-
-	if (ret != PX4_OK) {
-		DEVICE_DEBUG("SPI::init failed (%i)", ret);
-		return ret;
-	}
-
-	return Reset() ? 0 : -1;
-}
-
-bool ICM42688P::Reset()
-{
-	_state = STATE::RESET;
-	DataReadyInterruptDisable();
-	ScheduleClear();
-	ScheduleNow();
-	return true;
-}
-
-void ICM42688P::exit_and_cleanup()
-{
-	DataReadyInterruptDisable();
-	I2CSPIDriverBase::exit_and_cleanup();
-}
-
-void ICM42688P::print_status()
-{
-	I2CSPIDriverBase::print_status();
-
-	PX4_INFO("FIFO empty interval: %d us (%.1f Hz)", _fifo_empty_interval_us, 1e6 / _fifo_empty_interval_us);
-
-	perf_print_counter(_bad_register_perf);
-	perf_print_counter(_bad_transfer_perf);
-	perf_print_counter(_fifo_empty_perf);
-	perf_print_counter(_fifo_overflow_perf);
-	perf_print_counter(_fifo_reset_perf);
-	perf_print_counter(_drdy_missed_perf);
-}
-
-int ICM42688P::probe()
-{
-	for (int i = 0; i < 3; i++) {
-		uint8_t whoami = RegisterRead(Register::BANK_0::WHO_AM_I);
-
-		if (whoami == WHOAMI) {
-			PX4_INFO("ICM42688P::probe successful!");
-			return PX4_OK;
-
-		} else {
-			DEVICE_DEBUG("unexpected WHO_AM_I 0x%02x", whoami);
-
-			uint8_t reg_bank_sel = RegisterRead(Register::BANK_0::REG_BANK_SEL);
-			int bank = reg_bank_sel >> 4;
-
-			if (bank >= 1 && bank <= 3) {
-				DEVICE_DEBUG("incorrect register bank for WHO_AM_I REG_BANK_SEL:0x%02x, bank:%d", reg_bank_sel, bank);
-				// force bank selection and retry
-				SelectRegisterBank(REG_BANK_SEL_BIT::USER_BANK_0, true);
-			}
-		}
-	}
-
-	return PX4_ERROR;
-}
-
-void ICM42688P::RunImpl()
-{
-	PX4_INFO(">>> ICM42688P this: %p", this);
-
-	const hrt_abstime now = hrt_absolute_time();
-
-	switch (_state) {
-	case STATE::RESET:
-		// DEVICE_CONFIG: Software reset configuration
-		RegisterWrite(Register::BANK_0::DEVICE_CONFIG, DEVICE_CONFIG_BIT::SOFT_RESET_CONFIG);
-		_reset_timestamp = now;
-		_failure_count = 0;
-		_state = STATE::WAIT_FOR_RESET;
-		ScheduleDelayed(2_ms); // to be safe wait 2 ms for soft reset to be effective
-		break;
-
-	case STATE::WAIT_FOR_RESET:
-		if ((RegisterRead(Register::BANK_0::WHO_AM_I) == WHOAMI)
-		    && (RegisterRead(Register::BANK_0::DEVICE_CONFIG) == 0x00)
-		    && (RegisterRead(Register::BANK_0::INT_STATUS) & INT_STATUS_BIT::RESET_DONE_INT)) {
-
-			_state = STATE::CONFIGURE;
-			ScheduleDelayed(10_ms); // 30 ms gyro startup time, 10 ms accel from sleep to valid data
-
-		} else {
-			// RESET not complete
-			if (hrt_elapsed_time(&_reset_timestamp) > 1000_ms) {
-				PX4_DEBUG("Reset failed, retrying");
-				_state = STATE::RESET;
-				ScheduleDelayed(100_ms);
-
-			} else {
-				PX4_DEBUG("Reset not complete, check again in 10 ms");
-				ScheduleDelayed(10_ms);
-			}
-		}
-
-		break;
-
-	case STATE::CONFIGURE:
-
-		if (Configure()) {
-
-			// Wakeup accel and gyro after configuring registers
-			ScheduleDelayed(1_ms); // add a delay here to be safe
-			RegisterWrite(Register::BANK_0::PWR_MGMT0, PWR_MGMT0_BIT::GYRO_MODE_LOW_NOISE | PWR_MGMT0_BIT::ACCEL_MODE_LOW_NOISE);
-			ScheduleDelayed(30_ms); // 30 ms gyro startup time, 10 ms accel from sleep to valid data
-
-			// if configure succeeded then start reading from FIFO
-			_state = STATE::FIFO_READ;
-
-			if (DataReadyInterruptConfigure()) {
-				_data_ready_interrupt_enabled = true;
-
-				// backup schedule as a watchdog timeout
-				ScheduleDelayed(100_ms);
-
-			} else {
-				PX4_ERR("ICM42688P::RunImpl interrupt configuration failed");
-
-				_data_ready_interrupt_enabled = false;
-				ScheduleOnInterval(_fifo_empty_interval_us, _fifo_empty_interval_us);
-			}
-
-			FIFOReset();
-
-		} else {
-
-			PX4_ERR("ICM42688P::RunImpl configuration failed");
-
-			// CONFIGURE not complete
-			if (hrt_elapsed_time(&_reset_timestamp) > 1000_ms) {
-				PX4_DEBUG("Configure failed, resetting");
-				_state = STATE::RESET;
-
-			} else {
-				PX4_DEBUG("Configure failed, retrying");
-			}
-
-			ScheduleDelayed(100_ms);
-		}
-
-		break;
-
-	case STATE::FIFO_READ: {
-#ifndef __PX4_QURT
-			uint32_t samples = 0;
-
-			if (_data_ready_interrupt_enabled) {
-				// scheduled from interrupt if _drdy_fifo_read_samples was set as expected
-				if (_drdy_fifo_read_samples.fetch_and(0) != _fifo_gyro_samples) {
-					perf_count(_drdy_missed_perf);
-
-				} else {
-					samples = _fifo_gyro_samples;
-				}
-
-				// push backup schedule back
-				ScheduleDelayed(_fifo_empty_interval_us * 2);
-			}
-
-			if (samples == 0) {
-				// check current FIFO count
-				const uint16_t fifo_count = FIFOReadCount();
-
-				if (fifo_count >= FIFO::SIZE) {
-					FIFOReset();
-					perf_count(_fifo_overflow_perf);
-
-				} else if (fifo_count == 0) {
-					perf_count(_fifo_empty_perf);
-
-				} else {
-					// FIFO count (size in bytes)
-					samples = (fifo_count / sizeof(FIFO::DATA));
-
-					if (samples > FIFO_MAX_SAMPLES) {
-						// not technically an overflow, but more samples than we expected or can publish
-						FIFOReset();
-						perf_count(_fifo_overflow_perf);
-						samples = 0;
-					}
-				}
-			}
-
-			bool success = false;
-
-			if (samples >= 1) {
-				if (FIFORead(now, samples)) {
-					success = true;
-
-					if (_failure_count > 0) {
-						_failure_count--;
-					}
-				}
-			}
-
-			if (!success) {
-				_failure_count++;
-
-				// full reset if things are failing consistently
-				if (_failure_count > 10) {
-					Reset();
-					return;
-				}
-			}
-
-			// check configuration registers periodically or immediately following any failure
-			if (RegisterCheck(_register_bank0_cfg[_checked_register_bank0])
-			    && RegisterCheck(_register_bank1_cfg[_checked_register_bank1])
-			    && RegisterCheck(_register_bank2_cfg[_checked_register_bank2])
-			   ) {
-				_last_config_check_timestamp = now;
-				_checked_register_bank0 = (_checked_register_bank0 + 1) % size_register_bank0_cfg;
-				_checked_register_bank1 = (_checked_register_bank1 + 1) % size_register_bank1_cfg;
-				_checked_register_bank2 = (_checked_register_bank2 + 1) % size_register_bank2_cfg;
-
-			} else {
-				// register check failed, force reset
-				perf_count(_bad_register_perf);
-				Reset();
-			}
-
-#endif
-		}
-
-		break;
-	}
-}
-
-void ICM42688P::ConfigureSampleRate(int sample_rate)
-{
-	if (sample_rate == 0) {
-		sample_rate = 800; // default to 800 Hz
-	}
-
-	// round down to nearest FIFO sample dt
-	const float min_interval = FIFO_SAMPLE_DT;
-	_fifo_empty_interval_us = math::max(roundf((1e6f / (float)sample_rate) / min_interval) * min_interval, min_interval);
-
-	_fifo_gyro_samples = roundf(math::min((float)_fifo_empty_interval_us / (1e6f / GYRO_RATE), (float)FIFO_MAX_SAMPLES));
-
-	// recompute FIFO empty interval (us) with actual gyro sample limit
-	_fifo_empty_interval_us = _fifo_gyro_samples * (1e6f / GYRO_RATE);
-
-	ConfigureFIFOWatermark(_fifo_gyro_samples);
-}
-
-void ICM42688P::ConfigureFIFOWatermark(uint8_t samples)
-{
-	// FIFO watermark threshold in number of bytes
-	const uint16_t fifo_watermark_threshold = samples * sizeof(FIFO::DATA);
-
-	for (auto &r : _register_bank0_cfg) {
-		if (r.reg == Register::BANK_0::FIFO_CONFIG2) {
-			// FIFO_WM[7:0]  FIFO_CONFIG2
-			r.set_bits = fifo_watermark_threshold & 0xFF;
-
-		} else if (r.reg == Register::BANK_0::FIFO_CONFIG3) {
-			// FIFO_WM[11:8] FIFO_CONFIG3
-			r.set_bits = (fifo_watermark_threshold >> 8) & 0x0F;
-		}
-	}
-}
-
-void ICM42688P::SelectRegisterBank(enum REG_BANK_SEL_BIT bank, bool force)
-{
-	if (bank != _last_register_bank || force) {
-		// select BANK_0
-		uint8_t cmd_bank_sel[2] {};
-		cmd_bank_sel[0] = static_cast<uint8_t>(Register::BANK_0::REG_BANK_SEL);
-		cmd_bank_sel[1] = bank;
-		transfer(cmd_bank_sel, cmd_bank_sel, sizeof(cmd_bank_sel));
-
-		_last_register_bank = bank;
-	}
-}
-
-bool ICM42688P::Configure()
-{
-	// first set and clear all configured register bits
-	for (const auto &reg_cfg : _register_bank0_cfg) {
-		RegisterSetAndClearBits(reg_cfg.reg, reg_cfg.set_bits, reg_cfg.clear_bits);
-	}
-
-	for (const auto &reg_cfg : _register_bank1_cfg) {
-		RegisterSetAndClearBits(reg_cfg.reg, reg_cfg.set_bits, reg_cfg.clear_bits);
-	}
-
-	for (const auto &reg_cfg : _register_bank2_cfg) {
-		RegisterSetAndClearBits(reg_cfg.reg, reg_cfg.set_bits, reg_cfg.clear_bits);
-	}
-
-	// now check that all are configured
-	bool success = true;
-
-	for (const auto &reg_cfg : _register_bank0_cfg) {
-		if (!RegisterCheck(reg_cfg)) {
-			success = false;
-		}
-	}
-
-	for (const auto &reg_cfg : _register_bank1_cfg) {
-		if (!RegisterCheck(reg_cfg)) {
-			success = false;
-		}
-	}
-
-	for (const auto &reg_cfg : _register_bank2_cfg) {
-		if (!RegisterCheck(reg_cfg)) {
-			success = false;
-		}
-	}
-
-	// // 20-bits data format used
-	// //  the only FSR settings that are operational are ±2000dps for gyroscope and ±16g for accelerometer
-	if (!hitl_mode) {
-		_px4_accel.set_range(16.f * CONSTANTS_ONE_G);
-		_px4_accel.set_scale(CONSTANTS_ONE_G / 8192.f);
-		_px4_gyro.set_range(math::radians(2000.f));
-		_px4_gyro.set_scale(math::radians(1.f / 131.f));
-	}
-
-	return success;
-}
-
-static bool interrupt_debug = false;
-static uint32_t interrupt_debug_count = 0;
-static const uint32_t interrupt_debug_trigger = 800;
-static hrt_abstime last_interrupt_time = 0;
-static hrt_abstime avg_interrupt_delta = 0;
-static hrt_abstime max_interrupt_delta = 0;
-static hrt_abstime min_interrupt_delta = 60 * 1000 * 1000;
-static hrt_abstime cumulative_interrupt_delta = 0;
-
-int ICM42688P::DataReadyInterruptCallback(int irq, void *context, void *arg)
-{
-	hrt_abstime current_interrupt_time = hrt_absolute_time();
-
-	if (interrupt_debug) {
-		if (last_interrupt_time) {
-			hrt_abstime interrupt_delta_time = current_interrupt_time - last_interrupt_time;
-
-			if (interrupt_delta_time > max_interrupt_delta) { max_interrupt_delta = interrupt_delta_time; }
-
-			if (interrupt_delta_time < min_interrupt_delta) { min_interrupt_delta = interrupt_delta_time; }
-
-			cumulative_interrupt_delta += interrupt_delta_time;
-		}
-
-		last_interrupt_time = current_interrupt_time;
-
-		interrupt_debug_count++;
-
-		if (interrupt_debug_count == interrupt_debug_trigger) {
-			avg_interrupt_delta = cumulative_interrupt_delta / interrupt_debug_trigger;
-			PX4_INFO(">>> Max: %llu, Min: %llu, Avg: %llu", max_interrupt_delta,
-				 min_interrupt_delta, avg_interrupt_delta);
-			interrupt_debug_count = 0;
-			cumulative_interrupt_delta = 0;
-		}
-	}
-
-	static_cast<ICM42688P *>(arg)->DataReady();
-
-	return 0;
-}
-
-void ICM42688P::DataReady()
-{
-#ifndef __PX4_QURT
-	uint32_t expected = 0;
-
-	if (_drdy_fifo_read_samples.compare_exchange(&expected, _fifo_gyro_samples)) {
-		ScheduleNow();
-	}
-
-#else
-	uint16_t fifo_byte_count = FIFOReadCount();
-
-	FIFORead(hrt_absolute_time(), fifo_byte_count / sizeof(FIFO::DATA));
-#endif
-}
-
-bool ICM42688P::DataReadyInterruptConfigure()
-{
-	if (_drdy_gpio == 0) {
-		return false;
-	}
-
-	// Setup data ready on falling edge
-	return px4_arch_gpiosetevent(_drdy_gpio, false, true, true, &DataReadyInterruptCallback, this) == 0;
-}
-
-bool ICM42688P::DataReadyInterruptDisable()
-{
-	if (_drdy_gpio == 0) {
-		return false;
-	}
-
-	return px4_arch_gpiosetevent(_drdy_gpio, false, false, false, nullptr, nullptr) == 0;
-}
-
-template <typename T>
-bool ICM42688P::RegisterCheck(const T &reg_cfg)
-{
-	bool success = true;
-
-	const uint8_t reg_value = RegisterRead(reg_cfg.reg);
-
-	if (reg_cfg.set_bits && ((reg_value & reg_cfg.set_bits) != reg_cfg.set_bits)) {
-		PX4_DEBUG("0x%02hhX: 0x%02hhX (0x%02hhX not set)", (uint8_t)reg_cfg.reg, reg_value, reg_cfg.set_bits);
-		success = false;
-	}
-
-	if (reg_cfg.clear_bits && ((reg_value & reg_cfg.clear_bits) != 0)) {
-		PX4_DEBUG("0x%02hhX: 0x%02hhX (0x%02hhX not cleared)", (uint8_t)reg_cfg.reg, reg_value, reg_cfg.clear_bits);
-		success = false;
-	}
-
-	return success;
-}
-
-template <typename T>
-uint8_t ICM42688P::RegisterRead(T reg)
-{
-	uint8_t cmd[2] {};
-	cmd[0] = static_cast<uint8_t>(reg) | DIR_READ;
-	SelectRegisterBank(reg);
-	transfer(cmd, cmd, sizeof(cmd));
-	return cmd[1];
-}
-
-template <typename T>
-void ICM42688P::RegisterWrite(T reg, uint8_t value)
-{
-	uint8_t cmd[2] { (uint8_t)reg, value };
-	SelectRegisterBank(reg);
-	transfer(cmd, cmd, sizeof(cmd));
-}
-
-template <typename T>
-void ICM42688P::RegisterSetAndClearBits(T reg, uint8_t setbits, uint8_t clearbits)
-{
-	const uint8_t orig_val = RegisterRead(reg);
-
-	uint8_t val = (orig_val & ~clearbits) | setbits;
-
-	if (orig_val != val) {
-		RegisterWrite(reg, val);
-	}
-}
-
-uint16_t ICM42688P::FIFOReadCount()
-{
-	// read FIFO count
-	uint8_t fifo_count_buf[3] {};
-	fifo_count_buf[0] = static_cast<uint8_t>(Register::BANK_0::FIFO_COUNTH) | DIR_READ;
-	SelectRegisterBank(REG_BANK_SEL_BIT::USER_BANK_0);
-
-	if (transfer(fifo_count_buf, fifo_count_buf, sizeof(fifo_count_buf)) != PX4_OK) {
-		perf_count(_bad_transfer_perf);
-		return 0;
-	}
-
-	return combine(fifo_count_buf[1], fifo_count_buf[2]);
-}
-
-// static uint32_t debug_decimator = 0;
-// static hrt_abstime last_sample_time = 0;
-// static bool imu_debug = true;
-
-bool ICM42688P::FIFORead(const hrt_abstime &timestamp_sample, uint16_t samples)
-{
-	FIFOTransferBuffer buffer{};
-	const size_t max_transfer_size = 10 * sizeof(FIFO::DATA) + 4;
-	const size_t transfer_size = math::min(samples * sizeof(FIFO::DATA) + 4, max_transfer_size);
-	SelectRegisterBank(REG_BANK_SEL_BIT::USER_BANK_0);
-
-	if (transfer((uint8_t *)&buffer, (uint8_t *)&buffer, transfer_size) != PX4_OK) {
-		perf_count(_bad_transfer_perf);
-		return false;
-	}
-
-	if (buffer.INT_STATUS & INT_STATUS_BIT::FIFO_FULL_INT) {
-		perf_count(_fifo_overflow_perf);
-		FIFOReset();
-		return false;
-	}
-
-	const uint16_t fifo_count_bytes = combine(buffer.FIFO_COUNTH, buffer.FIFO_COUNTL);
-
-	if (fifo_count_bytes >= FIFO::SIZE) {
-		perf_count(_fifo_overflow_perf);
-		FIFOReset();
-		return false;
-	}
-
-	const uint16_t fifo_count_samples = fifo_count_bytes / sizeof(FIFO::DATA);
-
-	if (fifo_count_samples == 0) {
-		perf_count(_fifo_empty_perf);
-		return false;
-	}
-
-	// check FIFO header in every sample
-	uint16_t valid_samples = 0;
-
-	// for (int i = 0; i < math::min(samples, fifo_count_samples); i++) {
-	for (int i = 0; i < math::min(samples, (uint16_t) 10); i++) {
-		bool valid = true;
-
-		// With FIFO_ACCEL_EN and FIFO_GYRO_EN header should be 8’b_0110_10xx
-		const uint8_t FIFO_HEADER = buffer.f[i].FIFO_Header;
-
-		if (FIFO_HEADER & FIFO::FIFO_HEADER_BIT::HEADER_MSG) {
-			// FIFO sample empty if HEADER_MSG set
-			valid = false;
-
-		} else if (!(FIFO_HEADER & FIFO::FIFO_HEADER_BIT::HEADER_ACCEL)) {
-			// accel bit not set
-			valid = false;
-
-		} else if (!(FIFO_HEADER & FIFO::FIFO_HEADER_BIT::HEADER_GYRO)) {
-			// gyro bit not set
-			valid = false;
-
-		} else if (!(FIFO_HEADER & FIFO::FIFO_HEADER_BIT::HEADER_20)) {
-			// Packet does not contain a new and valid extended 20-bit data
-			valid = false;
-
-		} else if (FIFO_HEADER & FIFO::FIFO_HEADER_BIT::HEADER_ODR_ACCEL) {
-			// accel ODR changed
-			valid = false;
-
-		} else if (FIFO_HEADER & FIFO::FIFO_HEADER_BIT::HEADER_ODR_GYRO) {
-			// gyro ODR changed
-			valid = false;
-		}
-
-		if (valid) {
-			valid_samples++;
-
-		} else {
-			perf_count(_bad_transfer_perf);
-			break;
-		}
-	}
-
-	// if (imu_debug) {
-	// 	debug_decimator++;
-	// 	if (debug_decimator == 801) {
-	// 		debug_decimator = 0;
-	// 		PX4_INFO("Initial: %u Next: %u Valid: %u Delta: %llu", samples, fifo_count_samples, valid_samples, timestamp_sample - last_sample_time);
-	// 	}
-	// 	last_sample_time = timestamp_sample;
-	// }
-
-	if (valid_samples > 0) {
-		if (ProcessTemperature(buffer.f, valid_samples)) {
-			ProcessGyro(timestamp_sample, buffer.f, valid_samples);
-			ProcessAccel(timestamp_sample, buffer.f, valid_samples);
-			ProcessIMU(timestamp_sample, buffer.f, valid_samples);
-			return true;
-		}
-	}
-
-	return false;
-}
-
-void ICM42688P::FIFOReset()
-{
-	perf_count(_fifo_reset_perf);
-
-	// SIGNAL_PATH_RESET: FIFO flush
-	RegisterSetBits(Register::BANK_0::SIGNAL_PATH_RESET, SIGNAL_PATH_RESET_BIT::FIFO_FLUSH);
-
-	// reset while FIFO is disabled
-	_drdy_fifo_read_samples.store(0);
-}
-
-static constexpr int32_t reassemble_20bit(const uint32_t a, const uint32_t b, const uint32_t c)
-{
-	// 0xXXXAABBC
-	uint32_t high   = ((a << 12) & 0x000FF000);
-	uint32_t low    = ((b << 4)  & 0x00000FF0);
-	uint32_t lowest = (c         & 0x0000000F);
-
-	uint32_t x = high | low | lowest;
-
-	if (a & Bit7) {
-		// sign extend
-		x |= 0xFFF00000u;
-	}
-
-	return static_cast<int32_t>(x);
-}
-
-void ICM42688P::ProcessIMU(const hrt_abstime &timestamp_sample, const FIFO::DATA fifo[], const uint8_t samples)
-{
-	float accel_x = 0.0, accel_y = 0.0, accel_z = 0.0;
-	float gyro_x = 0.0,  gyro_y = 0.0,  gyro_z = 0.0;
-
-	for (int i = 0; i < samples; i++) {
-		_imu_server_decimator++;
-
-		if (_imu_server_decimator == 8) {
-			_imu_server_decimator = 0;
-			// 20 bit hires mode
-
-			// Sign extension + Accel [19:12] + Accel [11:4] + Accel [3:2] (20 bit extension byte)
-			// Accel data is 18 bit
-			int32_t temp_accel_x = reassemble_20bit(fifo[i].ACCEL_DATA_X1, fifo[i].ACCEL_DATA_X0,
-								fifo[i].Ext_Accel_X_Gyro_X & 0xF0 >> 4);
-			int32_t temp_accel_y = reassemble_20bit(fifo[i].ACCEL_DATA_Y1, fifo[i].ACCEL_DATA_Y0,
-								fifo[i].Ext_Accel_Y_Gyro_Y & 0xF0 >> 4);
-			int32_t temp_accel_z = reassemble_20bit(fifo[i].ACCEL_DATA_Z1, fifo[i].ACCEL_DATA_Z0,
-								fifo[i].Ext_Accel_Z_Gyro_Z & 0xF0 >> 4);
-
-			// Gyro [19:12] + Gyro [11:4] + Gyro [3:0] (bottom 4 bits of 20 bit extension byte)
-			int32_t temp_gyro_x = reassemble_20bit(fifo[i].GYRO_DATA_X1, fifo[i].GYRO_DATA_X0,
-							       fifo[i].Ext_Accel_X_Gyro_X & 0x0F);
-			int32_t temp_gyro_y = reassemble_20bit(fifo[i].GYRO_DATA_Y1, fifo[i].GYRO_DATA_Y0,
-							       fifo[i].Ext_Accel_Y_Gyro_Y & 0x0F);
-			int32_t temp_gyro_z = reassemble_20bit(fifo[i].GYRO_DATA_Z1, fifo[i].GYRO_DATA_Z0,
-							       fifo[i].Ext_Accel_Z_Gyro_Z & 0x0F);
-
-			// accel samples invalid if -524288
-			if (temp_accel_x != -524288 && temp_accel_y != -524288 && temp_accel_z != -524288) {
-				// shift accel by 2 (2 least significant bits are always 0)
-				accel_x = (float) temp_accel_x / 4.f;
-				accel_y = (float) temp_accel_y / 4.f;
-				accel_z = (float) temp_accel_z / 4.f;
-
-				// shift gyro by 1 (least significant bit is always 0)
-				gyro_x = (float) temp_gyro_x / 2.f;
-				gyro_y = (float) temp_gyro_y / 2.f;
-				gyro_z = (float) temp_gyro_z / 2.f;
-
-				// correct frame for publication
-				// sensor's frame is +x forward, +y left, +z up
-				// flip y & z to publish right handed with z down (x forward, y right, z down)
-				accel_y = -accel_y;
-				accel_z = -accel_z;
-				gyro_y  = -gyro_y;
-				gyro_z  = -gyro_z;
-
-				// Scale everything appropriately
-				float accel_scale_factor = (CONSTANTS_ONE_G / 8192.f);
-				accel_x *= accel_scale_factor;
-				accel_y *= accel_scale_factor;
-				accel_z *= accel_scale_factor;
-
-				float gyro_scale_factor = math::radians(1.f / 131.f);
-				gyro_x *= gyro_scale_factor;
-				gyro_y *= gyro_scale_factor;
-				gyro_z *= gyro_scale_factor;
-
-				// Store the data in our array
-				_imu_server_data.accel_x[_imu_server_index] = accel_x;
-				_imu_server_data.accel_y[_imu_server_index] = accel_y;
-				_imu_server_data.accel_z[_imu_server_index] = accel_z;
-				_imu_server_data.gyro_x[_imu_server_index]  = gyro_x;
-				_imu_server_data.gyro_y[_imu_server_index]  = gyro_y;
-				_imu_server_data.gyro_z[_imu_server_index]  = gyro_z;
-				_imu_server_data.ts[_imu_server_index]      = timestamp_sample - (125 * (samples - 1 - i));
-				_imu_server_index++;
-
-				// If array is full, publish the data
-				if (_imu_server_index == 10) {
-					_imu_server_index = 0;
-					_imu_server_data.timestamp = hrt_absolute_time();
-					_imu_server_data.temperature = 0; // Not used right now
-					_imu_server_pub.publish(_imu_server_data);
-				}
-			}
-		}
-	}
-}
-
-void ICM42688P::ProcessAccel(const hrt_abstime &timestamp_sample, const FIFO::DATA fifo[], const uint8_t samples)
-{
-	sensor_accel_fifo_s accel{};
-	accel.timestamp_sample = timestamp_sample;
-	accel.samples = 0;
-	accel.dt = FIFO_SAMPLE_DT;
-
-	// 18-bits of accelerometer data
-	bool scale_20bit = false;
-
-	// first pass
-	for (int i = 0; i < samples; i++) {
-		// 20 bit hires mode
-		// Sign extension + Accel [19:12] + Accel [11:4] + Accel [3:2] (20 bit extension byte)
-		// Accel data is 18 bit ()
-		int32_t accel_x = reassemble_20bit(fifo[i].ACCEL_DATA_X1, fifo[i].ACCEL_DATA_X0,
-						   fifo[i].Ext_Accel_X_Gyro_X & 0xF0 >> 4);
-		int32_t accel_y = reassemble_20bit(fifo[i].ACCEL_DATA_Y1, fifo[i].ACCEL_DATA_Y0,
-						   fifo[i].Ext_Accel_Y_Gyro_Y & 0xF0 >> 4);
-		int32_t accel_z = reassemble_20bit(fifo[i].ACCEL_DATA_Z1, fifo[i].ACCEL_DATA_Z0,
-						   fifo[i].Ext_Accel_Z_Gyro_Z & 0xF0 >> 4);
-
-		// sample invalid if -524288
-		if (accel_x != -524288 && accel_y != -524288 && accel_z != -524288) {
-			// check if any values are going to exceed int16 limits
-			static constexpr int16_t max_accel = INT16_MAX;
-			static constexpr int16_t min_accel = INT16_MIN;
-
-			if (accel_x >= max_accel || accel_x <= min_accel) {
-				scale_20bit = true;
-			}
-
-			if (accel_y >= max_accel || accel_y <= min_accel) {
-				scale_20bit = true;
-			}
-
-			if (accel_z >= max_accel || accel_z <= min_accel) {
-				scale_20bit = true;
-			}
-
-			// shift by 2 (2 least significant bits are always 0)
-			accel.x[accel.samples] = accel_x / 4;
-			accel.y[accel.samples] = accel_y / 4;
-			accel.z[accel.samples] = accel_z / 4;
-			accel.samples++;
-		}
-	}
-
-	if (!scale_20bit) {
-		// if highres enabled accel data is always 8192 LSB/g
-		if (!hitl_mode) {
-			_px4_accel.set_scale(CONSTANTS_ONE_G / 8192.f);
-		}
-
-	} else {
-		// 20 bit data scaled to 16 bit (2^4)
-		for (int i = 0; i < samples; i++) {
-			// 20 bit hires mode
-			// Sign extension + Accel [19:12] + Accel [11:4] + Accel [3:2] (20 bit extension byte)
-			// Accel data is 18 bit ()
-			int16_t accel_x = combine(fifo[i].ACCEL_DATA_X1, fifo[i].ACCEL_DATA_X0);
-			int16_t accel_y = combine(fifo[i].ACCEL_DATA_Y1, fifo[i].ACCEL_DATA_Y0);
-			int16_t accel_z = combine(fifo[i].ACCEL_DATA_Z1, fifo[i].ACCEL_DATA_Z0);
-
-			accel.x[i] = accel_x;
-			accel.y[i] = accel_y;
-			accel.z[i] = accel_z;
-		}
-
-		if (!hitl_mode) {
-			_px4_accel.set_scale(CONSTANTS_ONE_G / 2048.f);
-		}
-	}
-
-	// correct frame for publication
-	for (int i = 0; i < accel.samples; i++) {
-		// sensor's frame is +x forward, +y left, +z up
-		//  flip y & z to publish right handed with z down (x forward, y right, z down)
-		accel.x[i] = accel.x[i];
-		accel.y[i] = (accel.y[i] == INT16_MIN) ? INT16_MAX : -accel.y[i];
-		accel.z[i] = (accel.z[i] == INT16_MIN) ? INT16_MAX : -accel.z[i];
-	}
-
-	if (!hitl_mode) {
-		_px4_accel.set_error_count(perf_event_count(_bad_register_perf) + perf_event_count(_bad_transfer_perf) +
-					   perf_event_count(_fifo_empty_perf) + perf_event_count(_fifo_overflow_perf));
-	}
-
-	if (accel.samples > 0) {
-		if (!hitl_mode) {
-			_px4_accel.updateFIFO(accel);
-		}
-	}
-}
-
-void ICM42688P::ProcessGyro(const hrt_abstime &timestamp_sample, const FIFO::DATA fifo[], const uint8_t samples)
-{
-	sensor_gyro_fifo_s gyro{};
-	gyro.timestamp_sample = timestamp_sample;
-	gyro.samples = 0;
-	gyro.dt = FIFO_SAMPLE_DT;
-
-	// 20-bits of gyroscope data
-	bool scale_20bit = false;
-
-	// first pass
-	for (int i = 0; i < samples; i++) {
-		// 20 bit hires mode
-		// Gyro [19:12] + Gyro [11:4] + Gyro [3:0] (bottom 4 bits of 20 bit extension byte)
-		int32_t gyro_x = reassemble_20bit(fifo[i].GYRO_DATA_X1, fifo[i].GYRO_DATA_X0, fifo[i].Ext_Accel_X_Gyro_X & 0x0F);
-		int32_t gyro_y = reassemble_20bit(fifo[i].GYRO_DATA_Y1, fifo[i].GYRO_DATA_Y0, fifo[i].Ext_Accel_Y_Gyro_Y & 0x0F);
-		int32_t gyro_z = reassemble_20bit(fifo[i].GYRO_DATA_Z1, fifo[i].GYRO_DATA_Z0, fifo[i].Ext_Accel_Z_Gyro_Z & 0x0F);
-
-		// check if any values are going to exceed int16 limits
-		static constexpr int16_t max_gyro = INT16_MAX;
-		static constexpr int16_t min_gyro = INT16_MIN;
-
-		if (gyro_x >= max_gyro || gyro_x <= min_gyro) {
-			scale_20bit = true;
-		}
-
-		if (gyro_y >= max_gyro || gyro_y <= min_gyro) {
-			scale_20bit = true;
-		}
-
-		if (gyro_z >= max_gyro || gyro_z <= min_gyro) {
-			scale_20bit = true;
-		}
-
-		gyro.x[gyro.samples] = gyro_x / 2;
-		gyro.y[gyro.samples] = gyro_y / 2;
-		gyro.z[gyro.samples] = gyro_z / 2;
-		gyro.samples++;
-	}
-
-	if (!scale_20bit) {
-		// if highres enabled gyro data is always 131 LSB/dps
-		if (!hitl_mode) {
-			_px4_gyro.set_scale(math::radians(1.f / 131.f));
-		}
-
-	} else {
-		// 20 bit data scaled to 16 bit (2^4)
-		for (int i = 0; i < samples; i++) {
-			gyro.x[i] = combine(fifo[i].GYRO_DATA_X1, fifo[i].GYRO_DATA_X0);
-			gyro.y[i] = combine(fifo[i].GYRO_DATA_Y1, fifo[i].GYRO_DATA_Y0);
-			gyro.z[i] = combine(fifo[i].GYRO_DATA_Z1, fifo[i].GYRO_DATA_Z0);
-		}
-
-		if (!hitl_mode) {
-			_px4_gyro.set_scale(math::radians(2000.f / 32768.f));
-		}
-	}
-
-	// correct frame for publication
-	for (int i = 0; i < gyro.samples; i++) {
-		// sensor's frame is +x forward, +y left, +z up
-		//  flip y & z to publish right handed with z down (x forward, y right, z down)
-		gyro.x[i] = gyro.x[i];
-		gyro.y[i] = (gyro.y[i] == INT16_MIN) ? INT16_MAX : -gyro.y[i];
-		gyro.z[i] = (gyro.z[i] == INT16_MIN) ? INT16_MAX : -gyro.z[i];
-	}
-
-	if (!hitl_mode) {
-		_px4_gyro.set_error_count(perf_event_count(_bad_register_perf) + perf_event_count(_bad_transfer_perf) +
-					  perf_event_count(_fifo_empty_perf) + perf_event_count(_fifo_overflow_perf));
-	}
-
-	if (gyro.samples > 0) {
-		if (!hitl_mode) {
-			_px4_gyro.updateFIFO(gyro);
-		}
-	}
-}
-
-bool ICM42688P::ProcessTemperature(const FIFO::DATA fifo[], const uint8_t samples)
-{
-	int16_t temperature[FIFO_MAX_SAMPLES];
-	float temperature_sum{0};
-
-	int valid_samples = 0;
-
-	for (int i = 0; i < samples; i++) {
-		const int16_t t = combine(fifo[i].TEMP_DATA1, fifo[i].TEMP_DATA0);
-
-		// sample invalid if -32768
-		if (t != -32768) {
-			temperature_sum += t;
-			temperature[valid_samples] = t;
-			valid_samples++;
-		}
-	}
-
-	if (valid_samples > 0) {
-		const float temperature_avg = temperature_sum / valid_samples;
-
-		for (int i = 0; i < valid_samples; i++) {
-			// temperature changing wildly is an indication of a transfer error
-			if (fabsf(temperature[i] - temperature_avg) > 1000) {
-				perf_count(_bad_transfer_perf);
-				return false;
-			}
-		}
-
-		// use average temperature reading
-		const float TEMP_degC = (temperature_avg / TEMPERATURE_SENSITIVITY) + TEMPERATURE_OFFSET;
-
-		if (PX4_ISFINITE(TEMP_degC)) {
-			if (!hitl_mode) {
-				_px4_accel.set_temperature(TEMP_degC);
-				_px4_gyro.set_temperature(TEMP_degC);
-				return true;
-			}
-
-		} else {
-			perf_count(_bad_transfer_perf);
-		}
-	}
-
-	return false;
-}

boards/modalai/voxl2-slpi/src/drivers/icm42688p/ICM42688P.hpp

@@ -1,235 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (c) 2020 PX4 Development Team. All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name PX4 nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-/**
- * @file ICM42688P.hpp
- *
- * Driver for the Invensense ICM42688P connected via SPI.
- *
- */
-
-#pragma once
-
-#include "InvenSense_ICM42688P_registers.hpp"
-
-#include <drivers/drv_hrt.h>
-#include <lib/drivers/accelerometer/PX4Accelerometer.hpp>
-#include <lib/drivers/device/spi.h>
-#include <lib/drivers/gyroscope/PX4Gyroscope.hpp>
-#include <lib/geo/geo.h>
-#include <lib/perf/perf_counter.h>
-#include <px4_platform_common/atomic.h>
-#include <px4_platform_common/i2c_spi_buses.h>
-#include <uORB/topics/imu_server.h>
-#include <uORB/topics/sensor_accel_fifo.h>
-#include <uORB/topics/sensor_gyro_fifo.h>
-#include <memory>
-
-using namespace InvenSense_ICM42688P;
-
-extern bool hitl_mode;
-
-class ICM42688P : public device::SPI, public I2CSPIDriver<ICM42688P>
-{
-public:
-	// ICM42688P(I2CSPIBusOption bus_option, int bus, uint32_t device, enum Rotation rotation, int bus_frequency,
-	// 	  spi_mode_e spi_mode, spi_drdy_gpio_t drdy_gpio);
-	ICM42688P(const I2CSPIDriverConfig &config);
-	~ICM42688P() override;
-
-	// static I2CSPIDriverBase *instantiate(const BusCLIArguments &cli, const BusInstanceIterator &iterator,
-	// 				     int runtime_instance);
-	static void print_usage();
-
-	void RunImpl();
-
-	int init() override;
-	void print_status() override;
-
-private:
-	void exit_and_cleanup() override;
-
-	// Sensor Configuration
-	static constexpr float IMU_ODR{8000.f}; // 8kHz accel & gyro ODR configured
-	static constexpr float FIFO_SAMPLE_DT{1e6f / IMU_ODR};
-	static constexpr float GYRO_RATE{1e6f / FIFO_SAMPLE_DT};
-	static constexpr float ACCEL_RATE{1e6f / FIFO_SAMPLE_DT};
-
-	// maximum FIFO samples per transfer is limited to the size of sensor_accel_fifo/sensor_gyro_fifo
-	// static constexpr uint32_t FIFO_MAX_SAMPLES{math::min(math::min(FIFO::SIZE / sizeof(FIFO::DATA), sizeof(sensor_gyro_fifo_s::x) / sizeof(sensor_gyro_fifo_s::x[0])), sizeof(sensor_accel_fifo_s::x) / sizeof(sensor_accel_fifo_s::x[0]) * (int)(GYRO_RATE / ACCEL_RATE))};
-	static constexpr uint32_t FIFO_MAX_SAMPLES{10};
-
-	// Transfer data
-	struct FIFOTransferBuffer {
-		uint8_t cmd{static_cast<uint8_t>(Register::BANK_0::INT_STATUS) | DIR_READ};
-		uint8_t INT_STATUS{0};
-		uint8_t FIFO_COUNTH{0};
-		uint8_t FIFO_COUNTL{0};
-		FIFO::DATA f[FIFO_MAX_SAMPLES] {};
-	};
-	// ensure no struct padding
-	static_assert(sizeof(FIFOTransferBuffer) == (4 + FIFO_MAX_SAMPLES *sizeof(FIFO::DATA)),
-		      "Invalid FIFOTransferBuffer size");
-
-	struct register_bank0_config_t {
-		Register::BANK_0 reg;
-		uint8_t set_bits{0};
-		uint8_t clear_bits{0};
-	};
-
-	struct register_bank1_config_t {
-		Register::BANK_1 reg;
-		uint8_t set_bits{0};
-		uint8_t clear_bits{0};
-	};
-
-	struct register_bank2_config_t {
-		Register::BANK_2 reg;
-		uint8_t set_bits{0};
-		uint8_t clear_bits{0};
-	};
-
-	int probe() override;
-
-	bool Reset();
-
-	bool Configure();
-	void ConfigureSampleRate(int sample_rate);
-	void ConfigureFIFOWatermark(uint8_t samples);
-
-	void SelectRegisterBank(enum REG_BANK_SEL_BIT bank, bool force = false);
-	void SelectRegisterBank(Register::BANK_0 reg) { SelectRegisterBank(REG_BANK_SEL_BIT::USER_BANK_0); }
-	void SelectRegisterBank(Register::BANK_1 reg) { SelectRegisterBank(REG_BANK_SEL_BIT::USER_BANK_1); }
-	void SelectRegisterBank(Register::BANK_2 reg) { SelectRegisterBank(REG_BANK_SEL_BIT::USER_BANK_2); }
-
-	static int DataReadyInterruptCallback(int irq, void *context, void *arg);
-	void DataReady();
-	bool DataReadyInterruptConfigure();
-	bool DataReadyInterruptDisable();
-
-	template <typename T> bool RegisterCheck(const T &reg_cfg);
-	template <typename T> uint8_t RegisterRead(T reg);
-	template <typename T> void RegisterWrite(T reg, uint8_t value);
-	template <typename T> void RegisterSetAndClearBits(T reg, uint8_t setbits, uint8_t clearbits);
-	template <typename T> void RegisterSetBits(T reg, uint8_t setbits) { RegisterSetAndClearBits(reg, setbits, 0); }
-	template <typename T> void RegisterClearBits(T reg, uint8_t clearbits) { RegisterSetAndClearBits(reg, 0, clearbits); }
-
-	uint16_t FIFOReadCount();
-	bool FIFORead(const hrt_abstime &timestamp_sample, uint16_t samples);
-	void FIFOReset();
-
-	void ProcessIMU(const hrt_abstime &timestamp_sample, const FIFO::DATA fifo[], const uint8_t samples);
-	void ProcessAccel(const hrt_abstime &timestamp_sample, const FIFO::DATA fifo[], const uint8_t samples);
-	void ProcessGyro(const hrt_abstime &timestamp_sample, const FIFO::DATA fifo[], const uint8_t samples);
-	bool ProcessTemperature(const FIFO::DATA fifo[], const uint8_t samples);
-
-	const spi_drdy_gpio_t _drdy_gpio;
-
-	// std::shared_ptr<PX4Accelerometer> _px4_accel;
-	// std::shared_ptr<PX4Gyroscope> _px4_gyro;
-	PX4Accelerometer _px4_accel;
-	PX4Gyroscope _px4_gyro;
-
-	perf_counter_t _bad_register_perf{perf_alloc(PC_COUNT, MODULE_NAME": bad register")};
-	perf_counter_t _bad_transfer_perf{perf_alloc(PC_COUNT, MODULE_NAME": bad transfer")};
-	perf_counter_t _fifo_empty_perf{perf_alloc(PC_COUNT, MODULE_NAME": FIFO empty")};
-	perf_counter_t _fifo_overflow_perf{perf_alloc(PC_COUNT, MODULE_NAME": FIFO overflow")};
-	perf_counter_t _fifo_reset_perf{perf_alloc(PC_COUNT, MODULE_NAME": FIFO reset")};
-	perf_counter_t _drdy_missed_perf{nullptr};
-
-	hrt_abstime _reset_timestamp{0};
-	hrt_abstime _last_config_check_timestamp{0};
-	hrt_abstime _temperature_update_timestamp{0};
-	int _failure_count{0};
-
-	enum REG_BANK_SEL_BIT _last_register_bank {REG_BANK_SEL_BIT::USER_BANK_0};
-
-	px4::atomic<uint32_t> _drdy_fifo_read_samples{0};
-	bool _data_ready_interrupt_enabled{false};
-
-	enum class STATE : uint8_t {
-		RESET,
-		WAIT_FOR_RESET,
-		CONFIGURE,
-		FIFO_READ,
-	} _state{STATE::RESET};
-
-	uint16_t _fifo_empty_interval_us{1250}; // default 1250 us / 800 Hz transfer interval
-	uint32_t _fifo_gyro_samples{static_cast<uint32_t>(_fifo_empty_interval_us / (1000000 / GYRO_RATE))};
-
-	uint8_t _checked_register_bank0{0};
-	static constexpr uint8_t size_register_bank0_cfg{12};
-	register_bank0_config_t _register_bank0_cfg[size_register_bank0_cfg] {
-		// Register                              | Set bits, Clear bits
-		{ Register::BANK_0::INT_CONFIG,           INT_CONFIG_BIT::INT1_MODE | INT_CONFIG_BIT::INT1_DRIVE_CIRCUIT, INT_CONFIG_BIT::INT1_POLARITY },
-		{ Register::BANK_0::FIFO_CONFIG,          FIFO_CONFIG_BIT::FIFO_MODE_STOP_ON_FULL, 0 },
-		{ Register::BANK_0::GYRO_CONFIG0,         GYRO_CONFIG0_BIT::GYRO_FS_SEL_2000_DPS | GYRO_CONFIG0_BIT::GYRO_ODR_8KHZ_SET, GYRO_CONFIG0_BIT::GYRO_ODR_8KHZ_CLEAR },
-		{ Register::BANK_0::ACCEL_CONFIG0,        ACCEL_CONFIG0_BIT::ACCEL_FS_SEL_16G | ACCEL_CONFIG0_BIT::ACCEL_ODR_8KHZ_SET, ACCEL_CONFIG0_BIT::ACCEL_ODR_8KHZ_CLEAR },
-		{ Register::BANK_0::GYRO_CONFIG1,         0, GYRO_CONFIG1_BIT::GYRO_UI_FILT_ORD },
-		{ Register::BANK_0::GYRO_ACCEL_CONFIG0,   0, GYRO_ACCEL_CONFIG0_BIT::ACCEL_UI_FILT_BW | GYRO_ACCEL_CONFIG0_BIT::GYRO_UI_FILT_BW },
-		{ Register::BANK_0::ACCEL_CONFIG1,        0, ACCEL_CONFIG1_BIT::ACCEL_UI_FILT_ORD },
-		{ Register::BANK_0::FIFO_CONFIG1,         FIFO_CONFIG1_BIT::FIFO_WM_GT_TH | FIFO_CONFIG1_BIT::FIFO_HIRES_EN | FIFO_CONFIG1_BIT::FIFO_TEMP_EN | FIFO_CONFIG1_BIT::FIFO_GYRO_EN | FIFO_CONFIG1_BIT::FIFO_ACCEL_EN, 0 },
-		{ Register::BANK_0::FIFO_CONFIG2,         0, 0 }, // FIFO_WM[7:0] set at runtime
-		{ Register::BANK_0::FIFO_CONFIG3,         0, 0 }, // FIFO_WM[11:8] set at runtime
-		{ Register::BANK_0::INT_CONFIG0,          INT_CONFIG0_BIT::CLEAR_ON_FIFO_READ, 0 },
-		{ Register::BANK_0::INT_SOURCE0,          INT_SOURCE0_BIT::FIFO_THS_INT1_EN, 0 },
-	};
-
-	uint8_t _checked_register_bank1{0};
-	static constexpr uint8_t size_register_bank1_cfg{4};
-	register_bank1_config_t _register_bank1_cfg[size_register_bank1_cfg] {
-		// Register                              | Set bits, Clear bits
-		{ Register::BANK_1::GYRO_CONFIG_STATIC2,  0, GYRO_CONFIG_STATIC2_BIT::GYRO_NF_DIS | GYRO_CONFIG_STATIC2_BIT::GYRO_AAF_DIS },
-		{ Register::BANK_1::GYRO_CONFIG_STATIC3,  GYRO_CONFIG_STATIC3_BIT::GYRO_AAF_DELT_SET, GYRO_CONFIG_STATIC3_BIT::GYRO_AAF_DELT_CLEAR},
-		{ Register::BANK_1::GYRO_CONFIG_STATIC4,  GYRO_CONFIG_STATIC4_BIT::GYRO_AAF_DELTSQR_LOW_SET, GYRO_CONFIG_STATIC4_BIT::GYRO_AAF_DELTSQR_LOW_CLEAR},
-		{ Register::BANK_1::GYRO_CONFIG_STATIC5,  GYRO_CONFIG_STATIC5_BIT::GYRO_AAF_BITSHIFT_SET | GYRO_CONFIG_STATIC5_BIT::GYRO_AAF_DELTSQR_HIGH_SET, GYRO_CONFIG_STATIC5_BIT::GYRO_AAF_BITSHIFT_CLEAR | GYRO_CONFIG_STATIC5_BIT::GYRO_AAF_DELTSQR_HIGH_CLEAR},
-	};
-
-	uint8_t _checked_register_bank2{0};
-	static constexpr uint8_t size_register_bank2_cfg{3};
-	register_bank2_config_t _register_bank2_cfg[size_register_bank2_cfg] {
-		// Register                              | Set bits, Clear bits
-		{ Register::BANK_2::ACCEL_CONFIG_STATIC2, ACCEL_CONFIG_STATIC2_BIT::ACCEL_AAF_DELT_SET, ACCEL_CONFIG_STATIC2_BIT::ACCEL_AAF_DELT_CLEAR | ACCEL_CONFIG_STATIC2_BIT::ACCEL_AAF_DIS },
-		{ Register::BANK_2::ACCEL_CONFIG_STATIC3, ACCEL_CONFIG_STATIC3_BIT::ACCEL_AAF_DELTSQR_LOW_SET, ACCEL_CONFIG_STATIC3_BIT::ACCEL_AAF_DELTSQR_LOW_CLEAR },
-		{ Register::BANK_2::ACCEL_CONFIG_STATIC4, ACCEL_CONFIG_STATIC4_BIT::ACCEL_AAF_BITSHIFT_SET | ACCEL_CONFIG_STATIC4_BIT::ACCEL_AAF_DELTSQR_HIGH_SET, ACCEL_CONFIG_STATIC4_BIT::ACCEL_AAF_BITSHIFT_CLEAR | ACCEL_CONFIG_STATIC4_BIT::ACCEL_AAF_DELTSQR_HIGH_CLEAR },
-	};
-
-	uint32_t _temperature_samples{0};
-
-	// Support for the IMU server
-	uint32_t _imu_server_index{0};
-	uint32_t _imu_server_decimator{0};
-	imu_server_s _imu_server_data;
-	uORB::Publication<imu_server_s> _imu_server_pub{ORB_ID(imu_server)};
-
-};

boards/modalai/voxl2-slpi/src/drivers/icm42688p/InvenSense_ICM42688P_registers.hpp

@@ -1,430 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (c) 2020 PX4 Development Team. All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name PX4 nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-/**
- * @file InvenSense_ICM42688P_registers.hpp
- *
- * Invensense ICM-42688-P registers.
- *
- */
-
-#pragma once
-
-#include <cstdint>
-
-namespace InvenSense_ICM42688P
-{
-// TODO: move to a central header
-static constexpr uint8_t Bit0 = (1 << 0);
-static constexpr uint8_t Bit1 = (1 << 1);
-static constexpr uint8_t Bit2 = (1 << 2);
-static constexpr uint8_t Bit3 = (1 << 3);
-static constexpr uint8_t Bit4 = (1 << 4);
-static constexpr uint8_t Bit5 = (1 << 5);
-static constexpr uint8_t Bit6 = (1 << 6);
-static constexpr uint8_t Bit7 = (1 << 7);
-
-static constexpr uint32_t SPI_SPEED = 24 * 1000 * 1000; // 24 MHz SPI
-static constexpr uint8_t DIR_READ = 0x80;
-
-static constexpr uint8_t WHOAMI = 0x47;
-
-static constexpr float TEMPERATURE_SENSITIVITY = 132.48f; // LSB/C
-static constexpr float TEMPERATURE_OFFSET = 25.f; // C
-
-namespace Register
-{
-
-enum class BANK_0 : uint8_t {
-	DEVICE_CONFIG      = 0x11,
-
-	INT_CONFIG         = 0x14,
-
-	FIFO_CONFIG        = 0x16,
-
-	TEMP_DATA1         = 0x1D,
-	TEMP_DATA0         = 0x1E,
-
-	INT_STATUS         = 0x2D,
-	FIFO_COUNTH        = 0x2E,
-	FIFO_COUNTL        = 0x2F,
-	FIFO_DATA          = 0x30,
-
-	SIGNAL_PATH_RESET  = 0x4B,
-	INTF_CONFIG0       = 0x4C,
-	INTF_CONFIG1       = 0x4D,
-	PWR_MGMT0          = 0x4E,
-	GYRO_CONFIG0       = 0x4F,
-	ACCEL_CONFIG0      = 0x50,
-	GYRO_CONFIG1       = 0x51,
-	GYRO_ACCEL_CONFIG0 = 0x52,
-	ACCEL_CONFIG1      = 0x53,
-
-	FIFO_CONFIG1       = 0x5F,
-	FIFO_CONFIG2       = 0x60,
-	FIFO_CONFIG3       = 0x61,
-
-	INT_CONFIG0        = 0x63,
-
-	INT_SOURCE0        = 0x65,
-
-	SELF_TEST_CONFIG   = 0x70,
-
-	WHO_AM_I           = 0x75,
-	REG_BANK_SEL       = 0x76,
-};
-
-enum class BANK_1 : uint8_t {
-	GYRO_CONFIG_STATIC2 = 0x0B,
-	GYRO_CONFIG_STATIC3 = 0x0C,
-	GYRO_CONFIG_STATIC4 = 0x0D,
-	GYRO_CONFIG_STATIC5 = 0x0E,
-	INTF_CONFIG5        = 0x7B,
-};
-enum class BANK_2 : uint8_t {
-	ACCEL_CONFIG_STATIC2 = 0x03,
-	ACCEL_CONFIG_STATIC3 = 0x04,
-	ACCEL_CONFIG_STATIC4 = 0x05,
-};
-
-};
-
-//---------------- BANK0 Register bits
-
-// DEVICE_CONFIG
-enum DEVICE_CONFIG_BIT : uint8_t {
-	SOFT_RESET_CONFIG = Bit0, //
-};
-
-// INT_CONFIG
-enum INT_CONFIG_BIT : uint8_t {
-	INT1_MODE           = Bit2,
-	INT1_DRIVE_CIRCUIT  = Bit1,
-	INT1_POLARITY       = Bit0,
-};
-
-// FIFO_CONFIG
-enum FIFO_CONFIG_BIT : uint8_t {
-	// 7:6 FIFO_MODE
-	FIFO_MODE_STOP_ON_FULL = Bit7 | Bit6, // 11: STOP-on-FULL Mode
-};
-
-// INT_STATUS
-enum INT_STATUS_BIT : uint8_t {
-	RESET_DONE_INT = Bit4,
-	DATA_RDY_INT   = Bit3,
-	FIFO_THS_INT   = Bit2,
-	FIFO_FULL_INT  = Bit1,
-};
-
-// SIGNAL_PATH_RESET
-enum SIGNAL_PATH_RESET_BIT : uint8_t {
-	ABORT_AND_RESET = Bit3,
-	FIFO_FLUSH      = Bit1,
-};
-
-// PWR_MGMT0
-enum PWR_MGMT0_BIT : uint8_t {
-	GYRO_MODE_LOW_NOISE  = Bit3 | Bit2, // 11: Places gyroscope in Low Noise (LN) Mode
-	ACCEL_MODE_LOW_NOISE = Bit1 | Bit0, // 11: Places accelerometer in Low Noise (LN) Mode
-};
-
-// GYRO_CONFIG0
-enum GYRO_CONFIG0_BIT : uint8_t {
-	// 7:5 GYRO_FS_SEL
-	GYRO_FS_SEL_2000_DPS = 0, // 0b000 = ±2000dps (default)
-	GYRO_FS_SEL_1000_DPS = Bit5,
-	GYRO_FS_SEL_500_DPS  = Bit6,
-	GYRO_FS_SEL_250_DPS  = Bit6 | Bit5,
-	GYRO_FS_SEL_125_DPS  = Bit7,
-
-
-	// 3:0 GYRO_ODR
-	//  0001: 32kHz
-	GYRO_ODR_32KHZ_SET   = Bit0,
-	GYRO_ODR_32KHZ_CLEAR = Bit3 | Bit2 | Bit0,
-	//  0010: 16kHz
-	GYRO_ODR_16KHZ_SET   = Bit1,
-	GYRO_ODR_16KHZ_CLEAR = Bit3 | Bit2 | Bit0,
-	//  0011: 8kHz
-	GYRO_ODR_8KHZ_SET    = Bit1 | Bit0,
-	GYRO_ODR_8KHZ_CLEAR  = Bit3 | Bit2,
-	//  0110: 1kHz (default)
-	GYRO_ODR_1KHZ_SET    = Bit2 | Bit1,
-	GYRO_ODR_1KHZ_CLEAR  = Bit3 | Bit0,
-};
-
-// ACCEL_CONFIG0
-enum ACCEL_CONFIG0_BIT : uint8_t {
-	// 7:5 ACCEL_FS_SEL
-	ACCEL_FS_SEL_16G = 0, // 000: ±16g (default)
-	ACCEL_FS_SEL_8G  = Bit5,
-	ACCEL_FS_SEL_4G  = Bit6,
-	ACCEL_FS_SEL_2G  = Bit6 | Bit5,
-
-
-	// 3:0 ACCEL_ODR
-	//  0001: 32kHz
-	ACCEL_ODR_32KHZ_SET   = Bit0,
-	ACCEL_ODR_32KHZ_CLEAR = Bit3 | Bit2 | Bit0,
-	//  0010: 16kHz
-	ACCEL_ODR_16KHZ_SET   = Bit1,
-	ACCEL_ODR_16KHZ_CLEAR = Bit3 | Bit2 | Bit0,
-	//  0011: 8kHz
-	ACCEL_ODR_8KHZ_SET    = Bit1 | Bit0,
-	ACCEL_ODR_8KHZ_CLEAR  = Bit3 | Bit2,
-	//  0110: 1kHz (default)
-	ACCEL_ODR_1KHZ_SET    = Bit2 | Bit1,
-	ACCEL_ODR_1KHZ_CLEAR  = Bit3 | Bit0,
-};
-
-// GYRO_CONFIG1
-enum GYRO_CONFIG1_BIT : uint8_t {
-	GYRO_UI_FILT_ORD = Bit3 | Bit2, // 00: 1st Order
-};
-
-// GYRO_ACCEL_CONFIG0
-enum GYRO_ACCEL_CONFIG0_BIT : uint8_t {
-	// 7:4 ACCEL_UI_FILT_BW
-	ACCEL_UI_FILT_BW = Bit7 | Bit6 | Bit5 | Bit4, // 0: BW=ODR/2
-
-	// 3:0 GYRO_UI_FILT_BW
-	GYRO_UI_FILT_BW  = Bit3 | Bit2 | Bit1 | Bit0, // 0: BW=ODR/2
-};
-
-// ACCEL_CONFIG1
-enum ACCEL_CONFIG1_BIT : uint8_t {
-	ACCEL_UI_FILT_ORD = Bit4 | Bit3, // 00: 1st Order
-};
-
-// FIFO_CONFIG1
-enum FIFO_CONFIG1_BIT : uint8_t {
-	FIFO_RESUME_PARTIAL_RD = Bit6,
-	FIFO_WM_GT_TH          = Bit5,
-	FIFO_HIRES_EN          = Bit4,
-	FIFO_TEMP_EN           = Bit2,
-	FIFO_GYRO_EN           = Bit1,
-	FIFO_ACCEL_EN          = Bit0,
-};
-
-// INT_CONFIG0
-enum INT_CONFIG0_BIT : uint8_t {
-	// 3:2 FIFO_THS_INT_CLEAR
-	CLEAR_ON_FIFO_READ = Bit3,
-};
-
-// INT_SOURCE0
-enum INT_SOURCE0_BIT : uint8_t {
-	UI_FSYNC_INT1_EN   = Bit6,
-	PLL_RDY_INT1_EN    = Bit5,
-	RESET_DONE_INT1_EN = Bit4,
-	UI_DRDY_INT1_EN    = Bit3,
-	FIFO_THS_INT1_EN   = Bit2, // FIFO threshold interrupt routed to INT1
-	FIFO_FULL_INT1_EN  = Bit1,
-	UI_AGC_RDY_INT1_EN = Bit0,
-};
-
-// REG_BANK_SEL
-enum REG_BANK_SEL_BIT : uint8_t {
-	USER_BANK_0 = 0,           // 0: Select USER BANK 0.
-	USER_BANK_1 = Bit0,        // 1: Select USER BANK 1.
-	USER_BANK_2 = Bit1,        // 2: Select USER BANK 2.
-	USER_BANK_3 = Bit1 | Bit0, // 3: Select USER BANK 3.
-};
-
-
-//---------------- BANK1 Register bits
-
-// GYRO_CONFIG_STATIC2
-enum GYRO_CONFIG_STATIC2_BIT : uint8_t {
-	GYRO_AAF_DIS = Bit1,
-	GYRO_NF_DIS  = Bit0,
-};
-
-// GYRO_CONFIG_STATIC3
-enum GYRO_CONFIG_STATIC3_BIT : uint8_t {
-
-	// 585 Hz
-	GYRO_AAF_DELT_SET = Bit3 | Bit2 | Bit0, //13
-	GYRO_AAF_DELT_CLEAR = Bit5 | Bit4 | Bit1,
-
-	// 213 Hz
-	// GYRO_AAF_DELT_SET = Bit2 | Bit0, //5
-	// GYRO_AAF_DELT_CLEAR = Bit5 | Bit4 | Bit3 | Bit1,
-
-	// 126 Hz
-	//GYRO_AAF_DELT_SET = Bit1 | Bit0, //3
-	//GYRO_AAF_DELT_CLEAR = Bit5 | Bit4 | Bit3 | Bit2,
-
-	// 42 Hz
-	// GYRO_AAF_DELT_SET = Bit0, //1
-	// GYRO_AAF_DELT_CLEAR = Bit5 | Bit4 | Bit3 | Bit2 | Bit1,
-
-};
-
-// GYRO_CONFIG_STATIC4
-enum GYRO_CONFIG_STATIC4_BIT : uint8_t {
-
-	// 585 Hz
-	GYRO_AAF_DELTSQR_LOW_SET = Bit7 | Bit5 | Bit3 | Bit1, //170
-	GYRO_AAF_DELTSQR_LOW_CLEAR = Bit6 | Bit4 | Bit2 | Bit0,
-
-	// 213 Hz
-	// GYRO_AAF_DELTSQR_LOW_SET = Bit4 | Bit3 | Bit0, //25
-	// GYRO_AAF_DELTSQR_LOW_CLEAR = Bit7 | Bit6 | Bit5 | Bit2 | Bit1,
-
-	// 126 Hz
-	//GYRO_AAF_DELTSQR_LOW_SET = Bit3 | Bit0, //9
-	//GYRO_AAF_DELTSQR_LOW_CLEAR = Bit7 | Bit6 | Bit5 | Bit4 | Bit2 | Bit1,
-
-	// 42 Hz
-	// GYRO_AAF_DELTSQR_LOW_SET = Bit0, //1
-	// GYRO_AAF_DELTSQR_LOW_CLEAR = Bit7 | Bit6 | Bit5 | Bit4 | Bit3 | Bit2 | Bit1,
-};
-
-// GYRO_CONFIG_STATIC5
-enum GYRO_CONFIG_STATIC5_BIT : uint8_t {
-
-	// 585 Hz
-	GYRO_AAF_DELTSQR_HIGH_SET = 0,
-	GYRO_AAF_DELTSQR_HIGH_CLEAR = Bit3 | Bit2 | Bit1 | Bit0,
-	GYRO_AAF_BITSHIFT_SET = Bit7, // 8 << 4
-	GYRO_AAF_BITSHIFT_CLEAR = Bit6 | Bit5 | Bit4,
-
-	// 213 Hz
-	// GYRO_AAF_DELTSQR_HIGH_SET = 0,
-	// GYRO_AAF_DELTSQR_HIGH_CLEAR = Bit3 | Bit2 | Bit1 | Bit0,
-	// GYRO_AAF_BITSHIFT_SET = Bit7 | Bit5, //10
-	// GYRO_AAF_BITSHIFT_CLEAR = Bit6 | Bit4,
-
-	// 126 Hz
-	// GYRO_AAF_BITSHIFT_SET = Bit7 | Bit6, //12
-	// GYRO_AAF_BITSHIFT_CLEAR = Bit5 | Bit4,
-
-	// 42 Hz
-	// GYRO_AAF_BITSHIFT_SET = Bit7 | Bit6 | Bit5 | Bit4, //15
-	// GYRO_AAF_BITSHIFT_CLEAR = 0,
-
-
-};
-
-
-//---------------- BANK2 Register bits
-
-// ACCEL_CONFIG_STATIC2
-enum ACCEL_CONFIG_STATIC2_BIT : uint8_t {
-	ACCEL_AAF_DIS  = Bit0,
-	ACCEL_AAF_DELT = Bit3 | Bit1,
-
-	// 213 Hz
-	ACCEL_AAF_DELT_SET = Bit3 | Bit1, //5
-	ACCEL_AAF_DELT_CLEAR = Bit6 | Bit5 | Bit4 | Bit2,
-
-	// 42 Hz
-	// ACCEL_AAF_DELT_SET = Bit1, //1
-	// ACCEL_AAF_DELT_CLEAR = Bit6 | Bit5 | Bit4 | Bit3 | Bit2,
-};
-
-// ACCEL_CONFIG_STATIC3
-enum ACCEL_CONFIG_STATIC3_BIT : uint8_t {
-	ACCEL_AAF_DELTSQR_LOW = Bit4 | Bit3 | Bit0,
-	// 213 Hz
-	ACCEL_AAF_DELTSQR_LOW_SET = Bit4 | Bit3 | Bit0, //25
-	ACCEL_AAF_DELTSQR_LOW_CLEAR = Bit7 | Bit6 | Bit5 | Bit2 | Bit1,
-
-	// 42 Hz
-	// ACCEL_AAF_DELTSQR_LOW_SET = Bit0, //1
-	// ACCEL_AAF_DELTSQR_LOW_CLEAR = Bit7 | Bit6 | Bit5 | Bit4 | Bit3 | Bit2 | Bit1,
-
-};
-
-// ACCEL_CONFIG_STATIC4
-enum ACCEL_CONFIG_STATIC4_BIT : uint8_t {
-	ACCEL_AAF_BITSHIFT     = Bit7 | Bit5,
-	ACCEL_AAF_DELTSQR_HIGH = 0,
-	// 213 Hz
-	ACCEL_AAF_BITSHIFT_SET = Bit7 | Bit5, //10
-	ACCEL_AAF_BITSHIFT_CLEAR = Bit6 | Bit4,
-
-	// 42 Hz
-	// ACCEL_AAF_BITSHIFT_SET = Bit7 | Bit6 | Bit5 | Bit4, //15
-	// ACCEL_AAF_BITSHIFT_CLEAR = 0,
-
-	ACCEL_AAF_DELTSQR_HIGH_SET = 0,
-	ACCEL_AAF_DELTSQR_HIGH_CLEAR = Bit3 | Bit2 | Bit1 | Bit0,
-};
-
-
-namespace FIFO
-{
-static constexpr size_t SIZE = 2048;
-
-// FIFO_DATA layout when FIFO_CONFIG1 has FIFO_GYRO_EN and FIFO_ACCEL_EN set
-
-// Packet 4
-struct DATA {
-	uint8_t FIFO_Header;
-	uint8_t ACCEL_DATA_X1; // Accel X [19:12]
-	uint8_t ACCEL_DATA_X0; // Accel X [11:4]
-	uint8_t ACCEL_DATA_Y1; // Accel Y [19:12]
-	uint8_t ACCEL_DATA_Y0; // Accel Y [11:4]
-	uint8_t ACCEL_DATA_Z1; // Accel Z [19:12]
-	uint8_t ACCEL_DATA_Z0; // Accel Z [11:4]
-	uint8_t GYRO_DATA_X1;  // Gyro X [19:12]
-	uint8_t GYRO_DATA_X0;  // Gyro X [11:4]
-	uint8_t GYRO_DATA_Y1;  // Gyro Y [19:12]
-	uint8_t GYRO_DATA_Y0;  // Gyro Y [11:4]
-	uint8_t GYRO_DATA_Z1;  // Gyro Z [19:12]
-	uint8_t GYRO_DATA_Z0;  // Gyro Z [11:4]
-	uint8_t TEMP_DATA1;    // Temperature[15:8]
-	uint8_t TEMP_DATA0;    // Temperature[7:0]
-	uint8_t TimeStamp_h;   // TimeStamp[15:8]
-	uint8_t TimeStamp_l;   // TimeStamp[7:0]
-	uint8_t Ext_Accel_X_Gyro_X; // Accel X [3:0] Gyro X [3:0]
-	uint8_t Ext_Accel_Y_Gyro_Y; // Accel Y [3:0] Gyro Y [3:0]
-	uint8_t Ext_Accel_Z_Gyro_Z; // Accel Z [3:0] Gyro Z [3:0]
-};
-
-// With FIFO_ACCEL_EN and FIFO_GYRO_EN header should be 8’b_0110_10xx
-enum FIFO_HEADER_BIT : uint8_t {
-	HEADER_MSG             = Bit7, // 1: FIFO is empty
-	HEADER_ACCEL           = Bit6, // 1: Packet is sized so that accel data have location in the packet, FIFO_ACCEL_EN must be 1
-	HEADER_GYRO            = Bit5, // 1: Packet is sized so that gyro data have location in the packet, FIFO_GYRO_EN must be1
-	HEADER_20              = Bit4, // 1: Packet has a new and valid sample of extended 20-bit data for gyro and/or accel
-	HEADER_TIMESTAMP_FSYNC = Bit3 | Bit2,
-	HEADER_ODR_ACCEL       = Bit1, // 1: The ODR for accel is different for this accel data packet compared to the previous accel packet
-	HEADER_ODR_GYRO        = Bit0, // 1: The ODR for gyro is different for this gyro data packet compared to the previous gyro packet
-};
-
-}
-} // namespace InvenSense_ICM42688P

boards/modalai/voxl2-slpi/src/drivers/icm42688p/icm42688p_main.cpp

@@ -1,116 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (c) 2020 PX4 Development Team. All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name PX4 nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-#include "ICM42688P.hpp"
-
-#include <px4_platform_common/getopt.h>
-#include <px4_platform_common/module.h>
-#include <string>
-
-void ICM42688P::print_usage()
-{
-	PRINT_MODULE_USAGE_NAME("icm42688p", "driver");
-	PRINT_MODULE_USAGE_SUBCATEGORY("imu");
-	PRINT_MODULE_USAGE_COMMAND("start");
-	PRINT_MODULE_USAGE_PARAMS_I2C_SPI_DRIVER(false, true);
-	PRINT_MODULE_USAGE_PARAM_INT('R', 0, 0, 35, "Rotation", true);
-	PRINT_MODULE_USAGE_DEFAULT_COMMANDS();
-}
-
-// I2CSPIDriverBase *ICM42688P::instantiate(const BusCLIArguments &cli, const BusInstanceIterator &iterator,
-// 		int runtime_instance)
-// {
-// 	ICM42688P *instance = new ICM42688P(iterator.configuredBusOption(), iterator.bus(), iterator.devid(), cli.rotation,
-// 					    cli.bus_frequency, cli.spi_mode, iterator.DRDYGPIO());
-//
-// 	if (!instance) {
-// 		PX4_ERR("alloc failed");
-// 		return nullptr;
-// 	}
-//
-// 	if (OK != instance->init()) {
-// 		delete instance;
-// 		return nullptr;
-// 	}
-//
-// 	return instance;
-// }
-
-extern "C" int icm42688p_main(int argc, char *argv[])
-{
-
-	for (int i = 0; i <= argc - 1; i++) {
-		if (std::string(argv[i]) == "-h") {
-			argv[i] = 0;
-			hitl_mode = true;
-			break;
-		}
-	}
-
-	int ch;
-	using ThisDriver = ICM42688P;
-	BusCLIArguments cli{false, true};
-	cli.default_spi_frequency = SPI_SPEED;
-
-	while ((ch = cli.getOpt(argc, argv, "R:")) != EOF) {
-		switch (ch) {
-		case 'R':
-			cli.rotation = (enum Rotation)atoi(cli.optArg());
-			break;
-		}
-	}
-
-	const char *verb = cli.optArg();
-
-	if (!verb) {
-		ThisDriver::print_usage();
-		return -1;
-	}
-
-	BusInstanceIterator iterator(MODULE_NAME, cli, DRV_IMU_DEVTYPE_ICM42688P);
-
-	if (!strcmp(verb, "start")) {
-		return ThisDriver::module_start(cli, iterator);
-	}
-
-	if (!strcmp(verb, "stop")) {
-		return ThisDriver::module_stop(iterator);
-	}
-
-	if (!strcmp(verb, "status")) {
-		return ThisDriver::module_status(iterator);
-	}
-
-	ThisDriver::print_usage();
-	return -1;
-}

boards/px4/fmu-v5/rover.px4board

@@ -18,4 +18,4 @@ CONFIG_MODULES_UUV_POS_CONTROL=n
 CONFIG_MODULES_VTOL_ATT_CONTROL=n
 CONFIG_EKF2_AUX_GLOBAL_POSITION=y
 # CONFIG_EKF2_WIND is not set
-CONFIG_MODULES_DIFFERENTIAL_DRIVE_CONTROL=y
+CONFIG_MODULES_DIFFERENTIAL_DRIVE=y

boards/px4/fmu-v5x/default.px4board

@@ -53,7 +53,7 @@ CONFIG_MODULES_CAMERA_FEEDBACK=y
 CONFIG_MODULES_COMMANDER=y
 CONFIG_MODULES_CONTROL_ALLOCATOR=y
 CONFIG_MODULES_DATAMAN=y
-CONFIG_MODULES_DIFFERENTIAL_DRIVE_CONTROL=y
+CONFIG_MODULES_DIFFERENTIAL_DRIVE=y
 CONFIG_MODULES_EKF2=y
 CONFIG_MODULES_ESC_BATTERY=y
 CONFIG_MODULES_EVENTS=y

boards/px4/fmu-v5x/init/rc.board_defaults

@@ -16,7 +16,7 @@ param set-default SENS_EN_INA238 0
 param set-default SENS_EN_INA228 0
 param set-default SENS_EN_INA226 1
 
-if ver hwbasecmp 008 009 00a 010
+if ver hwbasecmp 008 009 00a 010 011
 then
 	# Skynode: use the "custom participant" config for uxrce_dds_client
 	param set-default UXRCE_DDS_PTCFG 2

boards/px4/fmu-v5x/init/rc.board_mavlink

@@ -3,7 +3,7 @@
 # board specific MAVLink startup script.
 #------------------------------------------------------------------------------
 
-if ver hwbasecmp 008 009 00a 010
+if ver hwbasecmp 008 009 00a 010 011
 then
 	# Start MAVLink on the UART connected to the mission computer
 	mavlink start -d /dev/ttyS4 -b 3000000 -r 290000 -m onboard_low_bandwidth -x -z

boards/px4/fmu-v5x/init/rc.board_sensors

@@ -49,7 +49,7 @@ then
 	fi
 fi
 
-if ver hwbasecmp 008 009 00a 010
+if ver hwbasecmp 008 009 00a 010 011
 then
 	#SKYNODE base fmu board orientation
 

boards/px4/fmu-v5x/rover.px4board

@@ -1,21 +1,16 @@
 CONFIG_DRIVERS_IRLOCK=n
 CONFIG_MODULES_AIRSPEED_SELECTOR=n
-CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=n
 CONFIG_MODULES_FLIGHT_MODE_MANAGER=n
 CONFIG_MODULES_FW_ATT_CONTROL=n
 CONFIG_MODULES_FW_AUTOTUNE_ATTITUDE_CONTROL=n
 CONFIG_MODULES_FW_POS_CONTROL=n
 CONFIG_MODULES_FW_RATE_CONTROL=n
 CONFIG_MODULES_LANDING_TARGET_ESTIMATOR=n
-CONFIG_MODULES_LOCAL_POSITION_ESTIMATOR=n
 CONFIG_MODULES_MC_ATT_CONTROL=n
 CONFIG_MODULES_MC_AUTOTUNE_ATTITUDE_CONTROL=n
 CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=n
 CONFIG_MODULES_MC_POS_CONTROL=n
 CONFIG_MODULES_MC_RATE_CONTROL=n
-CONFIG_MODULES_UUV_ATT_CONTROL=n
-CONFIG_MODULES_UUV_POS_CONTROL=n
 CONFIG_MODULES_VTOL_ATT_CONTROL=n
 CONFIG_EKF2_AUX_GLOBAL_POSITION=y
 # CONFIG_EKF2_WIND is not set
-CONFIG_MODULES_DIFFERENTIAL_DRIVE_CONTROL=y

boards/px4/fmu-v6c/rover.px4board

@@ -1,21 +1,16 @@
-CONFIG_DRIVERS_IRLOCK=n
 CONFIG_MODULES_AIRSPEED_SELECTOR=n
-CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=n
 CONFIG_MODULES_FLIGHT_MODE_MANAGER=n
 CONFIG_MODULES_FW_ATT_CONTROL=n
 CONFIG_MODULES_FW_AUTOTUNE_ATTITUDE_CONTROL=n
 CONFIG_MODULES_FW_POS_CONTROL=n
 CONFIG_MODULES_FW_RATE_CONTROL=n
 CONFIG_MODULES_LANDING_TARGET_ESTIMATOR=n
-CONFIG_MODULES_LOCAL_POSITION_ESTIMATOR=n
 CONFIG_MODULES_MC_ATT_CONTROL=n
 CONFIG_MODULES_MC_AUTOTUNE_ATTITUDE_CONTROL=n
 CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=n
 CONFIG_MODULES_MC_POS_CONTROL=n
 CONFIG_MODULES_MC_RATE_CONTROL=n
-CONFIG_MODULES_UUV_ATT_CONTROL=n
-CONFIG_MODULES_UUV_POS_CONTROL=n
 CONFIG_MODULES_VTOL_ATT_CONTROL=n
 CONFIG_EKF2_AUX_GLOBAL_POSITION=y
 # CONFIG_EKF2_WIND is not set
-CONFIG_MODULES_DIFFERENTIAL_DRIVE_CONTROL=y
+CONFIG_MODULES_DIFFERENTIAL_DRIVE=y

boards/px4/fmu-v6u/rover.px4board

@@ -13,4 +13,4 @@ CONFIG_MODULES_MC_RATE_CONTROL=n
 CONFIG_MODULES_VTOL_ATT_CONTROL=n
 CONFIG_EKF2_AUX_GLOBAL_POSITION=y
 # CONFIG_EKF2_WIND is not set
-CONFIG_MODULES_DIFFERENTIAL_DRIVE_CONTROL=y
+CONFIG_MODULES_DIFFERENTIAL_DRIVE=y

boards/px4/fmu-v6x/init/rc.board_defaults

@@ -18,7 +18,7 @@ param set-default SENS_EN_INA238 0
 param set-default SENS_EN_INA228 0
 param set-default SENS_EN_INA226 0
 
-if ver hwbasecmp 009 010
+if ver hwbasecmp 009 010 011
 then
 	# Skynode: use the "custom participant" config for uxrce_dds_client
 	param set-default UXRCE_DDS_PTCFG 2

boards/px4/fmu-v6x/init/rc.board_mavlink

@@ -4,7 +4,7 @@
 #------------------------------------------------------------------------------
 
 # if skynode base board is detected start Mavlink on Telem2
-if ver hwbasecmp 009 010
+if ver hwbasecmp 009 010 011
 then
 	mavlink start -d /dev/ttyS4 -b 3000000 -r 290000 -m onboard_low_bandwidth -x -z
 

boards/px4/fmu-v6x/init/rc.board_sensors

@@ -12,6 +12,7 @@ fi
 if param compare -s ADC_ADS1115_EN 1
 then
 	ads1115 start -X
+	board_adc start -n
 else
 	board_adc start
 fi
@@ -55,7 +56,7 @@ then
 fi
 
 #Start Auterion Power Module selector for Skynode boards
-if ver hwbasecmp 009 010
+if ver hwbasecmp 009 010 011
 then
 	pm_selector_auterion start
 else
@@ -92,7 +93,7 @@ else
 		icm20649 -s -R 6 start
 	else
 		# Internal SPI BMI088
-		if ver hwbasecmp 009 010
+		if ver hwbasecmp 009 010 011
 		then
 			bmi088 -A -R 6 -s start
 			bmi088 -G -R 6 -s start
@@ -109,7 +110,7 @@ else
 	fi
 
 	# Internal SPI bus ICM42688p
-	if ver hwbasecmp 009 010
+	if ver hwbasecmp 009 010 011
 	then
 		icm42688p -R 12 -s start
 	else
@@ -126,7 +127,7 @@ else
 		# Internal SPI bus ICM-42670-P (hard-mounted)
 		icm42670p -R 10 -s start
 	else
-		if ver hwbasecmp 009 010
+		if ver hwbasecmp 009 010 011
 		then
 			icm20602 -R 6 -s start
 		else

boards/px4/fmu-v6x/rover.px4board

@@ -13,4 +13,4 @@ CONFIG_MODULES_MC_RATE_CONTROL=n
 CONFIG_MODULES_VTOL_ATT_CONTROL=n
 CONFIG_EKF2_AUX_GLOBAL_POSITION=y
 # CONFIG_EKF2_WIND is not set
-CONFIG_MODULES_DIFFERENTIAL_DRIVE_CONTROL=y
+CONFIG_MODULES_DIFFERENTIAL_DRIVE=y

boards/px4/fmu-v6xrt/default.px4board

@@ -6,21 +6,30 @@ CONFIG_BOARD_SERIAL_GPS2="/dev/ttyS3"
 CONFIG_BOARD_SERIAL_TEL1="/dev/ttyS2"
 CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS5"
 CONFIG_BOARD_SERIAL_TEL3="/dev/ttyS6"
+CONFIG_DRIVERS_ADC_ADS1115=y
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_BMP388=y
+CONFIG_DRIVERS_BAROMETER_INVENSENSE_ICP201XX=y
 CONFIG_DRIVERS_BAROMETER_MS5611=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_DISTANCE_SENSOR_LIGHTWARE_LASER_I2C=y
+CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
+CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y
+CONFIG_DRIVERS_IMU_ANALOG_DEVICES_ADIS16470=y
 CONFIG_DRIVERS_IMU_BOSCH_BMI088=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=y
+CONFIG_DRIVERS_IMU_INVENSENSE_ICM20649=y
+CONFIG_DRIVERS_IMU_INVENSENSE_ICM20948=y
+CONFIG_DRIVERS_IMU_INVENSENSE_ICM42670P=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM42688P=y
+CONFIG_DRIVERS_IMU_INVENSENSE_ICM45686=y
+CONFIG_DRIVERS_IMU_INVENSENSE_IIM42652=y
+CONFIG_COMMON_INS=y
 CONFIG_COMMON_LIGHT=y
-CONFIG_DRIVERS_MAGNETOMETER_BOSCH_BMM150=y
-CONFIG_DRIVERS_MAGNETOMETER_HMC5883=y
-CONFIG_DRIVERS_MAGNETOMETER_ISENTEK_IST8310=y
+CONFIG_COMMON_MAGNETOMETER=y
+CONFIG_DRIVERS_OSD_MSP_OSD=y
 CONFIG_DRIVERS_POWER_MONITOR_INA226=y
 CONFIG_DRIVERS_POWER_MONITOR_INA228=y
 CONFIG_DRIVERS_POWER_MONITOR_INA238=y
@@ -32,14 +41,20 @@ CONFIG_COMMON_TELEMETRY=y
 CONFIG_DRIVERS_TONE_ALARM=y
 CONFIG_DRIVERS_UAVCAN=y
 CONFIG_COMMON_UWB=y
+CONFIG_MODULES_AIRSPEED_SELECTOR=y
 CONFIG_MODULES_BATTERY_STATUS=y
 CONFIG_MODULES_CAMERA_FEEDBACK=y
 CONFIG_MODULES_COMMANDER=y
 CONFIG_MODULES_CONTROL_ALLOCATOR=y
 CONFIG_MODULES_DATAMAN=y
 CONFIG_MODULES_EKF2=y
+CONFIG_MODULES_ESC_BATTERY=y
 CONFIG_MODULES_EVENTS=y
 CONFIG_MODULES_FLIGHT_MODE_MANAGER=y
+CONFIG_MODULES_FW_ATT_CONTROL=y
+CONFIG_MODULES_FW_AUTOTUNE_ATTITUDE_CONTROL=y
+CONFIG_MODULES_FW_POS_CONTROL=y
+CONFIG_MODULES_FW_RATE_CONTROL=y
 CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_GYRO_CALIBRATION=y
 CONFIG_MODULES_GYRO_FFT=y
@@ -57,11 +72,15 @@ CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=y
 CONFIG_MODULES_MC_POS_CONTROL=y
 CONFIG_MODULES_MC_RATE_CONTROL=y
 CONFIG_MODULES_NAVIGATOR=y
+CONFIG_MODE_NAVIGATOR_VTOL_TAKEOFF=y
 CONFIG_MODULES_RC_UPDATE=y
 CONFIG_MODULES_ROVER_POS_CONTROL=y
 CONFIG_MODULES_SENSORS=y
 CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
+CONFIG_MODULES_UXRCE_DDS_CLIENT=y
+CONFIG_MODULES_VTOL_ATT_CONTROL=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
+CONFIG_SYSTEMCMDS_BSONDUMP=y
 CONFIG_SYSTEMCMDS_DMESG=y
 CONFIG_SYSTEMCMDS_DUMPFILE=y
 CONFIG_SYSTEMCMDS_HARDFAULT_LOG=y

boards/px4/fmu-v6xrt/init/rc.board_mavlink

@@ -4,7 +4,7 @@
 #------------------------------------------------------------------------------
 
 # if skynode base board is detected start Mavlink on Telem2
-if ver hwbasecmp 009 010
+if ver hwbasecmp 009 010 011
 then
 	mavlink start -d /dev/ttyS5 -b 3000000 -r 290000 -m onboard_low_bandwidth -x -z
 

boards/px4/fmu-v6xrt/nuttx-config/nsh/defconfig

@@ -257,7 +257,7 @@ CONFIG_SCHED_INSTRUMENTATION_EXTERNAL=y
 CONFIG_SCHED_INSTRUMENTATION_SWITCH=y
 CONFIG_SCHED_LPWORK=y
 CONFIG_SCHED_LPWORKPRIORITY=50
-CONFIG_SCHED_LPWORKSTACKSIZE=1632
+CONFIG_SCHED_LPWORKSTACKSIZE=2032
 CONFIG_SCHED_WAITPID=y
 CONFIG_SDIO_BLOCKSETUP=y
 CONFIG_SEM_PREALLOCHOLDERS=32

boards/px4/fmu-v6xrt/rover.px4board

@@ -1,4 +1,9 @@
+CONFIG_MODULES_AIRSPEED_SELECTOR=n
 CONFIG_MODULES_FLIGHT_MODE_MANAGER=n
+CONFIG_MODULES_FW_ATT_CONTROL=n
+CONFIG_MODULES_FW_AUTOTUNE_ATTITUDE_CONTROL=n
+CONFIG_MODULES_FW_POS_CONTROL=n
+CONFIG_MODULES_FW_RATE_CONTROL=n
 CONFIG_MODULES_LANDING_TARGET_ESTIMATOR=n
 CONFIG_MODULES_LOCAL_POSITION_ESTIMATOR=n
 CONFIG_MODULES_MC_ATT_CONTROL=n
@@ -6,6 +11,7 @@ CONFIG_MODULES_MC_AUTOTUNE_ATTITUDE_CONTROL=n
 CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=n
 CONFIG_MODULES_MC_POS_CONTROL=n
 CONFIG_MODULES_MC_RATE_CONTROL=n
+CONFIG_MODULES_VTOL_ATT_CONTROL=n
 CONFIG_EKF2_AUX_GLOBAL_POSITION=y
 # CONFIG_EKF2_WIND is not set
-CONFIG_MODULES_DIFFERENTIAL_DRIVE_CONTROL=y
+CONFIG_MODULES_DIFFERENTIAL_DRIVE=y

boards/px4/sitl/default.px4board

@@ -12,7 +12,7 @@ CONFIG_MODULES_CAMERA_FEEDBACK=y
 CONFIG_MODULES_COMMANDER=y
 CONFIG_MODULES_CONTROL_ALLOCATOR=y
 CONFIG_MODULES_DATAMAN=y
-CONFIG_MODULES_DIFFERENTIAL_DRIVE_CONTROL=y
+CONFIG_MODULES_DIFFERENTIAL_DRIVE=y
 CONFIG_MODULES_EKF2=y
 CONFIG_EKF2_VERBOSE_STATUS=y
 CONFIG_EKF2_AUX_GLOBAL_POSITION=y

msg/CMakeLists.txt

@@ -173,6 +173,7 @@ set(msg_files
 	RegisterExtComponentReply.msg
 	RegisterExtComponentRequest.msg
 	Rpm.msg
+	RtlStatus.msg
 	RtlTimeEstimate.msg
 	SatelliteInfo.msg
 	SensorAccel.msg

msg/DifferentialDriveSetpoint.msg

@@ -1,4 +1,8 @@
 uint64 timestamp # time since system start (microseconds)
 
 float32 speed # [m/s] collective roll-off speed in body x-axis
+bool closed_loop_speed_control # true if speed is controlled using estimator feedback, false if direct feed-forward
 float32 yaw_rate # [rad/s] yaw rate
+bool closed_loop_yaw_rate_control # true if yaw rate is controlled using gyroscope feedback, false if direct feed-forward
+
+# TOPICS differential_drive_setpoint differential_drive_control_output

msg/EstimatorStatusFlags.msg

@@ -55,15 +55,9 @@ bool fs_bad_airspeed          #  5 - true if fusion of the airspeed has encounte
 bool fs_bad_sideslip          #  6 - true if fusion of the synthetic sideslip constraint has encountered a numerical error
 bool fs_bad_optflow_x         #  7 - true if fusion of the optical flow X axis has encountered a numerical error
 bool fs_bad_optflow_y         #  8 - true if fusion of the optical flow Y axis has encountered a numerical error
-bool fs_bad_vel_n             #  9 - true if fusion of the North velocity has encountered a numerical error
-bool fs_bad_vel_e             # 10 - true if fusion of the East velocity has encountered a numerical error
-bool fs_bad_vel_d             # 11 - true if fusion of the Down velocity has encountered a numerical error
-bool fs_bad_pos_n             # 12 - true if fusion of the North position has encountered a numerical error
-bool fs_bad_pos_e             # 13 - true if fusion of the East position has encountered a numerical error
-bool fs_bad_pos_d             # 14 - true if fusion of the Down position has encountered a numerical error
-bool fs_bad_acc_bias          # 15 - true if bad delta velocity bias estimates have been detected
-bool fs_bad_acc_vertical      # 16 - true if bad vertical accelerometer data has been detected
-bool fs_bad_acc_clipping      # 17 - true if delta velocity data contains clipping (asymmetric railing)
+bool fs_bad_acc_bias          #  9 - true if bad delta velocity bias estimates have been detected
+bool fs_bad_acc_vertical      # 10 - true if bad vertical accelerometer data has been detected
+bool fs_bad_acc_clipping      # 11 - true if delta velocity data contains clipping (asymmetric railing)
 
 
 # innovation test failures

msg/OrbTestMedium.msg

@@ -4,4 +4,6 @@ int32 val
 
 uint8[64] junk
 
+uint8 ORB_QUEUE_LENGTH = 16
+
 # TOPICS orb_test_medium orb_test_medium_multi orb_test_medium_wrap_around orb_test_medium_queue orb_test_medium_queue_poll

msg/RtlStatus.msg

@@ -0,0 +1,15 @@
+uint64 timestamp                      # time since system start (microseconds)
+
+uint32 safe_points_id 		      # unique ID of active set of safe_point_items
+bool is_evaluation_pending 	      # flag if the RTL point needs reevaluation (e.g. new safe points available, but need loading).
+
+bool has_vtol_approach 		      # flag if approaches are defined for current RTL_TYPE parameter setting
+
+uint8 rtl_type	      		      # Type of RTL chosen
+uint8 safe_point_index 		      # index of the chosen safe point, if in RTL_STATUS_TYPE_DIRECT_SAFE_POINT mode
+
+uint8 RTL_STATUS_TYPE_NONE=0       # RTL type is pending if evaluation can't pe performed currently e.g. when it is still loading the safe points
+uint8 RTL_STATUS_TYPE_DIRECT_SAFE_POINT=1 # RTL type is chosen to directly go to a safe point or home position
+uint8 RTL_STATUS_TYPE_DIRECT_MISSION_LAND=2 # RTL type is going straight to the beginning of the mission landing
+uint8 RTL_STATUS_TYPE_FOLLOW_MISSION=3 	# RTL type is following the mission from closest point to mission landing
+uint8 RTL_STATUS_TYPE_FOLLOW_MISSION_REVERSE=4 # RTL type is following the mission in reverse to the start position

platforms/common/pab_manifest.c

@@ -48,6 +48,8 @@
 
 #include <board_config.h>
 
+#if defined(BOARD_HAS_HW_SPLIT_VERSIONING)
+
 #include <inttypes.h>
 #include <stdbool.h>
 #include <syslog.h>
@@ -57,7 +59,6 @@
 /****************************************************************************
  * Pre-Processor Definitions
  ****************************************************************************/
-#if defined(BOARD_HAS_HW_SPLIT_VERSIONING)
 
 typedef struct {
 	hw_base_id_t             hw_base_id; /* The ID of the Base */
@@ -292,12 +293,6 @@ static const px4_hw_mft_item_t base_configuration_9[] = {
 		.mandatory   = 1,
 		.connection  = px4_hw_con_onboard,
 	},
-	{
-		.id          =  PX4_MFT_PM2,
-		.present     = 1,
-		.mandatory   = 1,
-		.connection  = px4_hw_con_onboard,
-	},
 	{
 		.id          = PX4_MFT_ETHERNET,
 		.present     = 1,
@@ -315,6 +310,52 @@ static const px4_hw_mft_item_t base_configuration_9[] = {
 // BASE ID 10  Skynode QS no USB Alaised to ID 9
 // BASE ID 16  Auterion Skynode RC10, RC11, RC12, RC13 Alaised to ID 0
 
+// BASE ID 17  Auterion Skynode RC13 with many parts removed
+static const px4_hw_mft_item_t base_configuration_17[] = {
+	{
+		.id          = PX4_MFT_PX4IO,
+		.present     = 0,
+		.mandatory   = 0,
+		.connection  = px4_hw_con_onboard,
+	},
+	{
+		.id          = PX4_MFT_USB,
+		.present     = 1,
+		.mandatory   = 1,
+		.connection  = px4_hw_con_unknown,
+	},
+	{
+		.id          = PX4_MFT_CAN2,
+		.present     = 0,
+		.mandatory   = 0,
+		.connection  = px4_hw_con_onboard,
+	},
+	{
+		.id          = PX4_MFT_CAN3,
+		.present     = 0,
+		.mandatory   = 0,
+		.connection  = px4_hw_con_unknown,
+	},
+	{
+		.id          = PX4_MFT_PM2,
+		.present     = 0,
+		.mandatory   = 0,
+		.connection  = px4_hw_con_onboard,
+	},
+	{
+		.id          = PX4_MFT_ETHERNET,
+		.present     = 1,
+		.mandatory   = 1,
+		.connection  = px4_hw_con_connector,
+	},
+	{
+		.id          = PX4_MFT_T100_ETH,
+		.present     = 1,
+		.mandatory   = 1,
+		.connection  = px4_hw_con_onboard,
+	},
+};
+
 
 static px4_hw_mft_list_entry_t mft_lists[] = {
 //  ver_rev
@@ -328,6 +369,7 @@ static px4_hw_mft_list_entry_t mft_lists[] = {
 	{HW_BASE_ID(9),  base_configuration_9, arraySize(base_configuration_9)},  // Auterion Skynode ver 9
 	{HW_BASE_ID(10), base_configuration_9, arraySize(base_configuration_9)},  // Auterion Skynode ver 10
 	{HW_BASE_ID(16), base_configuration_0, arraySize(base_configuration_0)},  // Auterion Skynode ver 16
+	{HW_BASE_ID(17), base_configuration_17, arraySize(base_configuration_17)},  // Auterion Skynode ver 17
 };
 
 /************************************************************************************

platforms/common/px4_log.cpp

@@ -74,7 +74,7 @@ void px4_log_initialize(void)
 	log_message.severity = 6; // info
 	strcpy((char *)log_message.text, "initialized uORB logging");
 	log_message.timestamp = hrt_absolute_time();
-	orb_log_message_pub = orb_advertise_queue(ORB_ID(log_message), &log_message, log_message_s::ORB_QUEUE_LENGTH);
+	orb_log_message_pub = orb_advertise(ORB_ID(log_message), &log_message);
 }
 
 __EXPORT void px4_log_modulename(int level, const char *module_name, const char *fmt, ...)

platforms/common/uORB/Publication.hpp

@@ -48,24 +48,6 @@
 namespace uORB
 {
 
-template <typename U> class DefaultQueueSize
-{
-private:
-	template <typename T>
-	static constexpr uint8_t get_queue_size(decltype(T::ORB_QUEUE_LENGTH) *)
-	{
-		return T::ORB_QUEUE_LENGTH;
-	}
-
-	template <typename T> static constexpr uint8_t get_queue_size(...)
-	{
-		return 1;
-	}
-
-public:
-	static constexpr unsigned value = get_queue_size<U>(nullptr);
-};
-
 class PublicationBase
 {
 public:
@@ -97,7 +79,7 @@ protected:
 /**
  * uORB publication wrapper class
  */
-template<typename T, uint8_t ORB_QSIZE = DefaultQueueSize<T>::value>
+template<typename T>
 class Publication : public PublicationBase
 {
 public:
@@ -113,7 +95,7 @@ public:
 	bool advertise()
 	{
 		if (!advertised()) {
-			_handle = orb_advertise_queue(get_topic(), nullptr, ORB_QSIZE);
+			_handle = orb_advertise(get_topic(), nullptr);
 		}
 
 		return advertised();

platforms/common/uORB/PublicationMulti.hpp

@@ -51,7 +51,7 @@ namespace uORB
 /**
  * Base publication multi wrapper class
  */
-template<typename T, uint8_t QSIZE = DefaultQueueSize<T>::value>
+template<typename T>
 class PublicationMulti : public PublicationBase
 {
 public:
@@ -73,7 +73,7 @@ public:
 	{
 		if (!advertised()) {
 			int instance = 0;
-			_handle = orb_advertise_multi_queue(get_topic(), nullptr, &instance, QSIZE);
+			_handle = orb_advertise_multi(get_topic(), nullptr, &instance);
 		}
 
 		return advertised();

platforms/common/uORB/uORB.cpp

@@ -118,22 +118,11 @@ orb_advert_t orb_advertise(const struct orb_metadata *meta, const void *data)
 	return uORB::Manager::get_instance()->orb_advertise(meta, data);
 }
 
-orb_advert_t orb_advertise_queue(const struct orb_metadata *meta, const void *data, unsigned int queue_size)
-{
-	return uORB::Manager::get_instance()->orb_advertise(meta, data, queue_size);
-}
-
 orb_advert_t orb_advertise_multi(const struct orb_metadata *meta, const void *data, int *instance)
 {
 	return uORB::Manager::get_instance()->orb_advertise_multi(meta, data, instance);
 }
 
-orb_advert_t orb_advertise_multi_queue(const struct orb_metadata *meta, const void *data, int *instance,
-				       unsigned int queue_size)
-{
-	return uORB::Manager::get_instance()->orb_advertise_multi(meta, data, instance, queue_size);
-}
-
 int orb_unadvertise(orb_advert_t handle)
 {
 	return uORB::Manager::get_instance()->orb_unadvertise(handle);
@@ -227,6 +216,14 @@ const char *orb_get_c_type(unsigned char short_type)
 	return nullptr;
 }
 
+uint8_t orb_get_queue_depth(const struct orb_metadata *meta)
+{
+	if (meta) {
+		return meta->o_queue;
+	}
+
+	return 0;
+}
 
 void orb_print_message_internal(const orb_metadata *meta, const void *data, bool print_topic_name)
 {

platforms/common/uORB/uORB.h

@@ -53,6 +53,8 @@ struct orb_metadata {
 	const uint16_t o_size_no_padding;   /**< object size w/o padding at the end (for logger) */
 	uint32_t message_hash;	/**< Hash over all fields for message compatibility checks */
 	orb_id_size_t  o_id;                /**< ORB_ID enum */
+	uint8_t o_queue;					/**< queue size */
+
 };
 
 typedef const struct orb_metadata *orb_id_t;
@@ -102,14 +104,16 @@ typedef const struct orb_metadata *orb_id_t;
  * @param _size_no_padding	Struct size w/o padding at the end
  * @param _message_hash	32 bit message hash over all fields
  * @param _orb_id_enum	ORB ID enum e.g.: ORB_ID::vehicle_status
+ * @param _queue_size Queue size from topic definition
  */
-#define ORB_DEFINE(_name, _struct, _size_no_padding, _message_hash, _orb_id_enum)		\
-	const struct orb_metadata __orb_##_name = {	\
-		#_name,					\
-		sizeof(_struct),		\
-		_size_no_padding,			\
-		_message_hash,				\
-		_orb_id_enum				\
+#define ORB_DEFINE(_name, _struct, _size_no_padding, _message_hash, _orb_id_enum, _queue_size)               \
+	const struct orb_metadata __orb_##_name = {     \
+		#_name,                                 \
+		sizeof(_struct),                \
+		_size_no_padding,                       \
+		_message_hash,                          \
+		_orb_id_enum,                           \
+		_queue_size                             \
 	}; struct hack
 
 __BEGIN_DECLS
@@ -135,23 +139,11 @@ typedef void 	*orb_advert_t;
  */
 extern orb_advert_t orb_advertise(const struct orb_metadata *meta, const void *data) __EXPORT;
 
-/**
- * @see uORB::Manager::orb_advertise()
- */
-extern orb_advert_t orb_advertise_queue(const struct orb_metadata *meta, const void *data,
-					unsigned int queue_size) __EXPORT;
-
 /**
  * @see uORB::Manager::orb_advertise_multi()
  */
 extern orb_advert_t orb_advertise_multi(const struct orb_metadata *meta, const void *data, int *instance) __EXPORT;
 
-/**
- * @see uORB::Manager::orb_advertise_multi()
- */
-extern orb_advert_t orb_advertise_multi_queue(const struct orb_metadata *meta, const void *data, int *instance,
-		unsigned int queue_size) __EXPORT;
-
 /**
  * @see uORB::Manager::orb_unadvertise()
  */
@@ -160,7 +152,7 @@ extern int orb_unadvertise(orb_advert_t handle) __EXPORT;
 /**
  * @see uORB::Manager::orb_publish()
  */
-extern int	orb_publish(const struct orb_metadata *meta, orb_advert_t handle, const void *data) __EXPORT;
+extern int orb_publish(const struct orb_metadata *meta, orb_advert_t handle, const void *data) __EXPORT;
 
 /**
  * Advertise as the publisher of a topic.
@@ -241,6 +233,12 @@ extern int	orb_get_interval(int handle, unsigned *interval) __EXPORT;
  */
 const char *orb_get_c_type(unsigned char short_type);
 
+/**
+ * Returns the queue depth of a topic
+ * @param meta orb topic metadata
+ */
+extern uint8_t orb_get_queue_depth(const struct orb_metadata *meta);
+
 /**
  * Print a topic to console. Do not call this directly, use print_message() instead.
  * @param meta orb topic metadata

platforms/common/uORB/uORBDeviceNode.cpp

@@ -73,12 +73,10 @@ static inline uint8_t round_pow_of_two_8(uint8_t n)
 	return value + 1;
 }
 
-uORB::DeviceNode::DeviceNode(const struct orb_metadata *meta, const uint8_t instance, const char *path,
-			     uint8_t queue_size) :
+uORB::DeviceNode::DeviceNode(const struct orb_metadata *meta, const uint8_t instance, const char *path) :
 	CDev(strdup(path)), // success is checked in CDev::init
 	_meta(meta),
-	_instance(instance),
-	_queue_size(round_pow_of_two_8(queue_size))
+	_instance(instance)
 {
 }
 
@@ -186,7 +184,7 @@ uORB::DeviceNode::write(cdev::file_t *filp, const char *buffer, size_t buflen)
 
 			/* re-check size */
 			if (nullptr == _data) {
-				const size_t data_size = _meta->o_size * _queue_size;
+				const size_t data_size = _meta->o_size * _meta->o_queue;
 				_data = (uint8_t *) px4_cache_aligned_alloc(data_size);
 
 				if (_data) {
@@ -217,7 +215,7 @@ uORB::DeviceNode::write(cdev::file_t *filp, const char *buffer, size_t buflen)
 	/* wrap-around happens after ~49 days, assuming a publisher rate of 1 kHz */
 	unsigned generation = _generation.fetch_add(1);
 
-	memcpy(_data + (_meta->o_size * (generation % _queue_size)), buffer, _meta->o_size);
+	memcpy(_data + (_meta->o_size * (generation % _meta->o_queue)), buffer, _meta->o_size);
 
 	// callbacks
 	for (auto item : _callbacks) {
@@ -254,13 +252,6 @@ uORB::DeviceNode::ioctl(cdev::file_t *filp, int cmd, unsigned long arg)
 		*(uintptr_t *)arg = (uintptr_t)this;
 		return PX4_OK;
 
-	case ORBIOCSETQUEUESIZE: {
-			lock();
-			int ret = update_queue_size(arg);
-			unlock();
-			return ret;
-		}
-
 	case ORBIOCGETINTERVAL:
 		*(unsigned *)arg = filp_to_subscription(filp)->get_interval_us();
 		return PX4_OK;
@@ -389,12 +380,11 @@ uORB::DeviceNode::print_statistics(int max_topic_length)
 
 	const uint8_t instance = get_instance();
 	const int8_t sub_count = subscriber_count();
-	const uint8_t queue_size = get_queue_size();
 
 	unlock();
 
 	PX4_INFO_RAW("%-*s %2i %4i %2i %4i %s\n", max_topic_length, get_meta()->o_name, (int)instance, (int)sub_count,
-		     queue_size, get_meta()->o_size, get_devname());
+		     get_meta()->o_queue, get_meta()->o_size, get_devname());
 
 	return true;
 }
@@ -483,21 +473,6 @@ int16_t uORB::DeviceNode::process_received_message(int32_t length, uint8_t *data
 }
 #endif /* CONFIG_ORB_COMMUNICATOR */
 
-int uORB::DeviceNode::update_queue_size(unsigned int queue_size)
-{
-	if (_queue_size == queue_size) {
-		return PX4_OK;
-	}
-
-	//queue size is limited to 255 for the single reason that we use uint8 to store it
-	if (_data || _queue_size > queue_size || queue_size > 255) {
-		return PX4_ERROR;
-	}
-
-	_queue_size = round_pow_of_two_8(queue_size);
-	return PX4_OK;
-}
-
 unsigned uORB::DeviceNode::get_initial_generation()
 {
 	ATOMIC_ENTER;

platforms/common/uORB/uORBDeviceNode.hpp

@@ -62,7 +62,7 @@ class UnitTest;
 class uORB::DeviceNode : public cdev::CDev, public IntrusiveSortedListNode<uORB::DeviceNode *>
 {
 public:
-	DeviceNode(const struct orb_metadata *meta, const uint8_t instance, const char *path, uint8_t queue_size = 1);
+	DeviceNode(const struct orb_metadata *meta, const uint8_t instance, const char *path);
 	virtual ~DeviceNode();
 
 	// no copy, assignment, move, move assignment
@@ -179,15 +179,6 @@ public:
 
 	void mark_as_advertised() { _advertised = true; }
 
-	/**
-	 * Try to change the size of the queue. This can only be done as long as nobody published yet.
-	 * This is the case, for example when orb_subscribe was called before an orb_advertise.
-	 * The queue size can only be increased.
-	 * @param queue_size new size of the queue
-	 * @return PX4_OK if queue size successfully set
-	 */
-	int update_queue_size(unsigned int queue_size);
-
 	/**
 	 * Print statistics
 	 * @param max_topic_length max topic name length for printing
@@ -195,7 +186,7 @@ public:
 	 */
 	bool print_statistics(int max_topic_length);
 
-	uint8_t get_queue_size() const { return _queue_size; }
+	uint8_t get_queue_size() const { return _meta->o_queue; }
 
 	int8_t subscriber_count() const { return _subscriber_count; }
 
@@ -234,7 +225,7 @@ public:
 	bool copy(void *dst, unsigned &generation)
 	{
 		if ((dst != nullptr) && (_data != nullptr)) {
-			if (_queue_size == 1) {
+			if (_meta->o_queue == 1) {
 				ATOMIC_ENTER;
 				memcpy(dst, _data, _meta->o_size);
 				generation = _generation.load();
@@ -253,12 +244,12 @@ public:
 				}
 
 				// Compatible with normal and overflow conditions
-				if (!is_in_range(current_generation - _queue_size, generation, current_generation - 1)) {
+				if (!is_in_range(current_generation - _meta->o_queue, generation, current_generation - 1)) {
 					// Reader is too far behind: some messages are lost
-					generation = current_generation - _queue_size;
+					generation = current_generation - _meta->o_queue;
 				}
 
-				memcpy(dst, _data + (_meta->o_size * (generation % _queue_size)), _meta->o_size);
+				memcpy(dst, _data + (_meta->o_size * (generation % _meta->o_queue)), _meta->o_size);
 				ATOMIC_LEAVE;
 
 				++generation;
@@ -295,7 +286,7 @@ private:
 
 	const uint8_t _instance; /**< orb multi instance identifier */
 	bool _advertised{false};  /**< has ever been advertised (not necessarily published data yet) */
-	uint8_t _queue_size; /**< maximum number of elements in the queue */
+
 	int8_t _subscriber_count{0};
 
 

platforms/common/uORB/uORBManager.cpp

@@ -265,8 +265,7 @@ int uORB::Manager::orb_exists(const struct orb_metadata *meta, int instance)
 	return ret;
 }
 
-orb_advert_t uORB::Manager::orb_advertise_multi(const struct orb_metadata *meta, const void *data, int *instance,
-		unsigned int queue_size)
+orb_advert_t uORB::Manager::orb_advertise_multi(const struct orb_metadata *meta, const void *data, int *instance)
 {
 #ifdef ORB_USE_PUBLISHER_RULES
 
@@ -300,19 +299,10 @@ orb_advert_t uORB::Manager::orb_advertise_multi(const struct orb_metadata *meta,
 		return nullptr;
 	}
 
-	/* Set the queue size. This must be done before the first publication; thus it fails if
-	 * this is not the first advertiser.
-	 */
-	int result = px4_ioctl(fd, ORBIOCSETQUEUESIZE, (unsigned long)queue_size);
-
-	if (result < 0 && queue_size > 1) {
-		PX4_WARN("orb_advertise_multi: failed to set queue size");
-	}
-
 	/* get the advertiser handle and close the node */
 	orb_advert_t advertiser;
 
-	result = px4_ioctl(fd, ORBIOCGADVERTISER, (unsigned long)&advertiser);
+	int result = px4_ioctl(fd, ORBIOCGADVERTISER, (unsigned long)&advertiser);
 	px4_close(fd);
 
 	if (result == PX4_ERROR) {
@@ -602,6 +592,22 @@ int16_t uORB::Manager::process_remote_topic(const char *topic_name)
 {
 	PX4_DEBUG("entering process_remote_topic: name: %s", topic_name);
 
+	// First make sure this is a valid topic
+	const struct orb_metadata *const *topic_list = orb_get_topics();
+	orb_id_t topic_ptr = nullptr;
+
+	for (size_t i = 0; i < orb_topics_count(); i++) {
+		if (strcmp(topic_list[i]->o_name, topic_name) == 0) {
+			topic_ptr = topic_list[i];
+			break;
+		}
+	}
+
+	if (! topic_ptr) {
+		PX4_ERR("process_remote_topic meta not found for %s\n", topic_name);
+		return -1;
+	}
+
 	// Look to see if we already have a node for this topic
 	char nodepath[orb_maxpath];
 	int ret = uORB::Utils::node_mkpath(nodepath, topic_name);
@@ -613,7 +619,7 @@ int16_t uORB::Manager::process_remote_topic(const char *topic_name)
 			uORB::DeviceNode *node = device_master->getDeviceNode(nodepath);
 
 			if (node) {
-				PX4_INFO("Marking DeviceNode(%s) as advertised in process_remote_topic", topic_name);
+				PX4_DEBUG("Marking DeviceNode(%s) as advertised in process_remote_topic", topic_name);
 				node->mark_as_advertised();
 				_remote_topics.insert(topic_name);
 				return 0;
@@ -622,27 +628,9 @@ int16_t uORB::Manager::process_remote_topic(const char *topic_name)
 	}
 
 	// We didn't find a node so we need to create it via an advertisement
-	const struct orb_metadata *const *topic_list = orb_get_topics();
-	orb_id_t topic_ptr = nullptr;
-
-	for (size_t i = 0; i < orb_topics_count(); i++) {
-		if (strcmp(topic_list[i]->o_name, topic_name) == 0) {
-			topic_ptr = topic_list[i];
-			break;
-		}
-	}
-
-	if (topic_ptr) {
-		PX4_INFO("Advertising remote topic %s", topic_name);
-		_remote_topics.insert(topic_name);
-		// Add some queue depth when advertising remote topics. These
-		// topics may get aggregated and thus delivered in a batch that
-		// requires some buffering in a queue.
-		orb_advertise(topic_ptr, nullptr, 5);
-
-	} else {
-		PX4_INFO("process_remote_topic meta not found for %s\n", topic_name);
-	}
+	PX4_DEBUG("Advertising remote topic %s", topic_name);
+	_remote_topics.insert(topic_name);
+	orb_advertise(topic_ptr, nullptr, topic_ptr->o_queue);
 
 	return 0;
 }
@@ -663,8 +651,11 @@ int16_t uORB::Manager::process_add_subscription(const char *messageName)
 			PX4_DEBUG("DeviceNode(%s) not created yet", messageName);
 
 		} else {
-			// node is present.
-			node->process_add_subscription();
+			// node is present. But don't send any data to it if it
+			// is a node advertised by the remote side
+			if (_remote_topics.find(messageName) == false) {
+				node->process_add_subscription();
+			}
 		}
 
 	} else {

platforms/common/uORB/uORBManager.hpp

@@ -215,17 +215,15 @@ public:
 	 * @param data    A pointer to the initial data to be published.
 	 *      For topics updated by interrupt handlers, the advertisement
 	 *      must be performed from non-interrupt context.
-	 * @param queue_size  Maximum number of buffered elements. If this is 1, no queuing is
-	 *      used.
 	 * @return    nullptr on error, otherwise returns an object pointer
 	 *      that can be used to publish to the topic.
 	 *      If the topic in question is not known (due to an
 	 *      ORB_DEFINE with no corresponding ORB_DECLARE)
 	 *      this function will return nullptr and set errno to ENOENT.
 	 */
-	orb_advert_t orb_advertise(const struct orb_metadata *meta, const void *data, unsigned int queue_size = 1)
+	orb_advert_t orb_advertise(const struct orb_metadata *meta, const void *data = nullptr)
 	{
-		return orb_advertise_multi(meta, data, nullptr, queue_size);
+		return orb_advertise_multi(meta, data, nullptr);
 	}
 
 	/**
@@ -250,16 +248,13 @@ public:
 	 * @param instance  Pointer to an integer which will yield the instance ID (0-based)
 	 *      of the publication. This is an output parameter and will be set to the newly
 	 *      created instance, ie. 0 for the first advertiser, 1 for the next and so on.
-	 * @param queue_size  Maximum number of buffered elements. If this is 1, no queuing is
-	 *      used.
 	 * @return    nullptr on error, otherwise returns a handle
 	 *      that can be used to publish to the topic.
 	 *      If the topic in question is not known (due to an
 	 *      ORB_DEFINE with no corresponding ORB_DECLARE)
 	 *      this function will return nullptr and set errno to ENOENT.
 	 */
-	orb_advert_t orb_advertise_multi(const struct orb_metadata *meta, const void *data, int *instance,
-					 unsigned int queue_size = 1);
+	orb_advert_t orb_advertise_multi(const struct orb_metadata *meta, const void *data, int *instance);
 
 	/**
 	 * Unadvertise a topic.

platforms/common/uORB/uORBManagerUsr.cpp

@@ -89,8 +89,7 @@ int uORB::Manager::orb_exists(const struct orb_metadata *meta, int instance)
 	return data.ret;
 }
 
-orb_advert_t uORB::Manager::orb_advertise_multi(const struct orb_metadata *meta, const void *data, int *instance,
-		unsigned int queue_size)
+orb_advert_t uORB::Manager::orb_advertise_multi(const struct orb_metadata *meta, const void *data, int *instance)
 {
 	/* open the node as an advertiser */
 	int fd = node_open(meta, true, instance);
@@ -100,19 +99,10 @@ orb_advert_t uORB::Manager::orb_advertise_multi(const struct orb_metadata *meta,
 		return nullptr;
 	}
 
-	/* Set the queue size. This must be done before the first publication; thus it fails if
-	 * this is not the first advertiser.
-	 */
-	int result = px4_ioctl(fd, ORBIOCSETQUEUESIZE, (unsigned long)queue_size);
-
-	if (result < 0 && queue_size > 1) {
-		PX4_WARN("orb_advertise_multi: failed to set queue size");
-	}
-
 	/* get the advertiser handle and close the node */
 	orb_advert_t advertiser;
 
-	result = px4_ioctl(fd, ORBIOCGADVERTISER, (unsigned long)&advertiser);
+	int result = px4_ioctl(fd, ORBIOCGADVERTISER, (unsigned long)&advertiser);
 	px4_close(fd);
 
 	if (result == PX4_ERROR) {

platforms/common/uORB/uORB_tests/uORBTest_UnitTest.cpp

@@ -574,8 +574,8 @@ int uORBTest::UnitTest::test_wrap_around()
 	bool updated{false};
 
 	// Advertise but not publish topics, only generate device_node, which is convenient for modifying DeviceNode::_generation
-	const int queue_size = 16;
-	ptopic = orb_advertise_queue(ORB_ID(orb_test_medium_wrap_around), nullptr, queue_size);
+	const int queue_size = orb_test_medium_s::ORB_QUEUE_LENGTH;
+	ptopic = orb_advertise(ORB_ID(orb_test_medium_wrap_around), nullptr);
 
 	if (ptopic == nullptr) {
 		return test_fail("advertise failed: %d", errno);
@@ -828,9 +828,9 @@ int uORBTest::UnitTest::test_queue()
 		return test_fail("subscribe failed: %d", errno);
 	}
 
-	const int queue_size = 16;
+	const int queue_size = orb_test_medium_s::ORB_QUEUE_LENGTH;
 	orb_test_medium_s t{};
-	ptopic = orb_advertise_queue(ORB_ID(orb_test_medium_queue), &t, queue_size);
+	ptopic = orb_advertise(ORB_ID(orb_test_medium_queue), &t);
 
 	if (ptopic == nullptr) {
 		return test_fail("advertise failed: %d", errno);
@@ -935,9 +935,9 @@ int uORBTest::UnitTest::pub_test_queue_main()
 {
 	orb_test_medium_s t{};
 	orb_advert_t ptopic{nullptr};
-	const int queue_size = 50;
+	const int queue_size = orb_test_medium_s::ORB_QUEUE_LENGTH;
 
-	if ((ptopic = orb_advertise_queue(ORB_ID(orb_test_medium_queue_poll), &t, queue_size)) == nullptr) {
+	if ((ptopic = orb_advertise(ORB_ID(orb_test_medium_queue_poll), &t)) == nullptr) {
 		_thread_should_exit = true;
 		return test_fail("advertise failed: %d", errno);
 	}

platforms/posix/src/px4/common/px4_init.cpp

@@ -40,15 +40,34 @@
 #include <px4_platform_common/px4_work_queue/WorkQueueManager.hpp>
 #include <uORB/uORB.h>
 
+#if defined(CONFIG_MODULES_MUORB_APPS)
+extern "C" { int muorb_init(); }
+#endif
+
 int px4_platform_init(void)
 {
 	hrt_init();
 
 	px4::WorkQueueManagerStart();
 
+// MUORB has slightly different startup requirements
+#if defined(CONFIG_MODULES_MUORB_APPS)
+	//Put sleeper in here to allow wq to finish initializing before param_init is called
+	usleep(10000);
+
+	uorb_start();
+
+	muorb_init();
+
+	// Give muorb some time to setup the DSP
+	usleep(100000);
+
+	param_init();
+#else
 	param_init();
 
 	uorb_start();
+#endif
 
 	px4_log_initialize();
 

platforms/ros2/include/uORB/Publication.hpp

@@ -45,28 +45,10 @@
 namespace uORB
 {
 
-template <typename U> class DefaultQueueSize
-{
-private:
-	template <typename T>
-	static constexpr uint8_t get_queue_size(decltype(T::ORB_QUEUE_LENGTH) *)
-	{
-		return T::ORB_QUEUE_LENGTH;
-	}
-
-	template <typename T> static constexpr uint8_t get_queue_size(...)
-	{
-		return 1;
-	}
-
-public:
-	static constexpr unsigned value = get_queue_size<U>(nullptr);
-};
-
 /**
  * uORB publication wrapper class
  */
-template<typename T, uint8_t ORB_QSIZE = DefaultQueueSize<T>::value>
+template<typename T>
 class Publication
 {
 public:

src/drivers/barometer/bmp388/bmp388.cpp

@@ -77,6 +77,7 @@ BMP388::init()
 
 	if (_chip_id == BMP390_CHIP_ID) {
 		_interface->set_device_type(DRV_BARO_DEVTYPE_BMP390);
+		this->_item_name = "bmp390";
 	}
 
 	_chip_rev_id = _interface->get_reg(BMP3_REV_ID_ADDR);

src/drivers/barometer/invensense/icp201xx/ICP201XX.cpp

@@ -251,7 +251,7 @@ ICP201XX::RunImpl()
 	case STATE::CONFIG: {
 			if (configure()) {
 				_state = STATE::WAIT_READ;
-				ScheduleDelayed(30_ms);
+				ScheduleDelayed(50_ms);
 
 			} else {
 				if (hrt_elapsed_time(&_reset_timestamp) > 1000_ms) {

src/drivers/batt_smbus/batt_smbus.cpp

@@ -392,6 +392,12 @@ int BATT_SMBUS::get_startup_info()
 	uint16_t state_of_health;
 	ret |= _interface->read_word(BATT_SMBUS_STATE_OF_HEALTH, state_of_health);
 
+	/* ManufacturerAccess dummy command to init the ManufacturerBlockAccess routine
+	in the BQ40Zx0 and avoid timeout during LifetimeDataFlush.
+	test Sleep > 20 ms to give time to init the ManufacturerBlockAccess routine*/
+	ret |= _interface->write_word(BATT_SMBUS_MANUFACTURER_ACCESS, BATT_SMBUS_DEVICE_TYPE);
+	px4_usleep(30_ms);
+
 	if (!ret) {
 		_serial_number = serial_num;
 		_batt_startup_capacity = (uint16_t)((float)remaining_cap * _c_mult);

src/drivers/batt_smbus/batt_smbus.h

@@ -107,6 +107,7 @@ using namespace time_literals;
 
 #define BATT_SMBUS_SECURITY_KEYS                        0x0035
 
+#define BATT_SMBUS_DEVICE_TYPE                          0x0001
 #define BATT_SMBUS_LIFETIME_FLUSH                       0x002E
 #define BATT_SMBUS_LIFETIME_BLOCK_ONE                   0x0060
 #define BATT_SMBUS_ENABLED_PROTECTIONS_A_ADDRESS        0x4938

src/drivers/camera_trigger/camera_trigger.cpp

@@ -314,7 +314,7 @@ CameraTrigger::CameraTrigger() :
 	// Advertise critical publishers here, because we cannot advertise in interrupt context
 	camera_trigger_s trigger{};
 
-	_trigger_pub = orb_advertise_queue(ORB_ID(camera_trigger), &trigger, camera_trigger_s::ORB_QUEUE_LENGTH);
+	_trigger_pub = orb_advertise(ORB_ID(camera_trigger), &trigger);
 }
 
 CameraTrigger::~CameraTrigger()

src/drivers/distance_sensor/cm8jl65/CM8JL65.cpp

@@ -113,7 +113,7 @@ CM8JL65::CM8JL65(const char *port, uint8_t rotation) :
 	_px4_rangefinder.set_max_distance(7.9f);	// Datasheet: 8.0m
 	_px4_rangefinder.set_fov(0.0488692f);
 	_px4_rangefinder.set_device_type(DRV_DIST_DEVTYPE_CM8JL65);
-	_px4_rangefinder.set_rangefinder_type(distance_sensor_s::MAV_DISTANCE_SENSOR_LASER);
+	_px4_rangefinder.set_rangefinder_type(distance_sensor_s::MAV_DISTANCE_SENSOR_INFRARED);
 }
 
 CM8JL65::~CM8JL65()

src/drivers/drv_orb_dev.h

@@ -64,13 +64,10 @@
 /** Get the priority for the topic */
 #define ORBIOCGPRIORITY		_ORBIOC(14)
 
-/** Set the queue size of the topic */
-#define ORBIOCSETQUEUESIZE	_ORBIOC(15)
-
 /** Get the minimum interval at which the topic can be seen to be updated for this subscription */
-#define ORBIOCGETINTERVAL	_ORBIOC(16)
+#define ORBIOCGETINTERVAL	_ORBIOC(15)
 
 /** Check whether the topic is advertised, sets *(unsigned long *)arg to 1 if advertised, 0 otherwise */
-#define ORBIOCISADVERTISED	_ORBIOC(17)
+#define ORBIOCISADVERTISED	_ORBIOC(16)
 
 #endif /* _DRV_UORB_H */

src/drivers/imu/invensense/icm42688p/ICM42688P.hpp

@@ -88,7 +88,7 @@ private:
 		FIFO::DATA f[FIFO_MAX_SAMPLES] {};
 	};
 	// ensure no struct padding
-	static_assert(sizeof(FIFOTransferBuffer) == (4 + FIFO_MAX_SAMPLES *sizeof(FIFO::DATA)));
+	static_assert(sizeof(FIFOTransferBuffer) == (4 + FIFO_MAX_SAMPLES *sizeof(FIFO::DATA)), "Invalid transfer buffer size");
 
 	struct register_bank0_config_t {
 		Register::BANK_0 reg;

src/drivers/pwm_out/PWMOut.cpp

@@ -229,7 +229,7 @@ void PWMOut::update_params()
 					if (output_function >= (int)OutputFunction::Servo1
 					    && output_function <= (int)OutputFunction::ServoMax) { // Function got set to a servo
 						int32_t val = 1500;
-						PX4_INFO("Setting channel %i disarmed to %i", (int) val, i);
+						PX4_INFO("Setting channel %i disarmed to %i", i + 1, (int)val);
 						param_set(_mixing_output.disarmedParamHandle(i), &val);
 
 						// If the whole timer group was not set previously, then set the pwm rate to 50 Hz
@@ -250,7 +250,7 @@ void PWMOut::update_params()
 
 								if (param_get(handle, &tim_config) == 0 && tim_config == 400) {
 									tim_config = 50;
-									PX4_INFO("setting timer %i to %i Hz", timer, (int) tim_config);
+									PX4_INFO("Setting timer %i to %i Hz", timer, (int)tim_config);
 									param_set(handle, &tim_config);
 								}
 							}
@@ -261,10 +261,10 @@ void PWMOut::update_params()
 					if (output_function >= (int)OutputFunction::Motor1
 					    && output_function <= (int)OutputFunction::MotorMax) { // Function got set to a motor
 						int32_t val = 1100;
-						PX4_INFO("Setting channel %i minimum to %i", (int) val, i);
+						PX4_INFO("Setting channel %i minimum to %i", i + 1, (int)val);
 						param_set(_mixing_output.minParamHandle(i), &val);
 						val = 1900;
-						PX4_INFO("Setting channel %i maximum to %i", (int) val, i);
+						PX4_INFO("Setting channel %i maximum to %i", i + 1, (int)val);
 						param_set(_mixing_output.maxParamHandle(i), &val);
 					}
 				}

src/drivers/px4io/px4io.cpp

@@ -705,7 +705,7 @@ void PX4IO::update_params()
 						if (output_function >= (int)OutputFunction::Servo1
 						    && output_function <= (int)OutputFunction::ServoMax) { // Function got set to a servo
 							int32_t val = 1500;
-							PX4_INFO("Setting channel %i disarmed to %i", (int) val, i);
+							PX4_INFO("Setting channel %i disarmed to %i", i + 1, (int)val);
 							param_set(_mixing_output.disarmedParamHandle(i), &val);
 
 							// If the whole timer group was not set previously, then set the pwm rate to 50 Hz
@@ -726,7 +726,7 @@ void PX4IO::update_params()
 
 									if (param_get(handle, &tim_config) == 0 && tim_config == 400) {
 										tim_config = 50;
-										PX4_INFO("setting timer %i to %i Hz", timer, (int) tim_config);
+										PX4_INFO("Setting timer %i to %i Hz", timer, (int)tim_config);
 										param_set(handle, &tim_config);
 									}
 								}
@@ -737,10 +737,10 @@ void PX4IO::update_params()
 						if (output_function >= (int)OutputFunction::Motor1
 						    && output_function <= (int)OutputFunction::MotorMax) { // Function got set to a motor
 							int32_t val = 1100;
-							PX4_INFO("Setting channel %i minimum to %i", (int) val, i);
+							PX4_INFO("Setting channel %i minimum to %i", i + 1, (int)val);
 							param_set(_mixing_output.minParamHandle(i), &val);
 							val = 1900;
-							PX4_INFO("Setting channel %i maximum to %i", (int) val, i);
+							PX4_INFO("Setting channel %i maximum to %i", i + 1, (int)val);
 							param_set(_mixing_output.maxParamHandle(i), &val);
 						}
 					}

src/drivers/tone_alarm/ToneAlarm.cpp

@@ -45,8 +45,6 @@ using namespace time_literals;
 ToneAlarm::ToneAlarm() :
 	ScheduledWorkItem(MODULE_NAME, px4::wq_configurations::hp_default)
 {
-	// ensure ORB_ID(tune_control) is advertised with correct queue depth
-	orb_advertise_queue(ORB_ID(tune_control), nullptr, tune_control_s::ORB_QUEUE_LENGTH);
 }
 
 ToneAlarm::~ToneAlarm()

src/drivers/voxl2_io/CMakeLists.txt

@@ -45,6 +45,7 @@ px4_add_module(
 		voxl2_io.cpp
 		voxl2_io.hpp
 	DEPENDS
+		rc
 		px4_work_queue
 		mixer_module
 	MODULE_CONFIG

src/lib/adsb/AdsbConflict.h

@@ -151,7 +151,7 @@ private:
 
 	transponder_report_s tr{};
 
-	orb_advert_t fake_traffic_report_publisher = orb_advertise_queue(ORB_ID(transponder_report), &tr, (unsigned int)20);
+	orb_advert_t fake_traffic_report_publisher = orb_advertise(ORB_ID(transponder_report), &tr);
 
 	TRAFFIC_STATE _traffic_state_previous{TRAFFIC_STATE::NO_CONFLICT};
 

src/lib/events/events.cpp

@@ -61,7 +61,7 @@ void send(EventType &event)
 		orb_publish(ORB_ID(event), orb_event_pub, &event);
 
 	} else {
-		orb_event_pub = orb_advertise_queue(ORB_ID(event), &event, event_s::ORB_QUEUE_LENGTH);
+		orb_event_pub = orb_advertise(ORB_ID(event), &event);
 	}
 
 	pthread_mutex_unlock(&publish_event_mutex);

src/lib/geo/test_geo.cpp

@@ -42,7 +42,7 @@ class GeoTest : public ::testing::Test
 public:
 	void SetUp() override
 	{
-		proj.initReference(math::radians(473566094 / 1e7), math::radians(85190237 / 1e7), 0);
+		proj.initReference(473566094 / 1e7, 85190237 / 1e7, 0);
 	}
 
 protected:
@@ -73,7 +73,7 @@ TEST_F(GeoTest, reprojectProject)
 
 TEST_F(GeoTest, projectReproject)
 {
-	// GIVEN: x and y coordinates in the local cartesian frame
+	// GIVEN: lat and lon coordinates in the geographic coordinate system
 	double lat = 47.356616973876953;
 	double lon = 8.5190505981445313;
 	float x;

src/lib/matrix/matrix/Matrix.hpp

@@ -162,6 +162,24 @@ public:
 		return res;
 	}
 
+	// Using this function reduces the number of temporary variables needed to compute A * B.T
+	template<size_t P>
+	Matrix<Type, M, M> multiplyByTranspose(const Matrix<Type, P, N> &other) const
+	{
+		Matrix<Type, M, P> res;
+		const Matrix<Type, M, N> &self = *this;
+
+		for (size_t i = 0; i < M; i++) {
+			for (size_t k = 0; k < P; k++) {
+				for (size_t j = 0; j < N; j++) {
+					res(i, k) += self(i, j) * other(k, j);
+				}
+			}
+		}
+
+		return res;
+	}
+
 	// Element-wise multiplication
 	Matrix<Type, M, N> emult(const Matrix<Type, M, N> &other) const
 	{
@@ -391,12 +409,6 @@ public:
 			for (unsigned j = 0; j < N; j++) {
 				double d = static_cast<double>(self(i, j));
 
-				// Matrix diagonal elements
-				if (N > 1 && M > 1 && i == j) {
-					// make diagonal elements bold (ANSI CSI n 1)
-					printf("\033[1m");
-				}
-
 				// if symmetric don't print upper triangular elements
 				if ((M == N) && (j > i) && (i < N) && (j < M)
 				    && (fabs(d - static_cast<double>(self(j, i))) < (double)eps)
@@ -417,12 +429,6 @@ public:
 						printf("% 6.5f ", d);
 					}
 				}
-
-				// Matrix diagonal elements
-				if (N > 1 && M > 1 && i == j) {
-					// reset any formatting (ANSI CSI n 0)
-					printf("\033[0m");
-				}
 			}
 
 			printf("\n");