- split out integrated data into new standalone messages (sensor_accel_integrated and sensor_gyro_integrated)
- publish sensor_gyro at full rate and remove sensor_gyro_control
- limit sensor status publications to 10 Hz
- remove unused accel/gyro raw ADC fields
- add device IDs to sensor_bias and sensor_correction
- vehicle_angular_velocity/vehicle_acceleration: check device ids before using bias and corrections
- this provides some extra space when the FIFO transfers don't align perfectly
- I've also made an effort to keep the different drivers (icm20602, icm20608g, ism330ldc) in sync so we can factor out the common portions later once we've confident in the pattern.
* Treat UAVS diffrently from manned aviation
* Added fake_traffic testing functionality,
* Added NAV_TRAFF_AVOID Hold and Landmode
* Added Behavior: HOLD Position to collision avoidance mode and implemented Landmode to collision avoidance.
Boards where no Hardware GUID is defined will send 0 as GUID.
Right now collision avoidance for more than one FMU without Hardware GUID is not possible.
We should consider adding a randomly generated HW GUID as a placeholder for legacy Boards
We now check individually for empy and genmsg.
Also, my recommendation is to use pip3 as a user to install the
dependencies as this is least intrusive and should work on all
platforms.
* parameter and logic to commander for triggering failsafe from external automatic trigger system.
* logic to startup script for enabling ATS. Added uORB publishing to pwm_input module.
* Refactored out CDev usage from pwm_input and ll40ls. Refactored out ll40ls specifics from pwm_input and cleaned up dead code.
- rename of flag in position sp: from allow_weather_vane to disable_weather_vane
- flag now doesn't have to be set for all auto modes, meaning that weather vane is also active outside of mission
- flag is set before front transition to align with wp, and unset after alignment is over
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- uses the FIFO and SPI DMA to transfer full raw data (8 kHz gyro, 4 kHz accel)
- new sensor messages for better visibility
- sensor_{accel, gyro}_fifo: full raw data for optional logging and analysis
- sensor_{accel, gyro}_status: metadata, clipping, etc
- currently not enabled by default
- gencpp in PX4/Firmware (d5fb89ee02f4c7e6c44e27c31e7f535d0aa0da0c): 7e446a9976
- gencpp current upstream: ff6c9f3e8e
- Changes: 7e446a9976...ff6c9f3e8e
ff6c9f3 2019-11-11 Jochen Sprickerhof - Two patches to make the generated headers reproducible (#42)
e12443e 2019-03-18 Dirk Thomas - 0.6.2
d227d17 2019-03-18 Dirk Thomas - update changelog
e233144 2019-03-15 Martin Pecka - Added plugins the ability to also generate free functions. (#40)
40559af 2019-03-04 Dirk Thomas - 0.6.1
96ec7f1 2019-03-04 Dirk Thomas - update changelog
* FW attitude controller, FW position controller and VTOL attitude controller subscribe to airspeed_validated topic
* add possibility to switch off the airspeed valid checks
* remove airspeed valid checks from commander
* clean up of VTOL transition logic
* Airspeed Selector: remove dynamic allocation of airspeed validators (depending on number of connected sensors) but do it statically for the maximum number allowed. Check for number of connected sensors not only during start up, but always when vehicle is disarmed.
* Airspeed Selector: change work queue from lp to att_pos_ctrl as this module is safety-critical
* add airspeed selector to px4_fmu-v2 defaults
esc_setpoint in UAVCAN was just wrong, this is what it really is:
uint7 power_rating_pct # Instant demand factor in percent
(percent of maximum power); range 0% to 127%.
and remove the px4_ prefix, except for px4_config.h.
command to update includes:
for k in app.h atomic.h cli.h console_buffer.h defines.h getopt.h i2c.h init.h log.h micro_hal.h module.h module_params.h param.h param_macros.h posix.h sem.h sem.hpp shmem.h shutdown.h tasks.h time.h workqueue.h; do for i in $(grep -rl 'include <px4_'$k src platforms boards); do sed -i 's/#include <px4_'$k'/#include <px4_platform_common\/'$k/ $i; done; done
for in $(grep -rl 'include <px4_config.h' src platforms boards); do sed -i 's/#include <px4_config.h/#include <px4_platform_common\/px4_config.h'/ $i; done
Transitional headers for submodules are added (px4_{defines,log,time}.h)
