- bit of clean up
- add GPS failsafe mode auto_altitude, that will keep current altitude with a fixed-bank angle
for some time, then switches to auto_descend that will descend with constant sink rate
of 0.5m/s
- params controlling GPS failsafe are not FW params: NAV_GPSF_R --> FW_GPSF_R and
NAV_GPSF_LT --> FW_GPSF_LT
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Signed-off-by: RomanBapst <bapstroman@gmail.com>
commander: support orbit mode for fixed wings
Signed-off-by: RomanBapst <bapstroman@gmail.com>
FwPositionControl: publish orbit status
Signed-off-by: RomanBapst <bapstroman@gmail.com>
commander:reject orbit mode while doing a vtol transition
Signed-off-by: RomanBapst <bapstroman@gmail.com>
FixedWingPositionControl: explicitly cast waypoint for Orbit status
FixedwingPositionControl: fill missing orbit_status fields
navigator_main: handle reposition/orbit corner cases
- set orbit rotation direction correctly
- send mavlink message when orbit is rejected
FixedWingPositionControl: correctly report rotation direction in orbit_status
navigator: hack to not break orbit while doing altitude changes
Signed-off-by: RomanBapst <bapstroman@gmail.com>
navigator: set cruise throttle for orbit command
Signed-off-by: RomanBapst <bapstroman@gmail.com>
This commit encapsulates the position setpoint and loiter setpoint handling into a single method, in order to make the code easier to understand
4be452
- avoids tecs always climbing and sinking and max rates and allows to fine tune these rates
- avoid numerical calculation of feedforward velocity using derivative, this
was prone to jitter in dt
Signed-off-by: RomanBapst <bapstroman@gmail.com>
- handle SET_POSITION_TARGET_LOCAL_NED and SET_POSITION_TARGET_GLOBAL_INT with ORB_ID(trajectory_setpoint)
- FlightTaskOffboard not needed at all
- bypass position_setpoint_triplet entirely (start removing extraneous fields)
- simplify offboard_control_mode to map to supported control modes
- parameter updates can be quite expensive because they trigger nearly all modules to reload all of their parameters immediately
- limit modules from updating faster than once per second
- this fixes the case where the navigator publishes a loiter waypoint or any
waypoint which is too close to the vehicle.
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* FW attitude controller, FW position controller and VTOL attitude controller subscribe to airspeed_validated topic
* add possibility to switch off the airspeed valid checks
* remove airspeed valid checks from commander
* clean up of VTOL transition logic
* Airspeed Selector: remove dynamic allocation of airspeed validators (depending on number of connected sensors) but do it statically for the maximum number allowed. Check for number of connected sensors not only during start up, but always when vehicle is disarmed.
* Airspeed Selector: change work queue from lp to att_pos_ctrl as this module is safety-critical
* add airspeed selector to px4_fmu-v2 defaults
and remove the px4_ prefix, except for px4_config.h.
command to update includes:
for k in app.h atomic.h cli.h console_buffer.h defines.h getopt.h i2c.h init.h log.h micro_hal.h module.h module_params.h param.h param_macros.h posix.h sem.h sem.hpp shmem.h shutdown.h tasks.h time.h workqueue.h; do for i in $(grep -rl 'include <px4_'$k src platforms boards); do sed -i 's/#include <px4_'$k'/#include <px4_platform_common\/'$k/ $i; done; done
for in $(grep -rl 'include <px4_config.h' src platforms boards); do sed -i 's/#include <px4_config.h/#include <px4_platform_common\/px4_config.h'/ $i; done
Transitional headers for submodules are added (px4_{defines,log,time}.h)
* adds a work_queue systemcmd that will bring a tree view of all active work queues and work items
* WorkQueues now track attached WorkItems and will shutdown when the last WorkItem is detached
Script to update include paths:
for i in $(grep -rl 'include <px4_work_queue' src platforms); do sed -i 's/#include <px4_work_queue/#include <px4_platform_common\/px4_work_queue/' $i; done
Silvan Fuhrer