This avoids the need for recalibration, and also cleans up other driver
ID's (merge separate accel/gyro).
The SPI address was previously set to a board-specific (arbitrary) value,
and is now set to 0. This will allow extending for multiple sensors of the
same type on the same bus.
Chip-select and SPI initialization uses the new config, whereas the drivers
still use the existing defines.
The configuration in board_config.h can be removed after all drivers are
updated.
- refactor Run() into simple state machine
- perform reset and configuration in sensor bus thread
- when using data ready interrupt skip checking FIFO count
- fix periodic temperature sampling (rate limit to 1 Hz)
- refactor Run() into simple state machine
- perform reset and configuration in sensor bus thread
- when using data ready interrupt skip checking FIFO count
- fix periodic temperature sampling (rate limit to 1 Hz)
- refactor Run() into simple state machine
- perform reset and configuration in sensor bus thread
- when using data ready interrupt skip checking FIFO count
- fix periodic temperature sampling (rate limit to 1 Hz)
- refactor Run() into simple state machine
- perform reset and configuration in sensor bus thread
- when using data ready interrupt skip checking FIFO count
- checked register mechanism and simple watchdog
- driver checks for errors gradually and can reconfigure itself
- respect IMU_GYRO_RATEMAX at the driver level
- fixed sensor INT16_MIN and INT16_MAX handling (y & z axis are flipped before publishing)
- checked register mechanism and simple watchdog
- driver checks for errors gradually and can reconfigure itself
- respect IMU_GYRO_RATEMAX at the driver level
- fixed sensor INT16_MIN and INT16_MAX handling (y & z axis are flipped before publishing)
- checked register mechanism and simple watchdog
- driver checks for errors gradually and can reconfigure itself
- respect IMU_GYRO_RATEMAX at the driver level
- fixed sensor INT16_MIN and INT16_MAX handling (y & z axis are flipped before publishing)
- checked register mechanism and simple watchdog
- driver checks for errors gradually and can reconfigure itself
- respect IMU_GYRO_RATEMAX at the driver level
- fixed sensor INT16_MIN and INT16_MAX handling (y & z axis are flipped before publishing)
- increased sensor_gyro_fifo max size (enables running the driver much slower, but still transferring all raw data)
- PX4Accelerometer/PX4Gyroscope remove unnecessary memsets
I've added a queue depth of 4 for sensor_accel and sensor_gyro. This is initially added because it's not always possible for the `vehicle_acceleration` to keep up with every publication of the primary accelerator as it runs in the same thread as ekf2, various controllers, etc.
Later this mechanism will be used in a few areas
- rate limit `vehicle_angular_velocity` and `vehicle_acceleration` without missing any raw data
- move IMU integration to `vehicle_imu` and out of the actual driver threads, eliminating the need for sensor_accel_integrated and sensor_gyro_integrated
- integrate raw gyro synchronized with optical flow measurements
- gyro filtering (low-pass and notch) only performed on primary gyro in `sensors/vehicle_angular_velocity` instead of every gyro in `PX4Gyroscope`
- sample rate is calculated from actual updates (the fixed value was slightly wrong in many cases, and very wrong in a few)
- In the FIFO case the array is now averaged and published in `sensor_gyro` for filtering downstream. I'll update this in the future to use the full FIFO array (if available), but right now it should be fine.
- this provides some extra space when the FIFO transfers don't align perfectly
- I've also made an effort to keep the different drivers (icm20602, icm20608g, ism330ldc) in sync so we can factor out the common portions later once we've confident in the pattern.
The sensor comes in three variants with different gyro measurement ranges. This patch allows auto-detection of the model at startup and sets the scale factor associated with the particular model.
- uses the FIFO and SPI DMA to transfer full raw data (8 kHz gyro, 4 kHz accel)
- new sensor messages for better visibility
- sensor_{accel, gyro}_fifo: full raw data for optional logging and analysis
- sensor_{accel, gyro}_status: metadata, clipping, etc
- currently not enabled by default
This should fix spikes in the mag data on MPU9250 found inside Drotek
Pixhawk 3Pro.
The problem turned out to be that we are not checking the DRDY bit
before reading the data. We presumably threw away most of the stale data
by doing a duplicate check, however, sometimes we might have run into a
race where the mag data was already being updated in the chip while
still being read.
and remove the px4_ prefix, except for px4_config.h.
command to update includes:
for k in app.h atomic.h cli.h console_buffer.h defines.h getopt.h i2c.h init.h log.h micro_hal.h module.h module_params.h param.h param_macros.h posix.h sem.h sem.hpp shmem.h shutdown.h tasks.h time.h workqueue.h; do for i in $(grep -rl 'include <px4_'$k src platforms boards); do sed -i 's/#include <px4_'$k'/#include <px4_platform_common\/'$k/ $i; done; done
for in $(grep -rl 'include <px4_config.h' src platforms boards); do sed -i 's/#include <px4_config.h/#include <px4_platform_common\/px4_config.h'/ $i; done
Transitional headers for submodules are added (px4_{defines,log,time}.h)
* adds a work_queue systemcmd that will bring a tree view of all active work queues and work items
* WorkQueues now track attached WorkItems and will shutdown when the last WorkItem is detached
Beat Küng