- Enable arbitrary euler angle for Mag rotation
- new CUSTOM rotation enum out of the normal enum range
- mag_rot: automatically change to custom if euler rot is set
- sensor_calibration: Magnetometer save custom rotation parameters
- mag_cal: cross mention rotation parameters
- This allows the user to see the RPY options when searching for the rotation parameter
---------
Co-authored-by: Junwoo Hwang <junwoo@auterion.com>
Co-authored-by: bresch <[brescianimathieu@gmail.com](mailto:brescianimathieu@gmail.com)>
Co-authored-by: Daniel Agar <daniel@agar.ca>
- this was an experiment to casually monitor sensor offsets relative to temperature, but now that all calibration offsets can be adjusted post-flight the stored temperature can be misleading
- deleting to save a little bit of flash (and storing the temperature wasn't useful)
- centralize logic for selecting a preferred calibration slot
- automatically use existing calibration slot if it exists, otherwise
find first available slot, with a preference for a requested index
- existing commander calibration methods rewrite all calibration slots
to match current sensor ordering
In some cases, the fitness of the optimizer does not shrink at each
iteration, causing the "decreasing fitness check" to fail. This stops
the optimization and returns with sub-optimal, or unrealistic results.
- handle saving the mag bias per sensor (across all estimator instances using that mag) in sensors/vehicle_magnetometer
- this is now saving back to the actual mag calibration CAL_MAGn_OFF{X,Y,Z}
- ekf2 reset mag mag bias on any magnetometer or calibration change
- use Kalman filter scheme to update stored mag bias parameters using all available bias estimates for that sensor
Co-authored-by: Paul Riseborough <gncsolns@gmail.com>
- drivers/tone_alarm: move to ModuleBase and purge CDev (/dev/tone_alarm0)
- drivers/tone_alarm: only run on tune_control publication (or scheduled note) rather than continuously
- drivers/tone_alarm: use HRT to schedule tone stop (prevents potential disruption)
- msg/tune_control: add tune_id numbering
- systemcmds/tune_control: add "error" special case tune_id
- move all tune_control publication to new uORB::PublicationQueued<>
- start tone_alarm immediately after board defaults are loaded to fix potential startup issues
- for SITL (or other boards with no TONE output) print common messages (startup, error, etc)
- this allows the default priority to be set differently for internal/external sensors
- accel and gyro initialize default priority like mag in preparation for fully supporting external sensors
- fixes#15652
- use proper Mavlink MAV_CMD_FIXED_MAG_CAL_YAW command for initiating magnetometer quick cal
- MAV_CMD_FIXED_MAG_CAL_YAW allows specifying the yaw and optionally latitude and longitude if the vehicle doesn't have GPS
- remove all remaining IOCTLs for accel and gyro and handle all calibration entirely in sensors module with parameters
- sensor_accel and sensor_gyro are now always raw sensor data
- calibration procedures no longer need to first clear existing values before starting
- temperature calibration (TC) remove all scale (SCL) parameters
- gyro and baro scale are completely unused
- regular accel calibration scale can be used (CAL_ACC*_xSCALE) instead of TC scale
- create common uORB::PublicationBase
- uORB::PublicationQueued types are now type aliases
- ORB_PRIO use enum type everywhere to avoid accidental misuse
- PX4Accelerometer/PX4Gyroscope/etc driver libs explicitly advertise on construction, unadvertise on destruction. This is a workaround for any potential issues that might appear when accel/gyro cdev and uORB indexing doesn't align.
The bulk of this change was tightly coupled and needed to be deleted in one pass. Some of the smaller changes were things that broke as a result of the initial purge and subsequently fixed by further eradicating unnecessary platform differences. Finally, I deleted any dead code I came across in the related files I touched while going through everything.
- DriverFramework (src/lib/DriverFramework submodule) completely removed
- added dspal submodule in qurt platform (was brought in via DriverFramework)
- all df wrapper drivers removed
- all boards using df wrapper drivers updated to use in tree equivalents
- unused empty arch/board.h on posix and qurt removed
- unused IOCTLs removed (pub block, priv, etc)
- Integrator delete methods only used from df wrapper drivers
- commander: sensor calibration use "NuttX version" everywhere for now
- sensors: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- battery_status: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- cdev cleanup conflicting typedefs and names with actual OS (pollevent_t, etc)
- load_mon and top remove from linux boards (unused)
- delete unused PX4_MAIN_FUNCTION
- delete unused getreg32 macro
- delete unused SIOCDEVPRIVATE define
- named each platform tasks consistently
- posix list_devices and list_topics removed (list_files now shows all virtual files)
Marco Hauswirth