Also containst a mini refactor by removing the unnecessary function
get_default_altitude_acceptance_radius().
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
When a mission starts capturing images using the
MAV_CMD_IMAGE_START_CAPTURE command, it should also stop it again, in
case it is stopped early, e.g. with RTL.
Such that the loiter (orbit) status can be displayed on groundstation
and the WP is accepted once within loiter radius
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
If the current yaw setpoint is valid we should use it to make the transition in this direction.
For a VTOL_TAKEOFF the yaw_setpoint is used to specify the transition direction (the
vehicle is aligned towards it and then transition is started). The current yaw can be
a bit off (e.g. because MIS_YAW_ERR is large), and it is better to track the actual setpoint.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This feature allows user to use a Gripper type pacakge delivery
mechanism on a drone to trigger the delivery during a mission via the
mission item `DO_GRIPPER`.
This is a minimal change that is intended to have simplest pacakge
delivery feature on PX4, however the future scope would extend this
feature out of Navigator, and rather move towards a federated PX4
(flight-mode flexibility) architecture. But until then, this will serve
the purpose.
Update Tools/sitl_gazebo submodule to remove sdf file overwrite error
- There was an error happening due to .sdf file being overwritten, it
was caused by a wrongfully added. sdf file.
- This update pulls in the PR commit: https://github.com/Auterion/sitl_gazebo/pull/147
Initial cut on supporing PAYLOAD_PLACE mission item
Tidy and comment on navigation.h to clarify mission item definition
- Convert vehicle command ack subscription data type to
SubscriptionData, to not care about having a dedicated struct for
copying the latest data
- Tidy and comment on navigation.h to clarify the definition of
mission_item_s, which is confusing as it is an intergration of MAVLink
Standard into PX4's internal Mission Item structure
Rename mission_block's mission item reached function & cleanup navigator
- Isolated Handle Vehicle Commands function inside the Navigator
- Rename mission_block's mission item reached function to 'reached or
completed', as the navigation command can also be an action (e.g.
DO_SET_SERVO, which doesn't make sense to refer to as 'reached' when we
have successfully done executed the command)
Include MAVLink PR commit to include payload_drop message
More changes to add payload_drop MAVLink message support
- Comitting for testing purposes
Add mission item payload_drop to vehicle command payload drop link
- Now with a mission item with the nav_cmd set to 'payload drop', the
appropriate 'payload drop' vehicle command will be issued
Make Payload drop executable via Mission Plan
Implement payload_drop module to simulate payload delivery
- Simple module that acknowledges the payload drop vehicle command after
certain time, to simulate a successful delivery
Additional changes - payload drop module not working yet
- Need to do more thread stuff to make it work :(
Fix Payload Drop enum mismatch in vehicle_command enums
- First functional Payload Drop Implementation MVP
- Simple Ack & resuming mission from Navigator tested successfully
Hold the position while executing payload drop mission item
- Still the position hold is not solid, maybe I am missing something in
the position setpoint part and all the internal implications of
Navigator :(
Add DO_WINCH command support
Some fixes after rebase on develop branch
- Some missed brackets
- Some comment edits, etc
Add DO_WINCH command support
- Still has a problem of flying away from the waypoint while the
DO_WINCH is being executed, probably position setpoint related stuff :(
Apply braking of the vehicle for DO_WINCH command
- Copies the behavior of NAV_CMD_DELAY, which executes a smooth, braking
behavior when executing the delay because of the braking condition in
`set_mission_items` function
- This will not apply to Fixed wings
- The payload deploy getting triggered may be too early, as right now as
soon as the vehicle approaches the waypoint within the acceptance
threshold, the payload gets deployed
Add DO_GRIPPER support
Implement Gripper actual Hardware triggering support
- Currently not working, possibly in the mixer there's a bug
- Implemented the publishing of actuator_controls_1 uORB topic
- Implemented the test command for the payload_drop module, to test the
grpiper functionality
- Edited px4board file to include the payload_drop module
- Added Holybro X500 V2 airframe file, to enable testing on X500 V2
- Created new Quad X Payload Delivery mixer, which maps the actuator
controls 1 topic's data into the MAIN pin 5 output
Make Payload Drop Gripper Work
- Initialization of the Gripper position to CLOSED on Constructor of the
payload_drop module
- Setting the OPEN and CLOSED value to the appropriate actuator controls
input
Set vehicle_command_ack message's timestamp correctly
- By not setting the timestamp, the ack commands were not correctly
graphed in PlotJuggler!
Rename payload drop module to payload deliverer
- I think it's a more complex name (harder to type), but more generic
Add Gripper class (WIP)
Add Gripper class functionalities
- Add gripper uORB message
- Add gripper state machine
Use Gripper class as main interface in payload_deliverer
- Utilizes Gripper class functions for doing Gripper functionality
Remove mixer based package delivery trigger logic
- Remove custom mixer files that mapped actuator controls to outputs
statically
Additional improvements of the payload_deliverer
Fix payload_deliverer module not starting
- _task_id wasn't geting set appropriately in task_spawn function, which
led to runtime failure
Add Gripper Function to mixer_module
- Still not showing up as function mapping in QGC, needs fix
Add parameters to control gripper behavior
- Now user can enable / disable gripper
- Also select which type of gripper to use
Applying review from nuno
Remove timeout fetching from mission item and use gripper's timeout
- Previously, it was planned to use a custom DO_GRIPPER and DO_WINCH
MAVLink message definitions with information on timeout, but since now
we are using original message definition, only relevant timeout
information is defined in the payload_deliverer class
- This change brings in the timeout parameter to the Navigator, which
then sets the timeout in the mission_block class level, which then
processes the timeout logic
Make payload deployment work for Allmend test :P
Support gripper open/close test commands in payload_deliverer
Move enum definition for GRIPPER_ACTION to vehicle_command.msg
Remove double call for ` ${R}etc/init.d/rc.vehicle_setup`
- Was introduced during the rebase
- Was causing module already running & uORB topic can't be advertised
errors
Fix format via `make format` command
Modify S500 airframe file to use for control allocation usage
- Added Control allocation related parameters as default to not have it
reset every time the airframe is selected
Implement mission specific payload deploy timeout and more changes
Switch payload_deliverer to run on work queue
Remove unnecessary files
- Airframe changes from enabling control allocation are removed
Address review comments
- Remove debug messages
- Remove unnecessary or verbose comments & code
- Properly call parameter_update() function
Switch payload_deliverer to scheduled interval work item & refactor
- Switch to Schedeuled on Interval Work Item, as previous vehicle
command subscription callback based behavior led to vehicle comamnd ack
not being sent accordingly (since the Run() wouldn't be called unless
there's a new vehicle command), leading to ack command not being sent
out
- Also, old vehicle commands were getting fetched due to the
subscription callback as well, which was removed with this patch
- Fix the wrong population of floating point param2 field of vehicle
command by int8_t type gripper action by creating dedicated function
- Refactor and add comments to increase readability
Add gripper::grabbing() method and handle this in parameter update
- Previously, the intermediate state 'grabbing' was not considered, and
when the parameter update was called after the first initialization of
the gripper, the grab() function was being called again, which would
produce unnecessary duplicate vehicle command.
- Also replaced direct .grab() access to sending vehicle comamnd, which
unifies the gripper actuation mechanism through vehicle commands.
Navigator: Change SubscriptionData to Subscription to reduce memory usage
- Also removed unused vehicle command ack sub
PayloadDeliverer: Remove unnecessary changes & Bring back vehicle_command sub cb
rtl state was getting reset on inactive, which meant that the state which triggered resuming e.g. mission landing would be overwritten, and the navigator mode would switch back and forth between rtl and mission. this commit:
1. moves the reset of rtl state to the on activation function (removing it from the on inactive function)
2. functionalizes the rtl state input to the rtl time estimator so that rtl time can still be calculated from state=none while inactive
- landing slope/curve library removed
- flare curve removed (the position setpoints will not be tracked during a flare, and were being ignored by open-loop maneuvers anyway)
- flare curve replaced by simply commanding a constant glide slope to the ground from the approach entrance, and commanding a sink rate once below flaring alt
- flare is now time-to-touchdown -based to account for differing descent rates (e.g. due to wind)
- flare pitch limits and height rate commands are ramped in from the previous iteration's values at flare onset to avoid jumpy commands
- TECS controls all aspects of the auto landing airspeed and altitude/height rate, and is only constrained by pitch and throttle limits (lessening unintuitive open loop manuever overrides)
- throttle is killed on flare
- flare is the singular point of no return during landing
- lateral manual nudging of the touchdown point is configurable via parameter, allowing the operator to nudge (via remote) either the touchdown point itself (adjusting approach vector) or shifting the entire approach path to the left or right. this helps when GCS map or GNSS uncertainties set the aircraft on a slightly offset approach"
- post takeoff, the aircraft follows the infinite line sourced from the launch point in the direction of the takeoff waypoint
- takeoff waypoint altitude is used as a clearance altitude, set such that once above, the aircraft has cleared all ground occlusions and may proceed with the mission
- runway takeoff state machine simplified to throttle ramp, clamped to runway, climbout, and fly
- throttle ramp must complete before switching to next state to avoid a jump in throttle setpoint just after takeoff if the takeoff airspeed is reached before the ramp is complete
- roll constraints near ground post takeoff removed from runway takeoff class (handled externally now)
- minimum airspeed in TECS is reduced to takeoff speed (if necessary) to lower the underspeed detection bound
- lateral-directional guidance uses a different period parameter during ground roll
- trim throttle is handled entirely by the position controller
- navigator should use speed setpoints
- added flag gliding_enabled in position setpoint to stills support gliding
Signed-off-by: RomanBapst <bapstroman@gmail.com>
- As it is always only used for the vehicle command ack message
- It was a duplicate, hence making it error prone for maintainment
- The uORB message comments were updated to make the relationship with
the MAVLink message / enum definitions clear
rename follow_me_status to follow_target_status
enable follow_target_estimator on skynode
implement the responsiveness parameter:
The responsiveness parameter should behave similarly to the previous
follow-me implementation in navigator. The difference here is that
there are now two separate gains for position and velocity fusion.
The previous implemenation in navigator had no velocity fusion.
Allow follow-me to be flown without RC
SITL tests for follow-me flight task
This includes:
- Testing the setting for the follow-me angle
- Testing that streaming position only or position
and velocity measurements both work
- Testing that RC override works
Most of these tests are done with a simulated model
of a point object that moves on a straight line. So
nothing too spectacular. But it makes the test checks
much easier.
Since the estimator for the target actually checks new
measurements and compares them to old ones, I also added
random gausian noise to the measurements with a fixed seed
for deterministic randomness. So repeated runs produce
exactly the same results over and over.
Half of the angles are still missing in MAVSDK. Need to create
an upstream PR to add center left/right and rear left/right options.
These and the corresponding SITL tests need to be implemented
later.
sitl: Increase position tolerance during follow-me
Astro seems to barely exceed the current tolerance (4.3 !< 4.0)
causing CI to fail. The point of the CI test is not to check
the accuracy of the flight behaviour, but only the fact that the
drone is doing the expected thing. So the exact value of this
tolerance is not really important.
follow-me: gimbal control in follow-me
follow-me: create sub-routines in flight task class
follow-me: use ground-dist for emergency ascent
dist_bottom is only defined when a ground facing distance sensor exist.
It's therefore better to use dist_ground instead, which has the distance
to the home altitude if no distance sensor is available.
As a consequence it will only be possible to use follow-me in a valley
when the drone has a distance sensor.
follow-me: point gimbal to the ground in 2D mode
follow-me: another fuzzy msg handling for the estimator
follow-me: bugfix in acceleration saturation limit
follow-me: parameter for filter delay compensation
mantis: dont use flow for terrain estimation
follow-me: default responsiveness 0.5 -> 0.1
0.5 is way too jerky in real and simulated tests.
flight_task: clarify comments for bottom distance
follow-me: minor comment improvement
follow-me: [debug] log emergency_ascent
follow-me: [debug] log gimbal pitch
follow-me: [debug] status values for follow-me estimator
follow-me: setting for gimbal tracking mode
follow-me: release gimbal control at destruction
mavsdk: cosmetics 💄
The flight termination action on geofence violation is described as only trigger, when the corresponding circuit breaker is not disabled. However, the description of the circuit breaker states, that the geofence action is not depedning on this circuit breaker. The implementation follows the description of the circuit breaker. Hence the GF_ACTION description is adapted.
This is to make clear that the relevant part of the home position
message for navigator is the global one. Local home position isn't
required as everything is done in global coordinates.
The specific home_alt_valid is used when lat/lon are not used
For many VTOLs/fixed-wing drones a 50m loiter radius is too tight, and
going to 80m is a better and safer default.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Silvan Fuhrer