- remove deprecated actuator_controls[INDEX_FLAPS/SPOILERS/AIRBRAKES]
- use new topic normalized_unsigned_setpoint.msg (with instances flaps_setpoint
and spoilers_setpoint) to pass into control allocation
- remove flaps/spoiler related fields from attitude_setpoint topic
- CA: add possibility to map flaps/spoilers to any control surface
- move flaps/spoiler pitch trimming to CA (previously called DTRIM_FLAPS/SPOILER)
- move manual flaps/spoiler handling from rate to attitude controller
FW Position controller: change how negative switch readings are intepreted
for flaps/spoilers (considered negative as 0).
VTOL: Rework spoiler publishing in hover
- pushlish spoiler_setpoint.msg in the VTOL module if in hover
- also set spoilers to land configuration if in Descend mode
Allocation: add slew rate limit of 0.5 to flaps/spoilers configuration change
Instead of doing the flaps/spoilers slew rate limiting in the FW Position Controller
(which then only is applied in Auto flight), do it consistently over all flight
modes, so also for manual modes.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* Fixedwing rate control into a separate module
* Start fw_rate_control for vtol
* Move over airspeed related parameters to fw_rate_control
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
Completely detach the steering wheel logic from the yaw controller (beside using the
same manual stick input in a manual flight mode).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- vehicle_angular_velocity and vehicle_angular_acceleration are produced together from the same input data, consumed together, and share the the same metadata (timestamps)
- individually these topics each have 16 bytes of metadata (2 timestamps) for 12 bytes of data (x,y,z float32)
- remove separate flaperon controls input to mixer instead enable spoiler support
- add slew rate limiting on both flap and spoiler controls
- add spoiler configuration for Landing and Descend
- add trimming from spoiler deflection
- FW Attitude control: remove FW_FLAPS_SCL param -->
The flap settings for takeoff and landing are now specified relative to full range.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- parameter updates can be quite expensive because they trigger nearly all modules to reload all of their parameters immediately
- limit modules from updating faster than once per second
- ecl/attitude_fw was never maintained as a standalone library
- moving ecl/attitude_fw library into the fw_att_control module to ease further development
* FW attitude controller, FW position controller and VTOL attitude controller subscribe to airspeed_validated topic
* add possibility to switch off the airspeed valid checks
* remove airspeed valid checks from commander
* clean up of VTOL transition logic
* Airspeed Selector: remove dynamic allocation of airspeed validators (depending on number of connected sensors) but do it statically for the maximum number allowed. Check for number of connected sensors not only during start up, but always when vehicle is disarmed.
* Airspeed Selector: change work queue from lp to att_pos_ctrl as this module is safety-critical
* add airspeed selector to px4_fmu-v2 defaults
and remove the px4_ prefix, except for px4_config.h.
command to update includes:
for k in app.h atomic.h cli.h console_buffer.h defines.h getopt.h i2c.h init.h log.h micro_hal.h module.h module_params.h param.h param_macros.h posix.h sem.h sem.hpp shmem.h shutdown.h tasks.h time.h workqueue.h; do for i in $(grep -rl 'include <px4_'$k src platforms boards); do sed -i 's/#include <px4_'$k'/#include <px4_platform_common\/'$k/ $i; done; done
for in $(grep -rl 'include <px4_config.h' src platforms boards); do sed -i 's/#include <px4_config.h/#include <px4_platform_common\/px4_config.h'/ $i; done
Transitional headers for submodules are added (px4_{defines,log,time}.h)
* adds a work_queue systemcmd that will bring a tree view of all active work queues and work items
* WorkQueues now track attached WorkItems and will shutdown when the last WorkItem is detached
Script to update include paths:
for i in $(grep -rl 'include <px4_work_queue' src platforms); do sed -i 's/#include <px4_work_queue/#include <px4_platform_common\/px4_work_queue/' $i; done
* VTOL trans: changed that now in transition for both MC and FW the corresponding (correct) attitude controller is running
* attitude setpoint for stabilized mode is generated by tailsitter.cpp
* reset yaw setpoint during transition to avoid big yaw errors after
transition back to hover
* VT_TYPE parameter: added "reboot required" metadata
Silvan Fuhrer