bbfaa4694c
boards: cleanup serial RX DMA hrt_call_every
...
- remove ts_to_abstime dependency
2021-10-06 14:39:59 -04:00
c271a9e3e6
add sd_stress to all boards and run on test rack
2021-10-04 17:38:31 -04:00
6d78054f50
mavlink USB auto start/stop on boards with VBUS
...
- no longer start sercon or mavlink usb by default
- on USB connection (VBUS) monitor serial USB at low rate and start Mavlink if there's a HEARTBEAT or nshterm on 3 consecutive carriage returns
- the mavlink USB instance is automatically stopped and serdis executed if USB is disconnected
- skipping Mavlink USB (and sercon) saves a considerable amount of memory on older boards
2021-10-03 15:32:54 -04:00
1443f773da
mbe: add module to targets
2021-10-02 21:25:21 -04:00
5874b1f87c
mc atune: add module to all targets
...
- adjust flash constrianed targets to fit
2021-10-02 18:12:05 -04:00
c67d943158
boards: mro_ctrl-zero-h7-oem board.h fix SPI5 ( #18294 )
...
- fix spi pin missmatch PF9=GPIO_SPI5_MOSI_2
2021-09-25 20:05:18 -04:00
c5c80e31b6
boards: remove DIRECT_INPUT_TIMER_CHANNELS from board_config.h
2021-09-08 16:10:24 -04:00
a8e75d174c
boards: remove BOARD_HAS_PWM and use DIRECT_PWM_OUTPUT_CHANNELS
2021-09-08 16:10:24 -04:00
40e5477edb
NuttX boards fix mkfatfs and rcS logic
2021-09-01 15:16:00 -04:00
965f11e923
MRO: Set up MPU after boot to app
...
This is needed in case the bootloader configured the MPU, which could interfere with the app as the bootloader memory map / configuration is different.
2021-09-01 08:53:05 +02:00
bb913ae11a
system_load:Track Dynamic PID hash
2021-08-13 14:22:00 -04:00
defbb0e17a
mro_ctrl-zero-f7-oem: Update nsh defconfig NuttX 10.1.0+
2021-08-13 14:22:00 -04:00
47f1b934d3
mro_x21: Update nsh defconfig NuttX 10.1.0+
2021-08-13 14:22:00 -04:00
0823bb5584
mro_x21-777: Update nsh defconfig NuttX 10.1.0+
2021-08-13 14:22:00 -04:00
f527286200
mro_ctrl-zero-h7-oem: Update bootloader defconfig NuttX 10.1.0+
2021-08-13 14:22:00 -04:00
5446d4bde8
mro_ctrl-zero-h7-oem: Update nsh defconfig NuttX 10.1.0+
2021-08-13 14:22:00 -04:00
e96c3e5093
mro_pixracerpro: Update bootloader defconfig NuttX 10.1.0+
2021-08-13 14:22:00 -04:00
1d789863b4
mro_pixracerpro: Update nsh defconfig NuttX 10.1.0+
2021-08-13 14:22:00 -04:00
fe8c902f90
mro_ctrl-zero-f7: Update nsh defconfig NuttX 10.1.0+
2021-08-13 14:22:00 -04:00
49c85e7713
mro_ctrl-zero-h7: Update bootloader defconfig NuttX 10.1.0+
2021-08-13 14:22:00 -04:00
0d47f1a3cb
mro_ctrl-zero-h7: Update nsh defconfig NuttX 10.1.0+
2021-08-13 14:22:00 -04:00
ec61512cdf
NuttX inits null console
2021-08-13 14:22:00 -04:00
0e1f3a2d62
px4_add_board: infer VENDOR, MODEL & LABEL from cmake file name
2021-08-03 10:36:25 +02:00
e9f84ba708
keep minimal legacy battery parameters for older QGC usability
...
- BAT_V_EMPTY, BAT_V_CHARGED, BAT_V_LOAD_DROP, BAT_N_CELLS
2021-07-23 15:07:53 -04:00
6b356068cb
boards: mro_x21-777 board.h fix SPI 2 SCK pin
...
- SPI 2 had the wrong SCK PIN -> PB10 instead of PB13 -> accidentally the kill pin
could be probably wrong on other mro boards
2021-06-23 15:00:20 -04:00
05bdef867d
Track NuttX syslog change
2021-06-16 17:07:47 +02:00
6bc09138c1
Adding BatMon smart battery as a module and refactoring SMBUS based SBS 1.1 spec to a library
2021-06-09 12:17:45 -04:00
5f775b508f
boards: enable CONFIG_OTG_ID_GPIO_DISABLE on all F7/H7
2021-06-01 15:19:15 -04:00
32e92ba817
Revert:Pull downs - bad levels cause motor spins
2021-06-01 15:18:47 -04:00
071eaef884
Adjust paths to bootloader include files for boards
...
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae >
2021-05-26 12:57:37 -07:00
c3884b5bc1
fake_imu (formally fake_gyro) updates for testing gyro filtering
...
- fake_imu now publishes sine sweeps over 10 seconds
- accel is also published so that fake IMU can be selected when the only option
2021-05-17 20:26:25 -04:00
3f5a0e49a4
mro_pixracerpro: Initalize PWM as input with Pull Downs
2021-05-05 20:48:06 +02:00
86360d076c
mro_ctrl-zero-h7: Initalize PWM as input with Pull Downs
2021-05-05 20:48:06 +02:00
3820f761b1
mro_ctrl-zero-h7-oem: Initalize PWM as input with Pull Downs
2021-05-05 20:48:06 +02:00
50d3af1ba1
mro_ctrl-zero-f7: Initalize PWM as input with Pull Downs
2021-05-05 20:48:06 +02:00
867aa9d4bc
mro_ctrl-zero-f7-oem: Initalize PWM as input with Pull Downs
2021-05-05 20:48:06 +02:00
64688b04d8
boards: mro pixracerpro set BOARD_SUPPORTS_RC_SERIAL_PORT_OUTPUT instead of RC_SERIAL_SINGLEWIRE
2021-04-29 21:06:39 -04:00
58b40fbbb9
boards: move testing to dedicated test variants
2021-04-14 09:21:31 +02:00
ad934b4911
icm20948 i2c passthrough driver for ak09916 magnetometer (Here+ GPS/compass)
...
- include icm20948 on most boards by default
- create more test variants for default boards near flash limit (cuav_nora_test, cuav_x7pro_test, holybro_durandal-v1_test)
2021-04-04 21:18:16 -04:00
bbf27d6960
boards: mro pixracerpro Add remaining SRAM4 & DTCM to heap
2021-04-03 14:13:23 -04:00
961bac759a
mro pixracerpro:Add remaining SRAM4 & DTCM to heap
2021-04-03 14:13:23 -04:00
2f9a57c604
mro ctrl-zero-h7:Add remaining SRAM4 & DTCM to heap
2021-04-03 14:13:23 -04:00
5c7a9204a2
mro ctrl-zero-h7-oem:Add remaining SRAM4 & DTCM to heap
2021-04-03 14:13:23 -04:00
6874e9fba0
boards: NuttX disable all NSH memory debug commands (mb, mh, mw) by default
...
- closes https://github.com/PX4/PX4-Autopilot/issues/17062
2021-03-30 09:23:43 -04:00
631d1647d3
boards: minimize unnecessary differences in default variants
2021-03-28 14:46:47 -04:00
f65781025e
boards: mRo x21 enable mpu9250 mag (only internal)
...
- fixes #17244
2021-03-26 21:02:30 -04:00
e77bffe582
boards: STM32H7 remove CONFIG_MM_REGIONS=3
2021-03-26 17:40:44 -04:00
bbdb671dd2
mro pixracerpro:Properly configure BDMA
2021-03-23 05:52:27 -07:00
a8ece584e5
mro ctrl-zero-h7-oem:Properly configure BDMA
2021-03-23 05:52:27 -07:00
344be233cf
mro ctrl-zero-h7:Properly configure BDMA
2021-03-23 05:52:27 -07:00
Daniel Agar