This param has no effect within the Firmware.
The param can be used for example:
* in log post processing to have context about the flight
* in ground stations to adapt the UI automatically
outside the fence" to "engage geofence failsafe on transition". This
way, the pilot is not stucked in the non flight zone and can switch to
a manual mode and fly back or trigger RTL.
This commit adds Roll Pitch Yawrate Thrust (RPYrT) setpoint control to the
PX4 stack, enabling the UAV to follow specific yawrates sent from
offboard. It also introduces individual body_rate flags, along the
lines of mavros.
Tested on a MoCap enabled flight arena in KTH Royal Institute of
Technology, Stockholm. The MAV receives RPYrT setpoints from an
external PID controller to stabilize around position setpoints.
The UAV is also externally disturbed to assess the stability to
external unmodeled events.
Fixed Kabir comments.
Removed deprecated ignore_bodyrate.
Fixed integration test.
This changes the enums used for various VTOL states to enum classes
which makes them type-safe and should avoid shadowing.
This change was motivated by a Clang warning about shadowing of the
enum const TRANSITION_TO_FW which was declared twice, once in
vtol_type.h and once in standard.h.
This change only removes the shadowing but presumably these enums could
be cleaned up and consolidated further.
This moves the hysteresis test out of the systemlib and makes it its own
small library. Since it still depends on hrt_absolute_time this does not
link yet. My attempt to get all link dependencies together failed.
But fix the two crucial problems:
- When to begin the ramp?
There's a calculation now for the velocity ramp initial value
such that the resulting thrust is zero at the beginning.
- When to end the ramp?
The ramp is applied to the upwards velocity constraint and it
just ramps from the initial value to the velocity constraint
which is applied during flight. Slower/going down is always possible.
Without always updating the takeoff state it will not get skipped when
the takeoff happened manually and when you switch from manual to position
mode the drone goes to idle and falls.
There are two local_position_setpoint in the position controller.
One describing the setpoint the task gives to the position controller
and a second one with the output of the position controller. I corrected
the wrong one during takeoff because the new takeoff thrust ramp runs after
the controller and not before.
The velocity ramp had problems with:
- different vehicle tunings resulted in the start value of the resulting
thrust ramp staring either higher and lower than zero thrust.
lower -> delay of beginning
higher -> small jump at beginning
- when a task set position and velocity at the same time during takeoff
(which AutoSmoothVel does) it resulted in a velocity setpoint
jump at the end of the ramp because the additional velocity
setpoint correction from the position controller was not considered.
The thrust ramp should now be very deterministic:
- always start at zero
- always end at the curreant thrust setpoint output
of the complete position controller
The initial idea of the flight task architecture was that
a task can freely set it's setpoints and doesn't have to
worry about takeoff and landing. It would just takeoff
when it's landed and there's a setpoint to go up and
land when it puts a setpoint that pushes into the ground.
With the takeoff logic there are some significant interface
problems depending on the way a task is implemented:
From the setpoint is not high enough to trigger to
an unexpected takeoff because of some estimator
fluctuation affecting the setpoint. It's easiest to solve this
by allowing the task to determine when a takeoff is triggered.
If no condition is implemented by default a task is not
allowing a takeoff and cannot be used to get the vehicle
off the ground.
After boot the user is in manual mode and if he has an RC
but doesn't switch out the thrust gets set to the throttle stick
position. When he then starts a takeoff from tablet the thrust is still
high while arming and the land detector immediately sees a takeoff
skiping smooth takeoff from the position controller.
- start from a velocity setpoint pushing into the ground
to ramp from idle thrust up.
- start with a bit higher velocity setpoint threshold to make
sure the vehicle has a chance to really get off the ground.
- calculate ramp slope from initialization setpoint to the desired one
instead from zero to the desired. this ramps up quicker when you demand
a very small upwards velocity like the AutoLineSmoothVel and
ManualPositionSmoothVel tasks do at the beginning.
- don't stay in the takeoff ramp depending on the land detector, this
is unnecessary.
bresch