internal PX4IO safety_off state is removed and replaced with a normal safety button event. From this 'commit' commander is taking care of the PX4IO safety.
internal PX4IO safety_off state is removed and replaced with a normal safety button event. From this 'commit' commander is taking care of the PX4IO safety.
- fixes the deadlock in px4io ioctl mixer reset
- px4io Run() locks (CDev semaphore)
- mixer load goes through px4io ioctl MIXERIOCRESET which calls MixingOutput::resetMixerThreadSafe()
- MixingOutput::resetMixerThreadSafe() stores a Command::Type::resetMixer command in an atomic variable, schedules a work queue cycle, then sleep spins until the command is cleared
- the execution of the cycle eventually calls back into PX4IO::updateOutputs(), which tries to lock (and waits forever)
- uavcan firmware server no longer shuts down when arming (nodes might restart in flight)
- always handle UAVCAN parameters with or without the FW server active
- remove legacy ESC enumeration in FW server
Forwards messages on the gps_inject_data uORB topic as
uavcan::equipment::gnss::RTCMStream messages on the UAVCAN bus. This
enables differential/RTK GPS over UAVCAN to work.
Tested with CubePilot Cube Orange, Here+ base and Here3 rover.
Signed-off-by: Alex Mikhalev <alexmikhalevalex@gmail.com>
The bulk of this change was tightly coupled and needed to be deleted in one pass. Some of the smaller changes were things that broke as a result of the initial purge and subsequently fixed by further eradicating unnecessary platform differences. Finally, I deleted any dead code I came across in the related files I touched while going through everything.
- DriverFramework (src/lib/DriverFramework submodule) completely removed
- added dspal submodule in qurt platform (was brought in via DriverFramework)
- all df wrapper drivers removed
- all boards using df wrapper drivers updated to use in tree equivalents
- unused empty arch/board.h on posix and qurt removed
- unused IOCTLs removed (pub block, priv, etc)
- Integrator delete methods only used from df wrapper drivers
- commander: sensor calibration use "NuttX version" everywhere for now
- sensors: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- battery_status: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- cdev cleanup conflicting typedefs and names with actual OS (pollevent_t, etc)
- load_mon and top remove from linux boards (unused)
- delete unused PX4_MAIN_FUNCTION
- delete unused getreg32 macro
- delete unused SIOCDEVPRIVATE define
- named each platform tasks consistently
- posix list_devices and list_topics removed (list_files now shows all virtual files)
Main UAVCAN protocol handling and ESC updates run on the same thread/wq as
before. There are 2 WorkItems for separate scheduling of the 2, so that
ESC updates run in sync with actuator_control updates. UAVCAN is scheduled
at a fixed rate of 3ms (previously the poll timeout) and on each UAVCAN
bus event.
This leads to roughly the same behavior as before. CPU & RAM usage are
pretty much the same (tested on Pixhawk 4).
Testing done: Motors still work (with feedback), param changes and a
UAVCAN optical flow sensor.
and remove the px4_ prefix, except for px4_config.h.
command to update includes:
for k in app.h atomic.h cli.h console_buffer.h defines.h getopt.h i2c.h init.h log.h micro_hal.h module.h module_params.h param.h param_macros.h posix.h sem.h sem.hpp shmem.h shutdown.h tasks.h time.h workqueue.h; do for i in $(grep -rl 'include <px4_'$k src platforms boards); do sed -i 's/#include <px4_'$k'/#include <px4_platform_common\/'$k/ $i; done; done
for in $(grep -rl 'include <px4_config.h' src platforms boards); do sed -i 's/#include <px4_config.h/#include <px4_platform_common\/px4_config.h'/ $i; done
Transitional headers for submodules are added (px4_{defines,log,time}.h)
- move most orb to uORB::Publication and uORB::Subscription
- update legacy message handling (warn to PX4_INFO, PX4_WARN, PX4_ERR)
- add perf counters
- sensors/mag support newer `uavcan::equipment::ahrs::MagneticFieldStrength2` message
- sensors/gps support `uavcan::equipment::gnss::Auxiliary` for hdop and vdop
- sensors delete obsolete ioctl and read methods
- use PublicationMulti for actuator_outputs and esc_reports (to coexist with other output modules)
- add GNSS parameter metadata (parameters_injected.xml)
Igor Mišić