c6803166d1
boards: cubeorange: fix dma map label ( #23953 )
2024-11-15 21:17:43 -05:00
51702efe94
boards: update all NuttX defconfigs
2024-10-02 15:08:38 -04:00
2d99ae18ad
stm32h7: Reset USART clock selection ( #23498 )
...
This resets the USARTs' clock source selection to the default, in case
it has been changed by the bootloader.
This is required if booting from the ArduPilot bootloader which happens
to reset the clock selection to PLL.
Without this fix, UARTs (including the console) is garbled, so
presumably at an invalid baudrate.
2024-08-07 11:41:50 -04:00
20137bea40
boards: add console build for Cube Orange(+)
...
This adds a build variant which enables the serial console, and
therefore disables the ADSB receiver.
2024-07-10 21:14:08 -04:00
543454f12e
stm32h7:ADC STM32_RCC_D3CCIPR_ADCSEL->STM32_RCC_D3CCIPR_ADCSRC
2024-01-30 18:07:57 -05:00
563fd8427a
boards: increase init stack size by 100B
...
Signed-off-by: Silvan Fuhrer <silvan@auterion.com >
2023-10-02 09:37:06 +02:00
c1dbe177b8
boards: move FRAM emulated sector size to the 32-byte granularity ( #21204 )
2023-09-20 16:50:36 -04:00
c95539e8ce
boards: increase init stack size by 150B
...
External airframes need a bit more stack due to nested configs.
2023-06-09 21:11:11 -04:00
635daeed8a
NuttX push jlink-nuttx into cmake and enable CONFIG_DEBUG_TCBINFO by default
2023-01-12 09:05:26 -05:00
dc5ce9b0ce
boards: NuttX increase default CONFIG_ARCH_INTERRUPTSTACK 512->768 bytes
...
- during casual testing on default configs the stack was penetration was reaching ~90% which is a bit too close for comfort
- increasing by 50% to be conservative
2023-01-07 12:07:35 -05:00
0fbb6db6d4
boards: update all NuttX defconfig (make all_olddefconfig)
2022-12-29 12:50:37 -05:00
2cb4ef0629
NuttX 10.3+ upgrade ( #20190 )
...
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com >
Co-authored-by: David Sidrane <David.Sidrane@NscDg.com >
Co-authored-by: alexklimaj <alex@arkelectron.com >
2022-11-20 20:28:07 -05:00
5b6e5a0968
boards: NuttX update all boards to preallocated sem holder list
...
- CONFIG_SEM_PREALLOCHOLDERS=32
- CONFIG_SEM_NNESTPRIO=16 (default)
2022-05-31 01:41:07 -07:00
132a07f53c
boards: test boards add NuttX ostest and run on Jenkins test rack
2022-05-29 13:41:16 -04:00
fd81951391
boards: STM32H7 pad to 256 bit - 32 bytes ( #19724 )
2022-05-27 14:04:51 -04:00
9686c81f7d
boards: enable flow control on CDCACM
...
This enables flow control on CDCACM for the NuttX boards which fixes a
problem where HITL would stall.
The stall could happen if the hardware would be a bit too slow in
keeping up with the incoming messages. Often, this happened on arming
because the logger would take some time to log all parameters right at
the beginning.
The stall would then not recover due to NuttX bug where the rx interrupt
would not be restored correctly and instead only a slower watchdog would
release the next read. This watchdog takes 200ms which means it's hard
to impossible to get out of the situation without restarting sim and/or
PX4. For more information about the issue, see:
apache/incubator-nuttx#3633
As a workaround, until that bug is fixed, and because it makes sense
anyway, I propose to enable FLOWCONTROL for the serial via USB.
2021-12-21 08:01:38 +01:00
37c1598f38
boards: cubepilot_cubeorange enable calib_udelay and run on test rack
2021-12-05 14:50:03 -05:00
7d515e3d58
boards: cubepilot_cubeorange lower cpu clock 480 -> 400 MHz to reduce temperature
2021-12-05 14:50:03 -05:00
a2064cceff
boards: enable early MPU reset on any board potentially not using the PX4 bootloader
2021-12-01 20:13:41 -05:00
c82e0e0531
cubepilot_cubeorange test:Remove CONFIG_RAMTRON_WRITEWAIT
2021-11-26 19:27:29 -05:00
6e1500a7de
cubepilot_cubeorange nsh:Remove CONFIG_RAMTRON_WRITEWAIT
2021-11-26 19:27:29 -05:00
e34aacd520
cubepilot_cubeorange:Set CONFIG_MKFATFS_BUFFER_ALIGMENT=32
2021-11-24 09:46:23 -05:00
f5d9b01f5c
NuttX build in place
...
- cmake NuttX build wrapper compile in place instead of copying source tree to build directory
- slightly faster skipping necessary copying (depending on system)
- allows debugging in place
- easier to work directly in NuttX following official documentation
- simplifies overall build which should make it easier to resolve any remaining NuttX dependency issues in the build system
- the downside is switching back and forth between different builds always require rebuilding NuttX, but I think this is worth the improved developer experience
- also no longer builds px4io and bootloader in every single build, for most users these rarely change and we're wasting a lot of build time
2021-11-15 18:47:38 -05:00
a8c3bcca32
boards: disable CONFIG_STM32H7_SPI_DMATHRESHOLD
2021-11-08 19:20:47 -05:00
38e2e6a01f
Use NuttX MPU Reset ( #18283 )
...
* NuttX with MPU reset backports
* Use NuttX MPU reset
2021-10-25 18:05:31 -04:00
40e5477edb
NuttX boards fix mkfatfs and rcS logic
2021-09-01 15:16:00 -04:00
bb913ae11a
system_load:Track Dynamic PID hash
2021-08-13 14:22:00 -04:00
d9da05bd02
cubepilot_cubeorange: Update bootloader defconfig NuttX 10.1.0+
2021-08-13 14:22:00 -04:00
2a4b4824e5
cubepilot_cubeorange: Update nsh defconfig NuttX 10.1.0+
2021-08-13 14:22:00 -04:00
f5b22d8832
cubepilot_cubeorange: Update test defconfig NuttX 10.1.0+
2021-08-13 14:22:00 -04:00
5f775b508f
boards: enable CONFIG_OTG_ID_GPIO_DISABLE on all F7/H7
2021-06-01 15:19:15 -04:00
58b40fbbb9
boards: move testing to dedicated test variants
2021-04-14 09:21:31 +02:00
43da43ddc6
boards: cubepilot cubeorange Add remaining SRAM4 & DTCM to heap
2021-04-03 14:13:23 -04:00
6874e9fba0
boards: NuttX disable all NSH memory debug commands (mb, mh, mw) by default
...
- closes https://github.com/PX4/PX4-Autopilot/issues/17062
2021-03-30 09:23:43 -04:00
e77bffe582
boards: STM32H7 remove CONFIG_MM_REGIONS=3
2021-03-26 17:40:44 -04:00
cdcff35760
cubepilot cubeorange:Enable ADC3 in support of temperature sensing
2021-03-19 15:48:47 +01:00
7bc2393936
cubepilot cubeorange:Enable ADC3 in support of temperature sensing
2021-03-19 15:48:47 +01:00
a0b9b44ff6
boards: stm32h7 set CONFIG_SDMMC1 consistently
2021-03-09 09:37:05 -05:00
8f0918a16b
boards: remove unused linker __param section
2021-02-08 23:22:48 -05:00
1ec10bfcc6
boards: disable CONFIG_ARMV7M_LAZYFPU again ( #16573 )
...
- this was causing hard faults on the CUAV Nora and possibly other boards, disabling everywhere until we fully understand the root cause
2021-01-17 22:40:21 -05:00
cb74cb8692
boards: enable CONFIG_ARMV7M_LAZYFPU everywhere
2021-01-12 09:04:38 +01:00
c60743b306
boards: NuttX increase file name max 32 -> 40
2020-11-08 12:51:59 -05:00
233949a377
NuttX upgrade to 10.0.0+ defconfig changes
2020-10-28 14:25:25 -04:00
2728af4264
boards: cubeorange and cubeyellow disable serial console (used for ADSB on new carrier boards)
...
- add console builds (cubepilot_cubeorange_console) for hardware test rack and developers
2020-09-21 11:53:49 -04:00
0d9d1e79e8
cubepilot_cubeorange: Updates for NuttX 9.1.0+ External schedule_note
2020-09-16 21:32:04 -04:00
5691bf1dee
cubepilot_cubeorange Updates for NuttX 9.1.0-
...
cubepilot_cubeorange: defconfig MMCSD enable multiblock
2020-09-16 21:32:04 -04:00
2c3441aa90
boards: reduce CONFIG_NFILE_DESCRIPTORS 15 -> 12
...
- reduced now that calibration uses uORB::Subscription
- can likely be reduced further (perhaps < 8) with additional testing
2020-08-21 10:12:13 -04:00
91ad8473ab
boards: cubepilot/cubeorange small fixes and improvements
...
- defconfig UART sync with cube yellow (and other boards)
- manually start ak09916 (Here2) on I2C2 with proper rotation
2020-08-16 17:45:47 -04:00
cfbf69f2a7
boards: rename Hex -> CubePilot
...
- hex_cube-orange_default -> cubepilot_cubeorange_default
- hex_cube-yellow_default -> cubepilot_cubeyellow_default
2020-07-26 13:55:41 -04:00
Jacob Dahl