* Tools: rewrite uploader script
This adds a script called px4_uploader.py which is a complete rewrite
using Claude Code of px_uploader.py.
The main improvements over the previous px_uploader.py script are:
- Separate smaller classes instead of one big uploader class.
- Easier debugging with --verbose or --debug flags.
- Nicer progress animation.
- No more hard to debug Exception swallowing over multiple levels.
- Auto-detection and looping of devices, removing the functionality from
cmake.
- Auto-detection of PX4 devices by USB VID/PID.
- Add noninteractive mode
- Add JSON output mode
* rt106x: Use platform SPI hal layer
* rt106x: Add romapi support and reboot to isp/bootloader
* bootloader: imxrt_common: Add rt106x support
* NXP MR-Tropic initial commit
* Add missing file for mr-tropic bootloader
* nxp-mr-tropic:Bootloader Alow Assertion debugging & Keep Ram Vectors
* nxp-mr-tropic: Firmware Boot from bootloader
* nxp-mr-tropic:Add Bootloader bin file
* mr-tropic: Update config and linker
Fixes enet issues with write-back and some code cleanup.
Furthermore increase NOR LittleFS to 256kB to reflect on linker
* Update NuttX
* mr-tropic: fix itcm apping and add mr-tropic to itcm check
---------
Co-authored-by: David Sidrane <David.Sidrane@NscDg.com>
nsh console running on USB
param module running
working with i2c and common drivers
provided implementation for drv_pwm_output.h
i2cdetect working as expected with no device
mavlink started succesfully
mounts sd card and logger runs
logger to file succesfully
pwm_servo implemented without using Nuttx lib
pwm_out outputs expected waveforms
- however currently if the frequency is higher than what the pwm_out
driver runs, there will be aliasing, based on how the registers gets
resets
wifi softap working
- Seeing wifi hotspot
- cant connect due to wrong password
- problems with adjusting ssid and password
wifi ssid and password being set accordinglu
connected to wifi hotspot with dhpcd
- made some changes to nuttx to only build for SoftAP mode, however this
was effectivelyy removing the ifdef for STATION mode. Should investigate
the coexist option again
added ifdef to not use timer 0 when wifi enabled
- reverted esp32 rt_timer to make use of timer 0 by default
fix setting incorrect bit in hrt timer register
- hrt running as expected, but on startup the pwm_out driver starts up
at about 200Hz and then rises over a minute or so 250Hz. Not sure if
this was present previously, and could be due to Wifi running at time
priority on timer 0
pull xtensa compilers in setup.ubuntu.sh
revert logger stacksize and cmake argument
esp32 chip revision and PX4 UUID implemented
spi board reset implemented, formatting checked
devkit acts on startup as a wifi bridge for comms
- the most usefull setting for the general developer when buying a esp32 devkit
- testing Mavlink shell using ./Tools/mavlink_shell.py
- todo: Test mavlink messages being forward
improve wifi telemetry by increasing prio
- Remove power save mode on wifi
- increased daemon thread schedule priority to 50
compiles without Nuttx changes
- updated compiler settings to match those of nuttx on px4 side
add espressif_esp32 to excluded boards
ci: allow docker to find xtensa compilers
* Add tflm to px4 with module
- Add TensorFlow Lite Micro(TFLM) as a library in px4
- Make a module that uses neural network inference for control, which uses TFLM for inference
- Make board config files for PX4 with neural module
* Added neural flight mode
* Add posibility to read of inference times
* Fix comments from review:
- Switch ssh link to https link in submodule
- Remove mc_nn_control from startup
* Add tflm to px4 with module
- Add TensorFlow Lite Micro(TFLM) as a library in px4
- Make a module that uses neural network inference for control, which uses TFLM for inference
- Make board config files for PX4 with neural module
* Added neural flight mode
* Add posibility to read of inference times
* Remove auto start
* Add logging from neural control module
* Fix automatic startup to only be when module is included
* Switch to flight mode registration
* Add docs
* Change min/max/coeff to actual parameters
* add figures to neural network docs
* Switch to e2e network
* Remove toolchain changes and replace with instructions in docs
* Get ready for merge after toolchain upgrade
* switch back to submodule
* Try to figure out cmake
* Get CI working with new toolchain
* Remove fork dependency
* Finalize PR
* fix toolchain inclusion
* Fix ctype_base.h include
* Cleanup includes for TFLM
* Remove redundant std
* Update FW module names in board files
* Fix docs
* Remove cstdlib copy
* Copy header from nuttx
* Prettier, markup, layout
* NeuralControl.msg - update uorb comments to current standard
* Add description to neural topic
* Fix typo
* Typo
* TFLM and Module utitlities
* Neural networks top level
* Update docs
* Add manual control
* Update docs
* Revert the manual control attempt
* Update docs/en/advanced/nn_module_utilities.md
* Add posibility to set trajectory setpoint with manual control
---------
Co-authored-by: Pedro Roque <padr@kth.se>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
* feat: configurable board pwm freq from Kconfig
* feat: add board_pwm_config to submenu
* fix: define sequence correction
* fix: revert Tools/simulation/gz
* fix: track upstream gz
* fix: track upstream mavlink
* feat: adjustable pwm for multiple board types
* feat: add conditional check for CONFIG_ for correct fallback
* add: spacecraft board with correct BOARD_PWM_FREQ supporting 10Hz actuation rate
* fix: set dependencies for submenu arch chips
* fix: keep only upper arch level
* fix: proper checking - still not showing up for board config
* feat: add hidden kconfig for platforms
* Merge Nuttx config into px4board
Allows to expose nuttx into PX4 if needed
* Kconfig: Include nuttx symbols in updateconfig
Only if applicable i.e. defined in the kconfig
* fix: merged config with previously generated boardconfig
* doc: updated code comment
---------
Co-authored-by: Daniel Agar <daniel@agar.ca>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
imxrt:117x Reuse all but io_timer_hw_description and imxrt_pinirq.c
imxrt:ADC & LPADC bifurcation and restructuring
imxrt:hrt support Up to GPT6
nxp/rt117x:adc Corrected
- new ROS2 platform in PX4 intended for creating configs that build and run entirely in ROS2
- PX4_CONFIG defaults to px4_ros2_default if no config specified and in a colcon workspace with ROS_VERSION=2
- currently doesn't do much other than allow you to build px4 msgs interface package
the nuttx and posix specific options files since this option cannot be used with
the qurt platform. There are header files in the hexagon sdk that fail this check.
For NuttX protected or kernel build, the prebuilds can't contain libraries which are
different for kernel and user-space in protected/kerenl builds
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
- use NuttX gdb script for nxthreads and thread backtrace
- update jlink_gdb_backtrace and jlink_debug_gdb helper targets to use
NuttX gdb script
- Debug/PX4 fix "perf" divide by zero
- Debug/PX4 add "dmesg"
- cmake NuttX build wrapper compile in place instead of copying source tree to build directory
- slightly faster skipping necessary copying (depending on system)
- allows debugging in place
- easier to work directly in NuttX following official documentation
- simplifies overall build which should make it easier to resolve any remaining NuttX dependency issues in the build system
- the downside is switching back and forth between different builds always require rebuilding NuttX, but I think this is worth the improved developer experience
- also no longer builds px4io and bootloader in every single build, for most users these rarely change and we're wasting a lot of build time
The bulk of this change was tightly coupled and needed to be deleted in one pass. Some of the smaller changes were things that broke as a result of the initial purge and subsequently fixed by further eradicating unnecessary platform differences. Finally, I deleted any dead code I came across in the related files I touched while going through everything.
- DriverFramework (src/lib/DriverFramework submodule) completely removed
- added dspal submodule in qurt platform (was brought in via DriverFramework)
- all df wrapper drivers removed
- all boards using df wrapper drivers updated to use in tree equivalents
- unused empty arch/board.h on posix and qurt removed
- unused IOCTLs removed (pub block, priv, etc)
- Integrator delete methods only used from df wrapper drivers
- commander: sensor calibration use "NuttX version" everywhere for now
- sensors: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- battery_status: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- cdev cleanup conflicting typedefs and names with actual OS (pollevent_t, etc)
- load_mon and top remove from linux boards (unused)
- delete unused PX4_MAIN_FUNCTION
- delete unused getreg32 macro
- delete unused SIOCDEVPRIVATE define
- named each platform tasks consistently
- posix list_devices and list_topics removed (list_files now shows all virtual files)
- instrumenting PX4 Matrix and Param methods is too burdensome
- partially restore px4_fmu-v5_stackcheck and holybro_durandal-v1_stackcheck to match default configs
