It was added at a time where the triplet target was directly fed as position setpoint to the controller.
Since the smoothing improvements to FlightTaskAuto(SmoothVel) and removing the previous "aggressive" FlightTaskAuto variant there should be no need anymore for this logic. It can sometimes lead to unexpected sideffects. E.g. the vehicle would suddenly change direction when exceeding some arbitrary threshold.
* Implemented driver for MCP23017
* fixed compatability with mcp23009. (naming of instantiated GPIO-Devices)
* removed some comments
* removed even more comments
* commented out instatntiation of driver since it will not be used with v6x
* removed last useless comments
* re-activated gpio_mcp23009 driver, removed useless comments and empty lines
* removed empty lines at the end of mcp23017.cpp
* removed empty line
* Implemented driver for MCP23017
* fixed compatability with mcp23009. (naming of instantiated GPIO-Devices)
* removed some comments
* removed even more comments
* commented out instatntiation of driver since it will not be used with v6x
* removed last useless comments
* re-activated gpio_mcp23009 driver, removed useless comments and empty lines
* removed empty lines at the end of mcp23017.cpp
* removed empty line
* basic working implementation
* first improved driver version with shared code base for MCP23009 & MCP23017 (built as state machine with sanity checks)
* removed unused imports
* changed module name from MCP to MCP230XX
* removed debug print statements
* adjusted auto start command of driver
* removed comments
* -added seperate main functions for both derivative modules (mcp23009 and mcp23017)
* compile common functions as shared library in src/lib/drivers
* fixed cleanup of modules
* ->unclean working version with shared common library
* used make format
* working & cleaned version
* -> Added CallbackHandler to be able to use multiple reading GPIO-expanders simultaneously
-> Removed old mcap23009 calls and pin registrations
-> Adjusted GpioIn.msg to contain MAX_INSTANCES
* ->removed unused imports
->used make format
* Fix: Re-enabled platform_mcp_gpio for accton-godwit, cuav, fmu-v5x
* Fix: enabled platform_mcp_gpio in px4/fmu-v5x
* added depency to fmu-v5x
* Fix: removed new lines
* Fix: fixed linker errors
* removed unused linkage against mcp-library
* Made mcp start calls consistent for fmu-v5x and fmu-v6x
* moved logging of comm errors to read/write function directly
* added perf_count for sanity_check
* removed error message
* ensured member variables follow naming convention
* added retries to probe function
* simplyfied state-logic
* add break to terminate loop early
* ensured clean state when register_gpios() fails
* add registered-flag to pins
* used path from top dir instead of relative path in CMakeLists
* used constexpr to set parameters instead of calculating them at runtime
* style: used make format
* fix: corrected i2c_bus assignment
* style: init input of callbackhandler to 0
* fix: mark pin as registered if successful
* style: made arguments const type
---------
Co-authored-by: Alexander Lerach <alexander@auterion.com>
Move ramvectors from DTCM to ITCM, this seems to better in general.
Also ITCM is marked as RO so is safer anyhow, now that DTCM is fully
unused we add DTCM region of 256kB to memory allocator. Increases usable
memory from 1536kB to 1792kB and decrease system load a bit since DTCM
is faster
- remove commander test ratio "tuning knobs" (COM_ARM_EKF_{HGT,POS,VEL,YAW})
- these are effectively redundant with the actual tuning (noise & gate)
in the estimator, plus most users have no idea why they'd be
adjusting these other than to silence an annoying preflight complaint
- remove ekf2 "PreFlightChecker" with hard coded innovation limits
- ekf2 preflight innovation flags are now simply if any active source
exceeds half the limit preflight
192.168.0.x is often used by routers for WIFI/ethernet networks, and thus
can create conflicts.
This can happen for example if a companion is connected to the FMU via
ethernet and at the same time connects to a WIFI network as DHCP client.
nxp/rt117x:Fix Pin IRQ
nxp/rt117x:Support 4 i2c busses
nxp/rt117x:Add px4io_serial support
nxp/imxrt:Expand ToneAlarmInterface to GPT 3 & 4
px4_fmu-6xrt:Using imxrt_flexspi_nor_octal
px4_fmu-6xrt:Entry is start
px4_fmu-6xrt:Add Proper MTD
px4_fmu-6xrt:Set I2C Buses
px4_fmu-6xrt:Proper SPI usage
px4_fmu-6xrt:Adjust memory Map to use the 2 MB
px4_fmu-6xrt:Bring in ROMAPI
px4_fmu-6xrt:Push FLASH to 200Mhz
px4_fmu-6xrt:Use BOARD_I2C_LATEINIT
px4_fmu-6xrt:Clock Config remove unused devices
px4_fmu-6xrt:Remove EVK SDRAM IO
px4_fmu-6xrt:Enable SE550 using HW_VER_REV_DRIVE
px4_fmu-6xrt:Use MTD to mount FRAM on Flex SPI
px4_fmu-6xrt:Manifest
px4_fmu-6xrt:Restore board_peripheral_reset
px4_fmu-6xrt:Set I2C buss Interna/Externa and startup
nxp/rt117x:Set 6 I2C busses
px4_fmu-6xrt:Correct Clock Sources and Freqency Settings
px4_fmu-6xrt:Correct ADC Settings
px4_fmu-6xrt:Tune FlexSPI config and sync header with debug variant Linker prep for rodata ahb partitioning
px4_fmu-6xrt:FlexSPI prefetch partition split .text and .rodata
Current config
1KB Prefetch .rodata
3KB Prefetch .text
px4_fmu-6xrt:Run imxrt_flash_setup_prefetch_partition from ram with barriers
px4_fmu-6xrt:Use All OCTL setting from FLASH g_flash_config SANS lookupTable
px4_fmu-6xrt:Octal spi boot/debug problem bypass
px4_fmu-6xrt:Add PWM test
px4_fmu-6xrt:Fix clockconfig and USB vbus sense
px4_fmu-6xrt: Use TCM
px4_fmu-6xrt: Ethernet bringup
imxrt: use unique_id register for board_identity
px4_fmu-6xrt: update ITCM mapping, todo proper trap on pc hitting 0x0
px4_fmu-6xrt:correct rotation icm42688p onboard imu
rt117x: Add SSARC HP RAM driver for memory dumps
px4_fmu-6xrt: Enable hardfault_log
px4_fmu-6xrt: Enable DMA pool
px4_fmu-6xrt: fix uart mapping
px4_fmu-6xrt: enable SocketCAN & DroneCAN
px4_fmu-6xrt:Command line history TAB completion
px4_fmu-6xrt:Fix pinning duplication
px4_fmu-6xrt:Support conditional PHY address based on selected PHY
px4_fmu-6xrt:Add Pull Downs on CTS, use GPIO for RTS
px4_fmu-6xrt:Set TelemN TX Slew rate and Drive Strenth to max
px4_fmu-6xrt::Set TELEM Buffers add HW HS
px4_fmu-6xrt:Turn off DMA poll
px4_fmu-6xrt:RC_SERIAL_PORT needed to be px4io to disable rc_input using TELEM2!
px4_fmu-6xrt: bootloader (#22228)
* imxrt:Add bootloader support
* bootloader:imxrt clear BOOT_RTC_SIGNATURE
* px4_fmu-6xrt:Add bootloader
* px4_fmu-6xrt:bootloader removed ADC
* px4_fmu-6xrt:bootloader base bootloader script off of script.ld
* px4_fmu-6xrt:add _bootdelay_signature & change entry from 0x30000000 to 0x30040000
* px4_fmu-6xrt:hw_config Bootloader has to have 12 bytes
px4_fmu-6xrt:Default to use LAN8742A PHY
px4_fmu-v6xrt:VID Set to Drone Code
board_reset:Enable ability to write RTC GP regs
px4_fmu-6xrt:Fix CMP0079 error
rt117x:micro_hal Add a PX4_MAKE_GPIO_PULLED_INPUT
px4_fmu-v6xrt:Set CTS High before VDD_5V applided to ports to avoid radios fro entering bootloaders
fmu-v6xrt: increase 5v down time
fmu-v6xrt:Ready for Release DEBUGASSERTS off and Console 57600,
Bootloder updated.
imxrt:board_hw_rev_ver Rework for 3.893V Ref
px4_fmu-v6xrt:Move ADC to Port3
Jacob Dahl