WIP: common board init

boards: px4_fmu-v5/v5x init all I2C pins
2026-05-30 02:00:05 +08:00 · 2022-05-04 18:31:40 -04:00 · 2022-05-04 14:02:23 -04:00
1289 changed files with 24164 additions and 84718 deletions
@@ -61,20 +61,18 @@ pipeline {
                     "holybro_kakutef7_default",
                     "holybro_kakuteh7_default",
                     "holybro_pix32v5_default",
+                     "matek_h743-slim",
                     "matek_gnss-m9n-f4_canbootloader",
                     "matek_gnss-m9n-f4_default",
-                     "matek_h743-mini_default",
-                     "matek_h743-slim_default",
-                     "matek_h743_default",
                     "modalai_fc-v1_default",
                     "modalai_fc-v1_rtps",
                     "modalai_fc-v2_default",
                     "mro_ctrl-zero-f7_default",
                     "mro_ctrl-zero-f7-oem_default",
-                     "mro_ctrl-zero-h7-oem_default",
-                     "mro_ctrl-zero-h7-oem_rtps",
                     "mro_ctrl-zero-h7_default",
                     "mro_ctrl-zero-h7_rtps",
+                     "mro_ctrl-zero-h7-oem_default",
+                     "mro_ctrl-zero-h7-oem_rtps",
                     "mro_pixracerpro_default",
                     "mro_pixracerpro_rtps",
                     "mro_x21-777_default",
@@ -89,27 +87,26 @@ pipeline {
                     "nxp_ucans32k146_canbootloader",
                     "nxp_ucans32k146_default",
                     "omnibus_f4sd_default",
+                     "raspberrypi_pico_default",
                     "px4_fmu-v2_default",
                     "px4_fmu-v2_fixedwing",
-                     "px4_fmu-v2_lto",
                     "px4_fmu-v2_multicopter",
                     "px4_fmu-v2_rover",
+                     "px4_fmu-v2_lto",
                     "px4_fmu-v3_default",
                     "px4_fmu-v4_default",
                     "px4_fmu-v4pro_default",
-                     "px4_fmu-v5_cyphal",
                     "px4_fmu-v5_debug",
                     "px4_fmu-v5_default",
-                     "px4_fmu-v5_lto",
                     "px4_fmu-v5_rtps",
                     "px4_fmu-v5_stackcheck",
                     "px4_fmu-v5_uavcanv0periph",
+                     "px4_fmu-v5_uavcanv1",
+                     "px4_fmu-v5_lto",
                     "px4_fmu-v5x_default",
-                     "px4_fmu-v6c_default",
                     "px4_fmu-v6u_default",
                     "px4_fmu-v6x_default",
                     "px4_io-v2_default",
-                     "raspberrypi_pico_default",
                     "sky-drones_smartap-airlink_default",
                     "spracing_h7extreme_default",
                     "uvify_core_default"
@@ -794,7 +794,7 @@ void resetParameters() {
 void runTests() {

  // test loading a range of airframes
-  sh './Tools/HIL/test_airframes.sh `find /dev/serial -name *usb-*` 2100 3000 4001 6001 8001 10016'
+  sh './Tools/HIL/test_airframes.sh `find /dev/serial -name *usb-*` 1000 1001 2100 3000 4001 6001 8001 10016'

  resetParameters()

@@ -809,9 +809,6 @@ void runTests() {
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "top once"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "work_queue status"'

-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "ostest"'
-  sh './Tools/HIL/reboot.py --device `find /dev/serial -name *usb-*`' // reboot after ostest
-
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "commander_tests" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "controllib_test"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "lightware_laser_test"'
@@ -867,15 +864,12 @@ void printTopics() {
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener cpuload" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener distance_sensor" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener ekf2_timestamps" || true'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_gps_status" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener esc_status" || true'
-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_aid_src_fake_pos" || true'
-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_aid_src_gnss_pos" || true'
-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_aid_src_gnss_vel" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_attitude" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_baro_bias" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_event_flags" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_global_position" || true'
-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_gps_status" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_innovation_test_ratios" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_innovation_variances" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_innovations" || true'
@@ -1,17 +1,11 @@
 ---
 Checks:          '*,
-                  -*-avoid-c-arrays,
-                  -*-uppercase-literal-suffix,
-                  -*-magic-numbers,
-                  -altera-id-dependent-backward-branch,
-                  -altera-unroll-loops,
                  -android*,
                  -bugprone-integer-division,
                  -cert-dcl50-cpp,
                  -cert-env33-c,
                  -cert-err34-c,
                  -cert-err58-cpp,
-                  -cert-flp30-c,
                  -cert-msc30-c,
                  -cert-msc50-cpp,
                  -clang-analyzer-core.CallAndMessage,
@@ -24,7 +18,6 @@ Checks:          '*,
                  -clang-analyzer-deadcode.DeadStores,
                  -clang-analyzer-optin.cplusplus.VirtualCall,
                  -clang-analyzer-optin.performance.Padding,
-                  -clang-analyzer-security.FloatLoopCounter,
                  -clang-analyzer-security.insecureAPI.strcpy,
                  -clang-analyzer-unix.API,
                  -clang-analyzer-unix.cstring.BadSizeArg,
@@ -44,7 +37,8 @@ Checks:          '*,
                  -cppcoreguidelines-pro-type-union-access,
                  -cppcoreguidelines-pro-type-vararg,
                  -cppcoreguidelines-special-member-functions,
-                  -fuchsia-*,
+                  -fuchsia-default-arguments,
+                  -fuchsia-overloaded-operator,
                  -google-build-using-namespace,
                  -google-explicit-constructor,
                  -google-global-names-in-headers,
@@ -68,7 +62,6 @@ Checks:          '*,
                  -hicpp-use-equals-delete,
                  -hicpp-use-override,
                  -hicpp-vararg,
-                  -llvmlibc-*,
                  -llvm-header-guard,
                  -llvm-include-order,
                  -llvm-namespace-comment,
@@ -91,7 +84,6 @@ Checks:          '*,
                  -modernize-use-override,
                  -modernize-use-trailing-return-type,
                  -modernize-use-using,
-                  -modernize-use-trailing-return-type,
                  -performance-inefficient-string-concatenation,
                  -readability-avoid-const-params-in-decls,
                  -readability-container-size-empty,
@@ -1,34 +1,32 @@
 ---
-name: 🐛 Bug report
+name: Bug report
 about: Create a report to help us improve
-labels: bug-report

 ---

-## Describe the bug
+**Describe the bug**
 A clear and concise description of the bug.

-## To Reproduce
+**To Reproduce**
 Steps to reproduce the behavior:
 1. Drone switched on '...'
 2. Uploaded mission '....' (attach QGC mission file)
 3. Took off '....'
 4. See error

-## Expected behavior
+**Expected behavior**
 A clear and concise description of what you expected to happen.

-## Log Files and Screenshots
+**Log Files and Screenshots**
 *Always* provide a link to the flight log file:
- Download the flight log file from the vehicle ([tutorial](https://docs.px4.io/main/en/getting_started/flight_reporting.html)).
- Upload the log to the [PX4 Flight Review](http://logs.px4.io/)
- Share the link to the log (Copy and paste the URL of the log)
+- Download the flight log file from the vehicle ([tutorial](https://docs.px4.io/master/en/getting_started/flight_reporting.html)).
+- Share the link to a log showing the problem on [PX4 Flight Review](http://logs.px4.io/).

 Add screenshots to help explain your problem.

-## Drone (please complete the following information):
+**Drone (please complete the following information):**
 - Describe the type of drone.
 - Photo of the IMU / autopilot setup if possible.

-## Additional context
+**Additional context**
 Add any other context about the problem here.
@@ -1,20 +1,19 @@
 ---
 name: 🚀 Feature Request
 about: Suggest an idea for this project
-labels: feature-request

 ---

 For general questions please use [PX4 Discuss](http://discuss.px4.io/) or Slack (you can find an invite link on this project README).

-## Describe problem solved by the proposed feature
+**Describe problem solved by the proposed feature**
 A clear and concise description of the problem, if any, this feature will solve. E.g. I'm always frustrated when ...

-## Describe your preferred solution
+**Describe your preferred solution**
 A clear and concise description of what you want to happen.

-## Describe possible alternatives
+**Describe possible alternatives**
 A clear and concise description of alternative solutions or features you've considered.

-## Additional context
+**Additional context**
 Add any other context or screenshots for the feature request here.
@@ -1,13 +1,10 @@
 ---
 name: ⛔ Support Question
-about: See http://discuss.px4.io/ for questions about using PX4.
+about: See [PX4 Discuss](http://discuss.px4.io/) for questions about using PX4.

 ---

-## Attention! Please read the note below
-
-We use GitHub issues only to discuss PX4 bugs and new features.
-
-**For questions about using PX4 or related components, please use [PX4 Discuss](http://discuss.px4.io/).**
+We use GitHub issues only to discuss PX4 bugs and new features. For
+questions about using PX4 or related components, please use [PX4 Discuss](http://discuss.px4.io/).

 Thanks!
@@ -1,11 +1,9 @@
 ---
 name: ⛔ Documentation Issue
-about: See https://github.com/PX4/px4_user_guide for documentation issues
+about: See https://github.com/PX4/Devguide for documentation issues

 ---

-## Attention! Please read the note below
-
-**Please submit the documentation issue to the [User Guide](https://github.com/PX4/px4_user_guide) repository.**
+PX4 has dedicated repositories for developer documentation (https://github.com/PX4/Devguide) and user documentation (https://github.com/PX4/px4_user_guide).

 Thanks!
@@ -37,10 +37,8 @@ jobs:
          holybro_kakutef7,
          holybro_kakuteh7,
          holybro_pix32v5,
-          matek_gnss-m9n-f4,
-          matek_h743,
-          matek_h743-mini,
          matek_h743-slim,
+          matek_gnss-m9n-f4,
          modalai_fc-v1,
          modalai_fc-v2,
          mro_ctrl-zero-f7,
@@ -55,16 +53,15 @@ jobs:
          nxp_fmurt1062-v1,
          nxp_ucans32k146,
          omnibus_f4sd,
+          raspberrypi_pico,
          px4_fmu-v2,
          px4_fmu-v3,
          px4_fmu-v4,
          px4_fmu-v4pro,
          px4_fmu-v5,
          px4_fmu-v5x,
-          px4_fmu-v6c,
          px4_fmu-v6u,
          px4_fmu-v6x,
-          raspberrypi_pico,
          sky-drones_smartap-airlink,
          spracing_h7extreme,
          uvify_core
@@ -36,14 +36,14 @@
 [submodule "Tools/jsbsim_bridge"]
 	path = Tools/jsbsim_bridge
 	url = https://github.com/PX4/px4-jsbsim-bridge.git
-[submodule "src/drivers/cyphal/libcanard"]
-	path = src/drivers/cyphal/libcanard
-	url = https://github.com/opencyphal/libcanard.git
-[submodule "src/drivers/cyphal/public_regulated_data_types"]
-	path = src/drivers/cyphal/public_regulated_data_types
-	url = https://github.com/opencyphal/public_regulated_data_types.git
-[submodule "src/drivers/cyphal/legacy_data_types"]
-	path = src/drivers/cyphal/legacy_data_types
+[submodule "src/drivers/uavcan_v1/libcanard"]
+	path = src/drivers/uavcan_v1/libcanard
+	url = https://github.com/UAVCAN/libcanard.git
+[submodule "src/drivers/uavcan_v1/public_regulated_data_types"]
+	path = src/drivers/uavcan_v1/public_regulated_data_types
+	url = https://github.com/UAVCAN/public_regulated_data_types.git
+[submodule "src/drivers/uavcan_v1/legacy_data_types"]
+	path = src/drivers/uavcan_v1/legacy_data_types
 	url = https://github.com/PX4/public_regulated_data_types.git
 	branch = legacy
 [submodule "src/lib/crypto/monocypher"]
@@ -53,6 +53,9 @@
 [submodule "src/lib/events/libevents"]
 	path = src/lib/events/libevents
 	url = https://github.com/mavlink/libevents.git
+[submodule "Tools/simulation-ignition"]
+	path = Tools/simulation-ignition
+	url = https://github.com/PX4/px4-simulation-ignition.git
 [submodule "src/lib/crypto/libtomcrypt"]
 	path = src/lib/crypto/libtomcrypt
 	url = https://github.com/PX4/libtomcrypt.git
@@ -9,5 +9,3 @@ launch.json
 ipch/

 browse.vc.db*
-
-*.log
@@ -6,11 +6,6 @@ CONFIG:
      buildType: RelWithDebInfo
      settings:
        CONFIG: px4_sitl_default
-    px4_sitl_ign:
-      short: px4_sitl_ign
-      buildType: RelWithDebInfo
-      settings:
-        CONFIG: px4_sitl_ign
    px4_sitl_rtps:
      short: px4_sitl_rtps
      buildType: RelWithDebInfo
@@ -126,6 +126,8 @@
        },
        "search.showLineNumbers": true,
        "telemetry.enableTelemetry": false,
+        "terminal.integrated.copyOnSelection": true,
+        "terminal.integrated.rightClickBehavior": "paste",
        "terminal.integrated.scrollback": 5000,
        "window.title": "${dirty} ${activeEditorMedium}${separator}${rootName}",
        "workbench.editor.highlightModifiedTabs": true,
@@ -49,18 +49,34 @@
                "group": "test"
            }
        },
-
        {
-            "label": "gazebo",
+            "label": "jmavsim build",
            "type": "shell",
+            "command": "ant create_run_jar copy_res",
            "options": {
-                "cwd": "${workspaceFolder}",
+                "cwd": "${workspaceFolder}/Tools/jMAVSim"
+            },
+            "problemMatcher": [],
+            "presentation":{
+                "echo": true,
+                "reveal": "never",
+                "focus": false,
+                "panel": "shared",
+                "showReuseMessage": false,
+                "clear": false,
+            }
+        },
+        {
+            "label": "jmavsim",
+            "type": "shell",
+            "dependsOn": "jmavsim build",
+            "command": "java -Djava.ext.dirs= -jar jmavsim_run.jar -r 250 -lockstep -tcp localhost:4560 -qgc",
+            "options": {
+                "cwd": "${workspaceFolder}/Tools/jMAVSim/out/production",
                "env": {
-                    "IGN_GAZEBO_RESOURCE_PATH": "${workspaceFolder}/Tools/simulation/gazebo/models",
                    "PX4_SIM_SPEED_FACTOR": "1"
                }
            },
-            "command": "ign gazebo -v 4 -r ${workspaceFolder}/Tools/simulation/gazebo/worlds/${input:gazeboWorld}.sdf",
            "isBackground": true,
            "presentation": {
                "echo": true,
@@ -88,11 +104,161 @@
                }
            ]
        },
-
+        {
+            "label": "jmavsim kill",
+            "type": "shell",
+            "command": "kill $(ps aux | grep jmavsim | grep -v 'grep' | awk '{print $2}')",
+            "presentation": {
+                "echo": false,
+                "reveal": "never",
+                "focus": false,
+                "panel": "shared",
+                "showReuseMessage": false,
+                "clear": false
+            },
+            "problemMatcher": []
+        },
+        {
+            "label": "gazebo build",
+            "type": "shell",
+            "command": "make px4_sitl_default sitl_gazebo",
+            "options": {
+                "cwd": "${workspaceFolder}"
+            },
+            "problemMatcher": [],
+            "presentation":{
+                "echo": true,
+                "reveal": "always",
+                "focus": false,
+                "panel": "shared",
+                "showReuseMessage": false,
+                "clear": false,
+            }
+        },
+        {
+            "label": "gazebo start",
+            "type": "shell",
+            "dependsOn": "gazebo build",
+            "options": {
+                "cwd": "${workspaceFolder}",
+                "env": {
+                    "GAZEBO_PLUGIN_PATH": "${workspaceFolder}/build/px4_sitl_default/build_gazebo",
+                    "GAZEBO_MODEL_PATH": "${workspaceFolder}/Tools/sitl_gazebo/models",
+                    "PX4_SIM_SPEED_FACTOR": "1"
+                }
+            },
+            "command": "gzserver --verbose ${workspaceFolder}/Tools/sitl_gazebo/worlds/${input:gazeboWorld}.world",
+            "isBackground": true,
+            "presentation": {
+                "echo": true,
+                "reveal": "never",
+                "focus": false,
+                "panel": "shared",
+                "showReuseMessage": false,
+                "clear": false
+            },
+            "problemMatcher": [
+                {
+                    "pattern": [
+                        {
+                            "regexp": ".",
+                            "file": 1,
+                            "location": 2,
+                            "message": 3
+                        }
+                    ],
+                    "background": {
+                        "activeOnStart": true,
+                        "beginsPattern": ".",
+                        "endsPattern": ".",
+                    }
+                }
+            ]
+        },
+        {
+            "label": "gazebo",
+            "type": "shell",
+            "dependsOn": "gazebo start",
+            "options": {
+                "cwd": "${workspaceFolder}",
+                "env": {
+                    "GAZEBO_PLUGIN_PATH": "${workspaceFolder}/build/px4_sitl_default/build_gazebo",
+                    "GAZEBO_MODEL_PATH": "${workspaceFolder}/Tools/sitl_gazebo/models",
+                    "PX4_SIM_SPEED_FACTOR": "1"
+                }
+            },
+            "command": "gz model --verbose --spawn-file=${workspaceFolder}/Tools/sitl_gazebo/models/${input:vehicleModel}/${input:vehicleModel}.sdf --model-name=${input:vehicleModel} -x 1.01 -y 0.98 -z 0.83",
+            "isBackground": false,
+            "presentation": {
+                "echo": true,
+                "reveal": "never",
+                "focus": false,
+                "panel": "shared",
+                "showReuseMessage": false,
+                "clear": false
+            },
+            "problemMatcher": [
+                {
+                    "pattern": [
+                        {
+                            "regexp": ".",
+                            "file": 1,
+                            "location": 2,
+                            "message": 3
+                        }
+                    ],
+                    "background": {
+                        "activeOnStart": true,
+                        "beginsPattern": ".",
+                        "endsPattern": ".",
+                    }
+                }
+            ]
+        },
+        {
+            "label": "gazebo client",
+            "type": "shell",
+            "dependsOn": "gazebo build",
+            "options": {
+                "cwd": "${workspaceFolder}",
+                "env": {
+                    "GAZEBO_PLUGIN_PATH": "${workspaceFolder}/build/px4_sitl_default/build_gazebo",
+                    "GAZEBO_MODEL_PATH": "${workspaceFolder}/Tools/sitl_gazebo/models",
+                    "PX4_SIM_SPEED_FACTOR": "1"
+                }
+            },
+            "command": "gzclient --verbose",
+            "isBackground": true,
+            "presentation": {
+                "echo": true,
+                "reveal": "never",
+                "focus": false,
+                "panel": "shared",
+                "showReuseMessage": false,
+                "clear": false
+            },
+            "problemMatcher": [
+                {
+                    "pattern": [
+                        {
+                            "regexp": ".",
+                            "file": 1,
+                            "location": 2,
+                            "message": 3
+                        }
+                    ],
+                    "background": {
+                        "activeOnStart": true,
+                        "beginsPattern": ".",
+                        "endsPattern": ".",
+                    }
+                }
+            ]
+        },
        {
            "label": "gazebo kill",
            "type": "shell",
-            "command": "killall ign",
+            "command": "killall gzserver",
            "presentation": {
                "echo": true,
                "reveal": "silent",
@@ -104,7 +270,6 @@
            "problemMatcher": [],
            "dependsOn":["px4_sitl_cleanup"]
        },
-
        {
            "label": "px4_sitl_cleanup",
            "type": "shell",
@@ -170,14 +335,39 @@
        }
    ],
    "inputs": [
+        {
+            "type": "pickString",
+            "id": "vehicleModel",
+            "description": "gazebo model",
+            "options": [
+              "iris",
+              "typhoon_h480",
+              "plane",
+              "plane_catapult",
+              "plane_lidar",
+              "standard_vtol",
+              "tailsitter",
+              "tiltrotor",
+              "r1_rover",
+              "boat"
+            ],
+            "default": "iris"
+        },
        {
            "type": "pickString",
            "id": "gazeboWorld",
            "description": "gazebo world",
            "options": [
-                "x4"
+                "baylands",
+                "empty",
+                "ksql_airport",
+                "mcmillan_airfield",
+                "sonoma_raceway",
+                "warehouse",
+                "windy",
+                "yosemite"
            ],
-            "default": "x4"
+            "default": "empty"
        }
    ]
 }
@@ -175,12 +175,6 @@ include(kconfig)
 message(STATUS "PX4 config: ${PX4_CONFIG}")
 message(STATUS "PX4 platform: ${PX4_PLATFORM}")

-if($ENV{CLION_IDE})
-	# CLion automatically executes some compiler commands after configuring the
-	# project. This would fail on NuttX, as visibility.h tries to (indirectly)
-	# include nuttx/config.h, which at that point does not exist yet
-	add_definitions(-DPX4_DISABLE_GCC_POISON)
-endif()

 if(${PX4_PLATFORM} STREQUAL "posix")
 	if(ENABLE_LOCKSTEP_SCHEDULER)
@@ -8,7 +8,7 @@ First [fork and clone](https://help.github.com/articles/fork-a-repo) the project

 ### Create a feature branch

-*Always* branch off main for new features.
+*Always* branch off master for new features.

 ```
 git checkout -b mydescriptivebranchname
@@ -16,7 +16,7 @@ git checkout -b mydescriptivebranchname

 ### Edit and build the code

-The [developer guide](https://docs.px4.io/main/en/development/development.html) explains how to set up the development environment on Mac OS, Linux or Windows. Please take note of our [coding style](https://docs.px4.io/main/en/contribute/code.html) when editing files.
+The [developer guide](http://dev.px4.io/) explains how to set up the development environment on Mac OS, Linux or Windows. Please take note of our [coding style](https://dev.px4.io/master/en/contribute/code.html) when editing files.

 ### Commit your changes

@@ -7,8 +7,7 @@ pipeline {
    stage('Analysis') {
      when {
        anyOf {
-          branch 'main'
-          branch 'master' // should be removed, but in case there is something going on...
+          branch 'master'
          branch 'pr-jenkins' // for testing
        }
      }
@@ -205,21 +204,20 @@ pipeline {
            unstash 'msg_documentation'
            unstash 'uorb_graph'
            withCredentials([usernamePassword(credentialsId: 'px4buildbot_github_personal_token', passwordVariable: 'GIT_PASS', usernameVariable: 'GIT_USER')]) {
-              sh('git clone https://${GIT_USER}:${GIT_PASS}@github.com/PX4/PX4-user_guide.git')
-              sh('cp airframes.md PX4-user_guide/en/airframes/airframe_reference.md')
-              sh('cp parameters.md PX4-user_guide/en/advanced_config/parameter_reference.md')
-              sh('cp -R modules/*.md PX4-user_guide/en/modules/')
-              sh('cp -R graph_*.json PX4-user_guide/.vuepress/public/en/middleware/')
-              sh('cp -R msg_docs/*.md PX4-user_guide/en/msg_docs/')
-              sh('cd PX4-user_guide; git status; git add .; git commit -a -m "Update PX4 Firmware metadata `date`" || true')
-              sh('cd PX4-user_guide; git push origin main || true')
-              sh('rm -rf PX4-user_guide')
+              sh('git clone https://${GIT_USER}:${GIT_PASS}@github.com/PX4/px4_user_guide.git')
+              sh('cp airframes.md px4_user_guide/en/airframes/airframe_reference.md')
+              sh('cp parameters.md px4_user_guide/en/advanced_config/parameter_reference.md')
+              sh('cp -R modules/*.md px4_user_guide/en/modules/')
+              sh('cp -R graph_*.json px4_user_guide/.vuepress/public/en/middleware/')
+              sh('cp -R msg_docs/*.md px4_user_guide/en/msg_docs/')
+              sh('cd px4_user_guide; git status; git add .; git commit -a -m "Update PX4 Firmware metadata `date`" || true')
+              sh('cd px4_user_guide; git push origin master || true')
+              sh('rm -rf px4_user_guide')
            }
          }
          when {
            anyOf {
-              branch 'main'
-              branch 'master' // should be removed, but in case there is something going on...
+              branch 'master'
              branch 'pr-jenkins' // for testing
            }
          }
@@ -247,8 +245,7 @@ pipeline {
          }
          when {
            anyOf {
-              branch 'main'
-              branch 'master' // should be removed, but in case there is something going on...
+              branch 'master'
              branch 'pr-jenkins' // for testing
            }
          }
@@ -281,8 +278,7 @@ pipeline {
          }
          when {
            anyOf {
-              branch 'main'
-              branch 'master' // should be removed, but in case there is something going on...
+              branch 'master'
              branch 'pr-jenkins' // for testing
            }
          }
@@ -311,8 +307,7 @@ pipeline {
          }
          when {
            anyOf {
-              branch 'main'
-              branch 'master' // should be removed, but in case there is something going on...
+              branch 'master'
              branch 'pr-jenkins' // for testing
            }
          }
@@ -355,8 +350,7 @@ pipeline {
          }
          when {
            anyOf {
-              branch 'main'
-              branch 'master' // should be removed, but in case there is something going on...
+              branch 'master'
              branch 'pr-jenkins' // for testing
            }
          }
@@ -379,8 +373,7 @@ pipeline {
          }
          when {
            anyOf {
-              branch 'main'
-              branch 'master' // should be removed, but in case there is something going on...
+              branch 'master'
              branch 'pr-jenkins' // for testing
            }
          }
@@ -325,13 +325,12 @@ px4io_update: px4_io-v2_default cubepilot_io-v2_default
 	cp build/px4_io-v2_default/px4_io-v2_default.bin boards/px4/fmu-v5/extras/px4_io-v2_default.bin
 	cp build/px4_io-v2_default/px4_io-v2_default.bin boards/px4/fmu-v5x/extras/px4_io-v2_default.bin
 	cp build/px4_io-v2_default/px4_io-v2_default.bin boards/px4/fmu-v6x/extras/px4_io-v2_default.bin
-	cp build/px4_io-v2_default/px4_io-v2_default.bin boards/px4/fmu-v6c/extras/px4_io-v2_default.bin
 	# cubepilot_io-v2_default
 	cp build/cubepilot_io-v2_default/cubepilot_io-v2_default.bin boards/cubepilot/cubeorange/extras/cubepilot_io-v2_default.bin
 	cp build/cubepilot_io-v2_default/cubepilot_io-v2_default.bin boards/cubepilot/cubeyellow/extras/cubepilot_io-v2_default.bin
 	git status

-bootloaders_update: cuav_nora_bootloader cuav_x7pro_bootloader cubepilot_cubeorange_bootloader holybro_durandal-v1_bootloader holybro_kakuteh7_bootloader matek_h743_bootloader matek_h743-mini_bootloader matek_h743-slim_bootloader modalai_fc-v2_bootloader mro_ctrl-zero-classic_bootloader mro_ctrl-zero-h7_bootloader mro_ctrl-zero-h7-oem_bootloader mro_pixracerpro_bootloader px4_fmu-v6c_bootloader px4_fmu-v6u_bootloader px4_fmu-v6x_bootloader
+bootloaders_update: cuav_nora_bootloader cuav_x7pro_bootloader cubepilot_cubeorange_bootloader holybro_durandal-v1_bootloader matek_h743-slim_bootloader modalai_fc-v2_bootloader mro_ctrl-zero-classic_bootloader mro_ctrl-zero-h7_bootloader mro_ctrl-zero-h7-oem_bootloader mro_pixracerpro_bootloader px4_fmu-v6u_bootloader px4_fmu-v6x_bootloader
 	git status

 .PHONY: coverity_scan
@@ -1,17 +1,17 @@
 Please use [PX4 Discuss](http://discuss.px4.io/) or [Slack](http://slack.px4.io/) to align on pull requests if necessary. You can then open draft pull requests to get early feedback.

-## Describe problem solved by this pull request
-A clear and concise description of the problem this proposed change will solve. Or, what it will improve.
+**Describe problem solved by this pull request**
+A clear and concise description of the problem this proposed change will solve.
 E.g. For this use case I ran into...

-## Describe your solution
+**Describe your solution**
 A clear and concise description of what you have implemented.

-## Describe possible alternatives
+**Describe possible alternatives**
 A clear and concise description of alternative solutions or features you've considered.

-## Test data / coverage
+**Test data / coverage**
 How was it tested? What cases were covered? Logs uploaded to https://review.px4.io/ and screenshots of the important plot parts.

-## Additional context
+**Additional context**
 Add any other related context or media.
@@ -6,38 +6,38 @@

 [![Slack](/.github/slack.svg)](https://join.slack.com/t/px4/shared_invite/zt-si4xo5qs-R4baYFmMjlrT4rQK5yUnaA)

-This repository holds the [PX4](http://px4.io) flight control solution for drones, with the main applications located in the [src/modules](https://github.com/PX4/PX4-Autopilot/tree/main/src/modules) directory. It also contains the PX4 Drone Middleware Platform, which provides drivers and middleware to run drones.
+This repository holds the [PX4](http://px4.io) flight control solution for drones, with the main applications located in the [src/modules](https://github.com/PX4/PX4-Autopilot/tree/master/src/modules) directory. It also contains the PX4 Drone Middleware Platform, which provides drivers and middleware to run drones.

 PX4 is highly portable, OS-independent and supports Linux, NuttX and MacOS out of the box.

-* Official Website: http://px4.io (License: BSD 3-clause, [LICENSE](https://github.com/PX4/PX4-Autopilot/blob/main/LICENSE))
-* [Supported airframes](https://docs.px4.io/main/en/airframes/airframe_reference.html) ([portfolio](https://px4.io/ecosystem/commercial-systems/)):
-  * [Multicopters](https://docs.px4.io/main/en/frames_multicopter/)
-  * [Fixed wing](https://docs.px4.io/main/en/frames_plane/)
-  * [VTOL](https://docs.px4.io/main/en/frames_vtol/)
-  * [Autogyro](https://docs.px4.io/main/en/frames_autogyro/)
-  * [Rover](https://docs.px4.io/main/en/frames_rover/)
+* Official Website: http://px4.io (License: BSD 3-clause, [LICENSE](https://github.com/PX4/PX4-Autopilot/blob/master/LICENSE))
+* [Supported airframes](https://docs.px4.io/master/en/airframes/airframe_reference.html) ([portfolio](http://px4.io/#airframes)):
+  * [Multicopters](https://docs.px4.io/master/en/frames_multicopter/)
+  * [Fixed wing](https://docs.px4.io/master/en/frames_plane/)
+  * [VTOL](https://docs.px4.io/master/en/frames_vtol/)
+  * [Autogyro](https://docs.px4.io/master/en/frames_autogyro/)
+  * [Rover](https://docs.px4.io/master/en/frames_rover/)
  * many more experimental types (Blimps, Boats, Submarines, High altitude balloons, etc)
 * Releases: [Downloads](https://github.com/PX4/PX4-Autopilot/releases)


 ## Building a PX4 based drone, rover, boat or robot

-The [PX4 User Guide](https://docs.px4.io/main/en/) explains how to assemble [supported vehicles](https://docs.px4.io/main/en/airframes/airframe_reference.html) and fly drones with PX4.
-See the [forum and chat](https://docs.px4.io/main/en/#getting-help) if you need help!
+The [PX4 User Guide](https://docs.px4.io/master/en/) explains how to assemble [supported vehicles](https://docs.px4.io/master/en/airframes/airframe_reference.html) and fly drones with PX4.
+See the [forum and chat](https://docs.px4.io/master/en/#support) if you need help!


 ## Changing code and contributing

-This [Developer Guide](https://docs.px4.io/main/en/development/development.html) is for software developers who want to modify the flight stack and middleware (e.g. to add new flight modes), hardware integrators who want to support new flight controller boards and peripherals, and anyone who wants to get PX4 working on a new (unsupported) airframe/vehicle.
+This [Developer Guide](https://docs.px4.io/master/en/development/development.html) is for software developers who want to modify the flight stack and middleware (e.g. to add new flight modes), hardware integrators who want to support new flight controller boards and peripherals, and anyone who wants to get PX4 working on a new (unsupported) airframe/vehicle.

-Developers should read the [Guide for Contributions](https://docs.px4.io/main/en/contribute/).
-See the [forum and chat](https://docs.px4.io/main/en/#getting-help) if you need help!
+Developers should read the [Guide for Contributions](https://docs.px4.io/master/en/contribute/).
+See the [forum and chat](https://dev.px4.io/master/en/#support) if you need help!


 ### Weekly Dev Call

-The PX4 Dev Team syncs up on a [weekly dev call](https://docs.px4.io/main/en/contribute/).
+The PX4 Dev Team syncs up on a [weekly dev call](https://dev.px4.io/master/en/contribute/#dev_call).

 > **Note** The dev call is open to all interested developers (not just the core dev team). This is a great opportunity to meet the team and contribute to the ongoing development of the platform. It includes a QA session for newcomers. All regular calls are listed in the [Dronecode calendar](https://www.dronecode.org/calendar/).

@@ -88,43 +88,35 @@ This repository contains code supporting Pixhawk standard boards (best supported
  * FMUv6X and FMUv6U (STM32H7, 2021)
    * Various vendors will provide FMUv6X and FMUv6U based designs Q3/2021
  * FMUv5 and FMUv5X (STM32F7, 2019/20)
-    * [Pixhawk 4 (FMUv5)](https://docs.px4.io/main/en/flight_controller/pixhawk4.html)
-    * [Pixhawk 4 mini (FMUv5)](https://docs.px4.io/main/en/flight_controller/pixhawk4_mini.html)
-    * [CUAV V5+ (FMUv5)](https://docs.px4.io/main/en/flight_controller/cuav_v5_plus.html)
-    * [CUAV V5 nano (FMUv5)](https://docs.px4.io/main/en/flight_controller/cuav_v5_nano.html)
-    * [Auterion Skynode (FMUv5X)](https://docs.auterion.com/skynode)
+    * [Pixhawk 4 (FMUv5)](https://docs.px4.io/master/en/flight_controller/pixhawk4.html)
+    * [Pixhawk 4 mini (FMUv5)](https://docs.px4.io/master/en/flight_controller/pixhawk4_mini.html)
+    * [CUAV V5+ (FMUv5)](https://docs.px4.io/master/en/flight_controller/cuav_v5_plus.html)
+    * [CUAV V5 nano (FMUv5)](https://docs.px4.io/master/en/flight_controller/cuav_v5_nano.html)
+    * [Auterion Skynode (FMUv5X)](https://docs.px4.io/master/en/flight_controller/auterion_skynode.html)
  * FMUv4 (STM32F4, 2015)
-    * [Pixracer](https://docs.px4.io/main/en/flight_controller/pixracer.html)
-    * [Pixhawk 3 Pro](https://docs.px4.io/main/en/flight_controller/pixhawk3_pro.html)
+    * [Pixracer](https://docs.px4.io/master/en/flight_controller/pixracer.html)
+    * [Pixhawk 3 Pro](https://docs.px4.io/master/en/flight_controller/pixhawk3_pro.html)
  * FMUv3 (STM32F4, 2014)
-    * [Pixhawk 2](https://docs.px4.io/main/en/flight_controller/pixhawk-2.html)
-    * [Pixhawk Mini](https://docs.px4.io/main/en/flight_controller/pixhawk_mini.html)
-    * [CUAV Pixhack v3](https://docs.px4.io/main/en/flight_controller/pixhack_v3.html)
+    * [Pixhawk 2](https://docs.px4.io/master/en/flight_controller/pixhawk-2.html)
+    * [Pixhawk Mini](https://docs.px4.io/master/en/flight_controller/pixhawk_mini.html)
+    * [CUAV Pixhack v3](https://docs.px4.io/master/en/flight_controller/pixhack_v3.html)
  * FMUv2 (STM32F4, 2013)
-    * [Pixhawk](https://docs.px4.io/main/en/flight_controller/pixhawk.html)
-    * [Pixfalcon](https://docs.px4.io/main/en/flight_controller/pixfalcon.html)
+    * [Pixhawk](https://docs.px4.io/master/en/flight_controller/pixhawk.html)
+    * [Pixfalcon](https://docs.px4.io/master/en/flight_controller/pixfalcon.html)

 ### Manufacturer and Community supported
-  * [Holybro Durandal](https://docs.px4.io/main/en/flight_controller/durandal.html)
-  * [Hex Cube Orange](https://docs.px4.io/main/en/flight_controller/cubepilot_cube_orange.html)
-  * [Hex Cube Yellow](https://docs.px4.io/main/en/flight_controller/cubepilot_cube_yellow.html)
+  * [Holybro Durandal](https://docs.px4.io/master/en/flight_controller/durandal.html)
+  * [Hex Cube Orange](https://docs.px4.io/master/en/flight_controller/cubepilot_cube_orange.html)
+  * [Hex Cube Yellow](https://docs.px4.io/master/en/flight_controller/cubepilot_cube_yellow.html)
  * [Airmind MindPX V2.8](http://www.mindpx.net/assets/accessories/UserGuide_MindPX.pdf)
  * [Airmind MindRacer V1.2](http://mindpx.net/assets/accessories/mindracer_user_guide_v1.2.pdf)
-  * [Bitcraze Crazyflie 2.0](https://docs.px4.io/main/en/complete_vehicles/crazyflie2.html)
-  * [Omnibus F4 SD](https://docs.px4.io/main/en/flight_controller/omnibus_f4_sd.html)
-  * [Holybro Kakute F7](https://docs.px4.io/main/en/flight_controller/kakutef7.html)
-  * [Raspberry PI with Navio 2](https://docs.px4.io/main/en/flight_controller/raspberry_pi_navio2.html)
+  * [Bitcraze Crazyflie 2.0](https://docs.px4.io/master/en/complete_vehicles/crazyflie2.html)
+  * [Omnibus F4 SD](https://docs.px4.io/master/en/flight_controller/omnibus_f4_sd.html)
+  * [Holybro Kakute F7](https://docs.px4.io/master/en/flight_controller/kakutef7.html)
+  * [Raspberry PI with Navio 2](https://docs.px4.io/master/en/flight_controller/raspberry_pi_navio2.html)

-Additional information about supported hardware can be found in [PX4 user Guide > Autopilot Hardware](https://docs.px4.io/main/en/flight_controller/).
+Additional information about supported hardware can be found in [PX4 user Guide > Autopilot Hardware](https://docs.px4.io/master/en/flight_controller/).

 ## Project Roadmap

 A high level project roadmap is available [here](https://github.com/orgs/PX4/projects/25).
-
-## Project Governance
-
-The PX4 Autopilot project including all of its trademarks is hosted under [Dronecode](https://www.dronecode.org/), part of the Linux Foundation.
-
-<a href="https://www.dronecode.org/" style="padding:20px" ><img src="https://mavlink.io/assets/site/logo_dronecode.png" alt="Dronecode Logo" width="110px"/></a>
-<a href="https://www.linuxfoundation.org/projects" style="padding:20px;"><img src="https://mavlink.io/assets/site/logo_linux_foundation.png" alt="Linux Foundation Logo" width="80px" /></a>
-<div style="padding:10px">&nbsp;</div>
@@ -112,17 +112,23 @@ add_custom_command(
 		${PX4_SOURCE_DIR}/Tools/px4airframes/xmlout.py
 		${PX4_SOURCE_DIR}/Tools/serial/generate_config.py
 	)
+set(romfs_extract_stamp ${CMAKE_CURRENT_BINARY_DIR}/romfs_extract.stamp)
+add_custom_command(
+	OUTPUT ${romfs_extract_stamp}
+	COMMAND ${CMAKE_COMMAND} -E remove_directory ${romfs_gen_root_dir}/*
+	COMMAND ${CMAKE_COMMAND} -E tar xf ${romfs_tar_file}
+	COMMAND ${CMAKE_COMMAND} -E touch ${romfs_extract_stamp}
+	WORKING_DIRECTORY ${romfs_gen_root_dir}
+	DEPENDS ${romfs_tar_file}
+	VERBATIM
+	)

-
-set(romfs_copy_stamp ${CMAKE_CURRENT_BINARY_DIR}/romfs_copy.stamp)
 add_custom_command(
 	OUTPUT
 		${romfs_gen_root_dir}/init.d/rc.serial
 		${romfs_gen_root_dir}/init.d/rc.autostart
 		${romfs_gen_root_dir}/init.d/rc.autostart.post
-		${romfs_copy_stamp}
-	COMMAND ${CMAKE_COMMAND} -E remove_directory ${romfs_gen_root_dir}/*
-	COMMAND ${CMAKE_COMMAND} -E tar xf ${romfs_tar_file}
+		romfs_copy.stamp
 	COMMAND ${PYTHON_EXECUTABLE} ${PX4_SOURCE_DIR}/Tools/px_process_airframes.py
 		--airframes-path ${romfs_gen_root_dir}/init.d
 		--start-script ${romfs_gen_root_dir}/init.d/rc.autostart
@@ -131,9 +137,9 @@ add_custom_command(
 		--rc-dir ${romfs_gen_root_dir}/init.d
 		--serial-ports ${board_serial_ports} ${added_arguments}
 		--config-files ${module_config_files} #--verbose
-	COMMAND ${CMAKE_COMMAND} -E touch ${romfs_copy_stamp}
-	WORKING_DIRECTORY ${romfs_gen_root_dir}
-	DEPENDS ${romfs_tar_file}
+	COMMAND ${CMAKE_COMMAND} -E touch romfs_copy.stamp
+	DEPENDS
+		${romfs_extract_stamp}
 	COMMENT "ROMFS: copying, generating airframes"
 	)

@@ -305,7 +311,7 @@ add_custom_command(OUTPUT romfs_extras.stamp

 add_custom_target(romfs_gen_files_target
 	DEPENDS
-		${romfs_copy_stamp}
+		${romfs_extract_stamp}
 		${romfs_gen_root_dir}/init.d/rc.serial
 		romfs_extras.stamp
 	)
@@ -86,28 +86,10 @@ unset BOARD_RC_SENSORS
 . ${R}etc/init.d/rc.serial

 # Check for flow sensor
-if param compare -s SENS_EN_PX4FLOW 1
+if param compare SENS_EN_PX4FLOW 1
 then
 	px4flow start -X &
 fi

-if param compare -s IMU_GYRO_CAL_EN 1
-then
-	gyro_calibration start
-fi
-
-
-if param compare -s MBE_ENABLE 1
-then
-	# conservative mag bias estimation
-	param set-default MBE_LEARN_GAIN 5
-	param set-default IMU_GYRO_CUTOFF 20
-	mag_bias_estimator start
-fi
-
-param set-default SENS_MAG_RATE 100
-
-sensors start
-
 uavcannode start
 unset R
@@ -1,101 +0,0 @@
-#!/bin/sh
-#
-# @name 6DoF Omnicopter SITL
-#
-# @type Quadrotor Wide
-#
-# @maintainer Jaeyoung Lim <jalim@ethz.ch>
-#
-
-. ${R}etc/init.d/rc.mc_defaults
-
-param set-default SYS_CTRL_ALLOC 1
-
-
-param set-default CA_AIRFRAME 0
-
-param set-default CA_ROTOR_COUNT 8
-param set-default CA_R_REV 255
-
-param set-default CA_ROTOR0_PX 0.14435
-param set-default CA_ROTOR0_PY -0.14435
-param set-default CA_ROTOR0_PZ -0.14435
-param set-default CA_ROTOR0_KM 0.05 # CCW
-param set-default CA_ROTOR0_AX -0.788675
-param set-default CA_ROTOR0_AY -0.211325
-param set-default CA_ROTOR0_AZ -0.57735
-
-param set-default CA_ROTOR1_PX -0.14435
-param set-default CA_ROTOR1_PY -0.14435
-param set-default CA_ROTOR1_PZ -0.14435
-param set-default CA_ROTOR1_KM 0.05
-param set-default CA_ROTOR1_AX 0.211325
-param set-default CA_ROTOR1_AY -0.788675
-param set-default CA_ROTOR1_AZ 0.57735
-
-param set-default CA_ROTOR2_PX 0.14435
-param set-default CA_ROTOR2_PY 0.14435
-param set-default CA_ROTOR2_PZ -0.14435
-param set-default CA_ROTOR2_KM 0.05
-param set-default CA_ROTOR2_AX -0.211325
-param set-default CA_ROTOR2_AY 0.788675
-param set-default CA_ROTOR2_AZ 0.57735
-
-param set-default CA_ROTOR3_PX -0.14435
-param set-default CA_ROTOR3_PY 0.14435
-param set-default CA_ROTOR3_PZ -0.14435
-param set-default CA_ROTOR3_KM 0.05
-param set-default CA_ROTOR3_AX 0.788675
-param set-default CA_ROTOR3_AY 0.211325
-param set-default CA_ROTOR3_AZ -0.57735
-
-param set-default CA_ROTOR4_PX 0.14435
-param set-default CA_ROTOR4_PY -0.14435
-param set-default CA_ROTOR4_PZ 0.14435
-param set-default CA_ROTOR4_KM 0.05
-param set-default CA_ROTOR4_AX 0.788675
-param set-default CA_ROTOR4_AY 0.211325
-param set-default CA_ROTOR4_AZ -0.57735
-
-param set-default CA_ROTOR5_PX -0.14435
-param set-default CA_ROTOR5_PY -0.14435
-param set-default CA_ROTOR5_PZ 0.14435
-param set-default CA_ROTOR5_KM 0.05
-param set-default CA_ROTOR5_AX -0.211325
-param set-default CA_ROTOR5_AY 0.788675
-param set-default CA_ROTOR5_AZ 0.57735
-
-param set-default CA_ROTOR6_PX 0.14435
-param set-default CA_ROTOR6_PY 0.14435
-param set-default CA_ROTOR6_PZ 0.14435
-param set-default CA_ROTOR6_KM 0.05
-param set-default CA_ROTOR6_AX 0.211325
-param set-default CA_ROTOR6_AY -0.788675
-param set-default CA_ROTOR6_AZ 0.57735
-
-param set-default CA_ROTOR7_PX -0.14435
-param set-default CA_ROTOR7_PY 0.14435
-param set-default CA_ROTOR7_PZ 0.14435
-param set-default CA_ROTOR7_KM 0.05
-param set-default CA_ROTOR7_AX -0.788675
-param set-default CA_ROTOR7_AY -0.211325
-param set-default CA_ROTOR7_AZ -0.57735
-
-param set-default PWM_MAIN_FUNC1 101
-param set-default PWM_MAIN_FUNC2 102
-param set-default PWM_MAIN_FUNC3 103
-param set-default PWM_MAIN_FUNC4 104
-param set-default PWM_MAIN_FUNC5 105
-param set-default PWM_MAIN_FUNC6 106
-param set-default PWM_MAIN_FUNC7 107
-param set-default PWM_MAIN_FUNC8 108
-
-# disable MC desaturation which improves attitude tracking
-param set-default CA_METHOD 0
-
-# disable attitude failure detection
-param set-default FD_FAIL_P 0
-param set-default FD_FAIL_R 0
-
-set MIXER skip
-set MIXER_AUX none
@@ -1,23 +0,0 @@
-#!/bin/sh
-#
-# @name QuadrotorX SITL for SIH
-#
-# @type Quadrotor
-#
-# @maintainer Romain Chiappinelli <romain.chiap@gmail.com>
-#
-
-. ${R}etc/init.d/rc.mc_defaults
-
-set MIXER quad_x
-
-# disable some checks to allow to fly:
-# - with usb
-param set-default CBRK_USB_CHK 197848
-# - without real battery
-param set-default CBRK_SUPPLY_CHK 894281
-# - without safety switch
-param set-default COM_PREARM_MODE 0
-param set-default CBRK_IO_SAFETY 22027
-
-param set SIH_VEHICLE_TYPE 0
@@ -1,33 +0,0 @@
-#!/bin/sh
-#
-# @name Plane SITL for SIH
-#
-# @type Plane
-#
-# @maintainer Romain Chiappinelli <romain.chiap@gmail.com>
-
-. ${R}etc/init.d/rc.fw_defaults
-
-set MIXER AERT
-
-# disable some checks to allow to fly:
-# - with usb
-param set-default CBRK_USB_CHK 197848
-# - without real battery
-param set-default CBRK_SUPPLY_CHK 894281
-# - without safety switch
-param set-default COM_PREARM_MODE 0
-param set-default CBRK_IO_SAFETY 22027
-
-param set-default BAT_N_CELLS 3
-
-param set SIH_T_MAX 6.0
-param set SIH_MASS 0.3
-param set SIH_IXX 0.00402
-param set SIH_IYY 0.0144
-param set SIH_IZZ 0.0177
-param set SIH_IXZ 0.00046
-param set SIH_KDV 0.2
-
-param set SIH_VEHICLE_TYPE 1 	# sih as fixed wing
-param set RWTO_TKOFF 1  # enable takeoff from runway (as opposed to launched)
@@ -1,45 +0,0 @@
-#!/bin/sh
-#
-# @name SIH Tailsitter Duo
-#
-# @type VTOL
-#
-# @maintainer Romain Chiappinelli <romain.chiap@gmail.com>
-
-. ${R}etc/init.d/rc.vtol_defaults
-
-param set-default VT_ELEV_MC_LOCK 0
-param set-default VT_TYPE 0
-param set-default VT_FW_DIFTHR_EN 1
-param set-default VT_FW_DIFTHR_SC 0.3
-param set-default MPC_MAN_Y_MAX 60
-param set-default MC_PITCH_P 5
-
-param set-default MAV_TYPE 19
-set MAV_TYPE 19
-set MIXER vtol_tailsitter_duo_sat
-
-# disable some checks to allow to fly:
-# - with usb
-param set-default CBRK_USB_CHK 197848
-# - without real battery
-param set-default CBRK_SUPPLY_CHK 894281
-# - without safety switch
-param set-default COM_PREARM_MODE 0
-param set-default CBRK_IO_SAFETY 22027
-
-param set-default BAT_N_CELLS 3
-
-param set SIH_T_MAX 2.0
-param set SIH_Q_MAX 0.0165
-param set SIH_MASS 0.2
-# IXX and IZZ are inverted from the thesis as the body frame is pitched by 90 deg
-param set SIH_IXX 0.00354
-param set SIH_IYY 0.000625
-param set SIH_IZZ 0.00300
-param set SIH_IXZ 0.0
-param set SIH_KDV 0.2
-param set SIH_L_ROLL 0.145
-
-# sih as tailsitter
-param set SIH_VEHICLE_TYPE 2
@@ -18,7 +18,3 @@ param set-default LPE_FAKE_ORIGIN 1

 param set-default MPC_ALT_MODE 2

-param set-default SENS_FLOW_ROT 6
-param set-default SENS_FLOW_MINHGT 0.7
-param set-default SENS_FLOW_MAXHGT 3.0
-param set-default SENS_FLOW_MAXR 2.5
@@ -9,6 +9,7 @@

 # EKF2
 param set-default EKF2_AID_MASK 2
+param set-default SENS_FLOW_ROT 0

 # LPE: Flow-only mode
 param set-default LPE_FUSION 242
@@ -10,22 +10,26 @@ param set-default EKF2_MAG_YAWLIM 0

 param set-default FW_LND_AIRSPD_SC 1
 param set-default FW_LND_ANG 8
+param set-default FW_THR_LND_MAX 0

 param set-default FW_L1_PERIOD 12

+param set-default FW_MAN_P_MAX 30
+
 param set-default FW_PR_P 0.9
 param set-default FW_PR_FF 0.2
 param set-default FW_PSP_OFF 2
+param set-default FW_P_LIM_MAX 32
 param set-default FW_P_LIM_MIN -15

 param set-default FW_RR_FF 0.1
 param set-default FW_RR_P 0.3

-param set-default FW_SPOILERS_LND 0.4
+param set-default FW_SPOILERS_LND 0.8

 param set-default FW_THR_MAX 0.6
 param set-default FW_THR_MIN 0.05
-param set-default FW_THR_TRIM 0.25
+param set-default FW_THR_CRUISE 0.25

 param set-default FW_T_CLMB_MAX 8
 param set-default FW_T_SINK_MAX 2.7
@@ -7,9 +7,12 @@

 param set-default FW_LND_AIRSPD_SC 1.1
 param set-default FW_LND_ANG 5
+param set-default FW_THR_LND_MAX 0
+param set-default FW_LND_HHDIST 30
 param set-default FW_LND_FL_PMIN 9.5
 param set-default FW_LND_FL_PMAX 20
 param set-default FW_LND_FLALT 5
+param set-default FW_LND_TLALT 15

 param set-default FW_L1_PERIOD 25

@@ -35,6 +38,7 @@ param set-default NAV_DLL_ACT 2
 param set-default RWTO_TKOFF 1

 param set-default RWTO_MAX_PITCH 20
+param set-default RWTO_MAX_ROLL 10

 param set-default RWTO_PSP 8
 param set-default RWTO_AIRSPD_SCL 1.8
@@ -7,9 +7,12 @@

 param set-default FW_LND_AIRSPD_SC 1.1
 param set-default FW_LND_ANG 5
+param set-default FW_THR_LND_MAX 0
+param set-default FW_LND_HHDIST 30
 param set-default FW_LND_FL_PMIN 9.5
 param set-default FW_LND_FL_PMAX 20
 param set-default FW_LND_FLALT 5
+param set-default FW_LND_TLALT 15

 param set-default FW_L1_PERIOD 25

@@ -35,6 +38,7 @@ param set-default NAV_DLL_ACT 2
 param set-default RWTO_TKOFF 1

 param set-default RWTO_MAX_PITCH 20
+param set-default RWTO_MAX_ROLL 10

 param set-default RWTO_PSP 8
 param set-default RWTO_AIRSPD_SCL 1.8
@@ -10,6 +10,7 @@ param set-default EKF2_MAG_YAWLIM 0

 param set-default FW_LND_AIRSPD_SC 1
 param set-default FW_LND_ANG 8
+param set-default FW_THR_LND_MAX 0

 param set-default FW_L1_PERIOD 15

@@ -7,9 +7,12 @@

 param set-default FW_LND_AIRSPD_SC 1.1
 param set-default FW_LND_ANG 5
+param set-default FW_THR_LND_MAX 0
+param set-default FW_LND_HHDIST 30
 param set-default FW_LND_FL_PMIN 9.5
 param set-default FW_LND_FL_PMAX 20
 param set-default FW_LND_FLALT 5
+param set-default FW_LND_TLALT 15

 param set-default FW_L1_PERIOD 25

@@ -34,6 +37,7 @@ param set-default NAV_DLL_ACT 2

 param set-default RWTO_TKOFF 1
 param set-default RWTO_MAX_PITCH 20
+param set-default RWTO_MAX_ROLL 10
 param set-default RWTO_PSP 8
 param set-default RWTO_AIRSPD_SCL 1.8

@@ -10,12 +10,16 @@ param set-default EKF2_MAG_YAWLIM 0

 param set-default FW_LND_AIRSPD_SC 1
 param set-default FW_LND_ANG 8
+param set-default FW_THR_LND_MAX 0

 param set-default FW_L1_PERIOD 12

+param set-default FW_MAN_P_MAX 30
+
 param set-default FW_PR_P 0.9
 param set-default FW_PR_FF 0.2
 param set-default FW_PSP_OFF 2
+param set-default FW_P_LIM_MAX 32
 param set-default FW_P_LIM_MIN -15

 param set-default FW_RR_FF 0.1
@@ -23,7 +27,7 @@ param set-default FW_RR_P 0.3

 param set-default FW_THR_MAX 0.6
 param set-default FW_THR_MIN 0.05
-param set-default FW_THR_TRIM 0.25
+param set-default FW_THR_CRUISE 0.25

 param set-default FW_T_ALT_TC 2
 param set-default FW_T_CLMB_MAX 8
@@ -5,5 +5,5 @@

 . ${R}etc/init.d-posix/airframes/1030_plane

-param set-default FW_THR_TRIM 0.0
+param set-default FW_THR_CRUISE 0.0
 param set-default RWTO_TKOFF 0
@@ -7,11 +7,6 @@

 . ${R}etc/init.d/rc.vtol_defaults

-# TODO: Enable motor failure detection when the
-# VTOL no longer reports 0A for all ESCs in SITL
-param set-default FD_ACT_EN 0
-param set-default FD_ACT_MOT_TOUT 500
-
 # param set-default SYS_CTRL_ALLOC 1
 param set-default CA_AIRFRAME 2

@@ -49,13 +44,15 @@ param set-default PWM_MAIN_FUNC7 202
 param set-default PWM_MAIN_FUNC8 203

 param set-default FW_L1_PERIOD 12
+param set-default FW_MAN_P_MAX 30
 param set-default FW_PR_FF 0.2
 param set-default FW_PR_P 0.9
 param set-default FW_PSP_OFF 2
+param set-default FW_P_LIM_MAX 32
 param set-default FW_P_LIM_MIN -15
 param set-default FW_RR_FF 0.1
 param set-default FW_RR_P 0.3
-param set-default FW_THR_TRIM 0.25
+param set-default FW_THR_CRUISE 0.25
 param set-default FW_THR_MAX 0.6
 param set-default FW_THR_MIN 0.05
 param set-default FW_T_CLMB_MAX 8
@@ -44,12 +44,14 @@ param set-default PWM_MAIN_FUNC7 202
 param set-default PWM_MAIN_REV 96 # invert both elevons

 param set-default FW_L1_PERIOD 12
+param set-default FW_MAN_P_MAX 30
 param set-default FW_PR_I 0.2
 param set-default FW_PR_P 0.2
 param set-default FW_PSP_OFF 2
+param set-default FW_P_LIM_MAX 32
 param set-default FW_P_LIM_MIN -15
 param set-default FW_RR_P 0.2
-param set-default FW_THR_TRIM 0.33
+param set-default FW_THR_CRUISE 0.33
 param set-default FW_THR_MAX 0.6
 param set-default FW_THR_MIN 0.05
 param set-default FW_T_ALT_TC 2
@@ -9,7 +9,7 @@

 param set-default MAV_TYPE 21

-param set-default SYS_CTRL_ALLOC 1
+# param set-default SYS_CTRL_ALLOC 1
 param set-default CA_AIRFRAME 3

 param set-default CA_ROTOR_COUNT 4
@@ -27,7 +27,9 @@ param set-default CA_ROTOR3_PY 0.1875
 param set-default CA_ROTOR3_KM -0.05

 param set-default CA_ROTOR0_TILT 1
+param set-default CA_ROTOR1_TILT 2
 param set-default CA_ROTOR2_TILT 3
+param set-default CA_ROTOR3_TILT 4
 param set-default CA_SV_CS0_TRQ_R -0.5
 param set-default CA_SV_CS0_TYPE 1
 param set-default CA_SV_CS1_TRQ_R 0.5
@@ -54,13 +56,15 @@ param set-default PWM_MAIN_FUNC10 202
 param set-default PWM_MAIN_FUNC11 203

 param set-default FW_L1_PERIOD 12
+param set-default FW_MAN_P_MAX 30
 param set-default FW_PR_FF 0.2
 param set-default FW_PR_P 0.9
 param set-default FW_PSP_OFF 2
+param set-default FW_P_LIM_MAX 32
 param set-default FW_P_LIM_MIN -15
 param set-default FW_RR_FF 0.1
 param set-default FW_RR_P 0.3
-param set-default FW_THR_TRIM 0.38
+param set-default FW_THR_CRUISE 0.38
 param set-default FW_THR_MAX 0.6
 param set-default FW_THR_MIN 0.05
 param set-default FW_T_CLMB_MAX 8
@@ -8,13 +8,15 @@
 . ${R}etc/init.d/rc.vtol_defaults

 param set-default FW_L1_PERIOD 12
+param set-default FW_MAN_P_MAX 30
 param set-default FW_PR_FF 0.2
 param set-default FW_PR_P 0.9
 param set-default FW_PSP_OFF 2
+param set-default FW_P_LIM_MAX 32
 param set-default FW_P_LIM_MIN -15
 param set-default FW_RR_FF 0.1
 param set-default FW_RR_P 0.3
-param set-default FW_THR_TRIM 0.25
+param set-default FW_THR_CRUISE 0.25
 param set-default FW_THR_MAX 0.6
 param set-default FW_THR_MIN 0.05
 param set-default FW_T_ALT_TC 2
@@ -38,9 +38,10 @@ param set-default FW_P_LIM_MAX 25
 param set-default FW_P_LIM_MIN -5
 param set-default FW_R_LIM 30

+param set-default FW_MAN_P_MAX 30.0
 param set-default FW_MAN_R_MAX 30.0

-param set-default FW_THR_TRIM 0.8
+param set-default FW_THR_CRUISE 0.8
 param set-default FW_THR_IDLE 0
 param set-default COM_DISARM_PRFLT 0

@@ -1,54 +0,0 @@
-#!/bin/sh
-#
-# @name ThunderFly TF-G2
-# ThunderFly TF-G2 autogyro airframe. Only for FlightGear simulator
-#
-# @type Autogyro
-# @class Autogyro
-#
-# @url https://github.com/ThunderFly-aerospace/TF-G2/
-#
-#
-
-. ${R}etc/init.d/rc.fw_defaults
-
-param set-default FW_AIRSPD_STALL 5
-
-param set-default FW_P_RMAX_NEG 20.0
-param set-default FW_W_RMAX 10
-param set-default FW_W_EN 1
-
-param set-default FW_RR_P 0.08
-
-param set-default MIS_LTRMIN_ALT 50
-param set-default MIS_TAKEOFF_ALT 7
-
-param set-default NAV_ACC_RAD 20
-param set-default NAV_DLL_ACT 2
-param set-default NAV_LOITER_RAD 50
-
-param set-default RWTO_TKOFF 0
-# Parameters related to autogyro takeoff PR
-#param set-default AG_TKOFF 1
-#param set-default AG_PROT_TYPE 1
-#param set-default AG_PROT_MIN_RPM 50.0
-#param set-default AG_PROT_TRG_RPM 900.0
-#param set-defoult AG_ROTOR_RPM 900.0
-
-param set-default FW_ARSP_SCALE_EN 0
-
-param set-default FW_AIRSPD_MAX 35
-param set-default FW_AIRSPD_MIN 7
-
-param set-default FW_P_LIM_MAX 25
-param set-default FW_P_LIM_MIN -5
-param set-default FW_R_LIM 30
-
-param set-default FW_MAN_R_MAX 30.0
-
-param set-default FW_THR_CRUISE 0.8
-param set-default FW_THR_IDLE 0
-param set-default COM_DISARM_PRFLT 0
-
-set MIXER_FILE etc/mixers-sitl/autogyro_sitl.main.mix
-set MIXER custom
@@ -1,10 +0,0 @@
-#!/bin/sh
-#
-# @name Ignition Gazebo X3
-#
-# @type Quadrotor
-#
-
-. ${R}etc/init.d/rc.mc_defaults
-
-set MIXER quad_w
@@ -1,13 +0,0 @@
-#!/bin/sh
-#
-# @name Ignition Gazebo X4
-#
-# @type Quadrotor
-#
-
-. ${R}etc/init.d/rc.mc_defaults
-
-param set-default MC_PITCHRATE_P 0.1
-param set-default MC_ROLLRATE_P 0.05
-
-set MIXER hexa_x
@@ -1,4 +1,6 @@

+mixer append /dev/pwm_output0 etc/mixers/mount_legs.aux.mix
+
 mavlink start -x -u 14558 -r 4000 -f -m onboard -o 14530 -p

 # shellcheck disable=SC2154
@@ -35,12 +35,8 @@ px4_add_romfs_files(
 	10016_iris
 	10017_iris_ctrlalloc
 	10018_iris_foggy_lidar
-	10019_omnicopter
 	10020_if750a
 	10030_px4vision
-	10040_quadx
-	10041_airplane
-	10042_xvert
 	1010_iris_opt_flow
 	1010_iris_opt_flow.post
 	1011_iris_irlock
@@ -77,14 +73,8 @@ px4_add_romfs_files(
 	1070_boat
 	3010_quadrotor_x
 	3011_hexarotor_x
-
-	4001_x3
-
 	17001_tf-g1
-	17002_tf-g2
 	2507_cloudship
-
-	6001_x4
 	6011_typhoon_h480
 	6011_typhoon_h480.post
 	6012_typhoon_h480_ctrlalloc
@@ -30,12 +30,3 @@ mavlink start -x -u $udp_onboard_payload_port_local -r 4000 -f -m onboard -o $ud

 # Onboard link to gimbal
 mavlink start -x -u $udp_onboard_gimbal_port_local -r 400000 -m gimbal -o $udp_onboard_gimbal_port_remote
-
-# To display for SIH sitl
-if [ "$SIM_MODE" = "sihsim" ]; then
-	udp_sihsim_port_local=$((19450+px4_instance))
-	udp_sihsim_port_remote=$((19410+px4_instance))
-	mavlink start -x -u $udp_sihsim_port_local -r 400000 -m custom -o $udp_sihsim_port_remote
-	mavlink stream -r 200 -s HIL_ACTUATOR_CONTROLS -u  $udp_sihsim_port_local
-	mavlink stream -r 25 -s HIL_STATE_QUATERNION -u  $udp_sihsim_port_local
-fi
@@ -1,33 +1,20 @@
 #!/bin/sh
 # shellcheck disable=SC2154

+simulator_tcp_port=$((4560+px4_instance))

-if ignition_simulator start
-then
-
-	sensor_baro_sim start
-	sensor_gps_sim start
-	sensor_mag_sim start
-
+# Check if PX4_SIM_HOSTNAME environment variable is empty
+# If empty check if PX4_SIM_HOST_ADDR environment variable is empty
+# If both are empty use localhost for simulator
+if [ -z "${PX4_SIM_HOSTNAME}" ]; then
+  if [ -z "${PX4_SIM_HOST_ADDR}" ]; then
+    echo "PX4 SIM HOST: localhost"
+    simulator start -c $simulator_tcp_port
+  else
+    echo "PX4 SIM HOST: $PX4_SIM_HOST_ADDR"
+    simulator start -t $PX4_SIM_HOST_ADDR $simulator_tcp_port
+  fi
 else
-	simulator_tcp_port=$((4560+px4_instance))
-
-	# Check if PX4_SIM_HOSTNAME environment variable is empty
-	# If empty check if PX4_SIM_HOST_ADDR environment variable is empty
-	# If both are empty use localhost for simulator
-	if [ -z "${PX4_SIM_HOSTNAME}" ]; then
-
-		if [ -z "${PX4_SIM_HOST_ADDR}" ]; then
-			echo "PX4 SIM HOST: localhost"
-			simulator start -c $simulator_tcp_port
-		else
-			echo "PX4 SIM HOST: $PX4_SIM_HOST_ADDR"
-			simulator start -t $PX4_SIM_HOST_ADDR $simulator_tcp_port
-		fi
-
-	else
-		echo "PX4 SIM HOST: $PX4_SIM_HOSTNAME"
-		simulator start -h $PX4_SIM_HOSTNAME $simulator_tcp_port
-	fi
-
+  echo "PX4 SIM HOST: $PX4_SIM_HOSTNAME"
+  simulator start -h $PX4_SIM_HOSTNAME $simulator_tcp_port
 fi
@@ -1,6 +1,6 @@
 #!/bin/sh

-#set -e
+set -e

 # PX4 commands need the 'px4-' prefix in bash.
 # (px4-alias.sh is expected to be in the PATH)
@@ -95,9 +95,10 @@ fi

 if param compare SYS_AUTOCONFIG 1
 then
-	# Reset params except Airframe, RC calibration, sensor calibration, flight modes, total flight time, and next flight UUID.
-	param reset_all SYS_AUTOSTART RC* CAL_* COM_FLTMODE* LND_FLIGHT* TC_* COM_FLIGHT*
 	set AUTOCNF yes
+
+	# Wipe out params except RC*, flight modes, total flight time, accel cal, gyro cal, next flight UUID
+	param reset_all SYS_AUTO* RC* COM_FLTMODE* LND_FLIGHT* TC_* CAL_ACC* CAL_GYRO* COM_FLIGHT*
 fi

 # multi-instance setup
@@ -154,8 +155,6 @@ param set-default SDLOG_DIRS_MAX 7

 param set-default TRIG_INTERFACE 3

-param set-default SYS_FAILURE_EN 1
-
 # Adapt timeout parameters if simulation runs faster or slower than realtime.
 if [ -n "$PX4_SIM_SPEED_FACTOR" ]; then
 	COM_DL_LOSS_T_LONGER=$(echo "$PX4_SIM_SPEED_FACTOR * 10" | bc)
@@ -197,6 +196,14 @@ fi

 . "$autostart_file"

+#
+# If autoconfig parameter was set, reset it and save parameters.
+#
+if [ $AUTOCNF = yes ]
+then
+	param set SYS_AUTOCONFIG 0
+fi
+
 # Simulator IMU data provided at 250 Hz
 param set IMU_INTEG_RATE 250

@@ -204,15 +211,11 @@ param set IMU_INTEG_RATE 250
 . px4-rc.params

 dataman start
-# start sih in sih_sim mode, otherwise simulator module
-if [ "$SIM_MODE" = "sihsim" ]; then
-	sih start
 # only start the simulator if not in replay mode, as both control the lockstep time
-elif ! replay tryapplyparams
+if ! replay tryapplyparams
 then
  . px4-rc.simulator
 fi
-
 load_mon start
 battery_simulator start
 tone_alarm start
@@ -29,6 +29,9 @@ param set-default FW_L1_DAMPING 0.74
 param set-default FW_L1_PERIOD 16
 param set-default FW_LND_ANG 15
 param set-default FW_LND_FLALT 5
+param set-default FW_LND_HVIRT 13
+param set-default FW_LND_TLALT 5
+param set-default FW_THR_LND_MAX 0
 param set-default FW_PR_FF 0.35
 param set-default FW_PR_P 0.2
 param set-default FW_RR_FF 0.6
@@ -58,8 +61,6 @@ param set-default HIL_ACT_FUNC6 400

 param set SYS_HITL 1

-param set UAVCAN_ENABLE 0
-
 # disable some checks to allow to fly
 # - with usb
 param set-default CBRK_USB_CHK 197848
@@ -0,0 +1,40 @@
+#!/bin/sh
+#
+# @name Steadidrone QU4D
+#
+# @type Quadrotor Wide
+# @class Copter
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 motor 4
+# @output MAIN5 feed-through of RC AUX1 channel
+# @output MAIN6 feed-through of RC AUX2 channel
+#
+# @output AUX1 feed-through of RC AUX1 channel
+# @output AUX2 feed-through of RC AUX2 channel
+# @output AUX3 feed-through of RC AUX3 channel
+# @output AUX4 feed-through of RC FLAPS channel
+#
+# @maintainer Lorenz Meier <lorenz@px4.io>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+param set-default BAT1_N_CELLS 4
+
+param set-default MC_ROLL_P 7
+param set-default MC_ROLLRATE_P 0.13
+param set-default MC_ROLLRATE_I 0.05
+param set-default MC_ROLLRATE_D 0.004
+param set-default MC_PITCH_P 7
+param set-default MC_PITCHRATE_P 0.19
+param set-default MC_PITCHRATE_I 0.05
+param set-default MC_PITCHRATE_D 0.004
+param set-default MC_YAW_P 4
+
+set MIXER quad_w
@@ -15,8 +15,6 @@ set MIXER quad_x

 param set SYS_HITL 1

-param set UAVCAN_ENABLE 0
-
 param set-default CA_ROTOR_COUNT 4
 param set-default CA_ROTOR0_PX 0.15
 param set-default CA_ROTOR0_PY 0.15
@@ -45,6 +45,7 @@ param set-default MPC_XY_VEL_I_ACC 4
 param set-default MPC_XY_VEL_P_ACC 3
 param set-default MPC_Z_VEL_P_ACC 12
 param set-default MPC_Z_VEL_I_ACC 3
+param set-default MPC_Z_VEL_MAX_DN 1.5

 param set-default NAV_ACC_RAD 5
 param set-default NAV_DLL_ACT 2
@@ -93,8 +94,6 @@ param set-default HIL_ACT_FUNC8 203

 param set SYS_HITL 1

-param set UAVCAN_ENABLE 0
-
 # disable some checks to allow to fly
 # - with usb
 param set-default CBRK_USB_CHK 197848
@@ -0,0 +1,48 @@
+#!/bin/sh
+#
+# @name Steadidrone MAVRIK
+#
+# @type Octo Coax Wide
+# @class Copter
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 motor 4
+# @output MAIN5 motor 5
+# @output MAIN6 motor 6
+# @output MAIN7 motor 7
+# @output MAIN8 motor 8
+#
+# @maintainer Simon Wilks <simon@uaventure.com>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+
+param set-default MC_PITCH_P 4
+param set-default MC_PITCHRATE_P 0.24
+param set-default MC_PITCHRATE_I 0.09
+param set-default MC_PITCHRATE_D 0.013
+param set-default MC_PITCHRATE_MAX 180
+
+param set-default MC_ROLL_P 4
+param set-default MC_ROLLRATE_P 0.16
+param set-default MC_ROLLRATE_I 0.07
+param set-default MC_ROLLRATE_D 0.009
+param set-default MC_ROLLRATE_MAX 180
+
+param set-default MC_YAW_P 3
+
+param set-default MPC_HOLD_MAX_XY 0.25
+param set-default MPC_THR_MIN 0.15
+param set-default MPC_Z_VEL_MAX_DN 2
+
+param set-default BAT1_N_CELLS 4
+
+set MIXER octo_cox_w
+
+set PWM_OUT 12345678
@@ -1,10 +1,22 @@
 #!/bin/sh
 #
-# @name Generic Standard VTOL
+# @name Generic Quadplane VTOL
 #
 # @type Standard VTOL
 # @class VTOL
-
+#
+# @maintainer
+#
+# @output MAIN1 motor 1
+# @output MAIN2 motor 2
+# @output MAIN3 motor 3
+# @output MAIN4 motor 4
+# @output AUX1 Aileron 1
+# @output AUX2 Aileron 2
+# @output AUX3 Elevator
+# @output AUX4 Rudder
+# @output AUX5 Throttle
+#
 # @board px4_fmu-v2 exclude
 # @board bitcraze_crazyflie exclude
 # @board holybro_kakutef7 exclude
@@ -12,21 +24,21 @@

 . ${R}etc/init.d/rc.vtol_defaults

-param set-default SYS_CTRL_ALLOC 1
 param set-default CA_AIRFRAME 2
 param set-default CA_ROTOR_COUNT 5
-param set-default CA_ROTOR0_PX 1
-param set-default CA_ROTOR0_PY 1
-param set-default CA_ROTOR1_PX -1
-param set-default CA_ROTOR1_PY -1
-param set-default CA_ROTOR2_PX 1
-param set-default CA_ROTOR2_PY -1
+param set-default CA_ROTOR0_PX 0.15
+param set-default CA_ROTOR0_PY 0.15
+param set-default CA_ROTOR1_PX -0.15
+param set-default CA_ROTOR1_PY -0.15
+param set-default CA_ROTOR2_PX 0.15
+param set-default CA_ROTOR2_PY -0.15
 param set-default CA_ROTOR2_KM -0.05
-param set-default CA_ROTOR3_PX -1
-param set-default CA_ROTOR3_PY 1
+param set-default CA_ROTOR3_PX -0.15
+param set-default CA_ROTOR3_PY 0.15
 param set-default CA_ROTOR3_KM -0.05
 param set-default CA_ROTOR4_AX 1.0
 param set-default CA_ROTOR4_AZ 0.0
+param set-default CA_ROTOR4_PX 0.2
 param set-default CA_SV_CS_COUNT 4
 param set-default CA_SV_CS0_TYPE 1
 param set-default CA_SV_CS0_TRQ_R -0.5
@@ -36,5 +48,16 @@ param set-default CA_SV_CS2_TYPE 3
 param set-default CA_SV_CS2_TRQ_P 1.0
 param set-default CA_SV_CS3_TRQ_Y 1.0
 param set-default CA_SV_CS3_TYPE 4
+
+param set-default PWM_AUX_DIS5 950
+
 param set-default VT_TYPE 2
+param set-default VT_MOT_ID 1234
+param set-default VT_FW_MOT_OFFID 1234
+
 param set-default MAV_TYPE 22
+
+set MIXER quad_x
+set MIXER_AUX vtol_AAERT
+
+set PWM_OUT 1234
@@ -43,7 +43,7 @@ param set-default MPC_YAWRAUTO_MAX 40
 param set-default FW_PR_I 0.02
 param set-default FW_RR_FF 0.6
 param set-default FW_RR_I 0.01
-param set-default FW_THR_TRIM 0.75
+param set-default FW_THR_CRUISE 0.75

 param set-default VT_ARSP_BLEND 6
 param set-default VT_ARSP_TRANS 12
@@ -14,7 +14,7 @@
 . ${R}etc/init.d/rc.vtol_defaults


-param set-default FW_THR_TRIM 65
+param set-default FW_THR_CRUISE 65
 param set-default FW_RR_FF 0.6

 param set-default MIS_YAW_TMT 10
@@ -31,6 +31,7 @@ param set-default MC_YAWRATE_I 0.04
 param set-default MC_YAWRATE_MAX 40

 param set-default MPC_ACC_HOR_MAX 2
+param set-default MPC_Z_VEL_MAX_DN 1.5
 param set-default MPC_LAND_SPEED 0.8
 param set-default MPC_YAWRAUTO_MAX 40

@@ -0,0 +1,37 @@
+#!/bin/sh
+#
+# @name CruiseAder Claire
+#
+# @type VTOL Tiltrotor
+# @class VTOL
+#
+# @maintainer Samay Siga <samay_s@icloud.com>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.vtol_defaults
+
+param set-default MAV_TYPE 21
+
+param set-default PWM_AUX_DISARM 1000
+param set-default PWM_AUX_MAX 2000
+param set-default PWM_AUX_MIN 1000
+param set-default PWM_AUX_RATE 50
+
+param set-default PWM_MAIN_MAX 2000
+
+param set-default VT_MOT_ID 1234
+param set-default VT_FW_MOT_OFFID 13
+param set-default VT_IDLE_PWM_MC 1080
+param set-default VT_TILT_FW 0.9
+param set-default VT_TILT_MC 0.08
+param set-default VT_TILT_TRANS 0.5
+param set-default VT_ELEV_MC_LOCK 0
+param set-default VT_TYPE 1
+
+set MIXER claire
+set MIXER_AUX claire
+
+set PWM_OUT 1234
@@ -34,6 +34,8 @@ param set-default FW_ACRO_X_MAX   270
 param set-default FW_ACRO_Y_MAX   270
 param set-default FW_ACRO_Z_MAX   180
 param set-default FW_PSP_OFF  5
+param set-default FW_P_LIM_MAX    30
+param set-default FW_P_LIM_MIN    -30
 param set-default FW_RR_FF    0.33
 param set-default FW_RR_P 0.11

@@ -67,9 +69,4 @@ param set-default VT_TYPE 1

 set MIXER vtol_convergence

-if ! ver hwcmp MATEK_H743
-then
-	set PWM_OUT 1234
-else
-	set PWM_OUT 3456
-fi
+set PWM_OUT 1234
@@ -53,8 +53,9 @@ param set-default FW_T_CLMB_MAX 3
 param set-default FW_T_SINK_MAX 3
 param set-default FW_T_SINK_MIN 1
 param set-default FW_T_VERT_ACC 6
-param set-default FW_THR_TRIM 0.70
+param set-default FW_THR_CRUISE 0.70
 param set-default FW_THR_SLEW_MAX 1
+param set-default FW_MAN_P_MAX 30
 param set-default FW_P_LIM_MAX 15
 param set-default FW_P_LIM_MIN -25
 param set-default FW_P_RMAX_NEG 45
@@ -89,6 +90,7 @@ param set-default MPC_ACC_HOR_MAX 2
 param set-default MPC_LAND_SPEED 1.2
 param set-default MPC_TILTMAX_LND 35
 param set-default MPC_Z_VEL_MAX_UP 1.5
+param set-default MPC_Z_VEL_MAX_DN 1.5
 param set-default MPC_HOLD_MAX_XY 0.5
 param set-default MPC_HOLD_MAX_Z 0.5
 param set-default MPC_TKO_RAMP_T 0.8
@@ -129,6 +131,7 @@ param set-default VT_F_TRANS_DUR 1
 param set-default VT_IDLE_PWM_MC 1025
 param set-default VT_B_REV_OUT 0.5
 param set-default VT_B_TRANS_THR 0.7
+param set-default VT_FW_PERM_STAB 1
 param set-default VT_TRANS_TIMEOUT 22
 param set-default VT_F_TRANS_RAMP 4

@@ -31,6 +31,7 @@ param set-default FW_AIRSPD_MAX 30
 param set-default FW_AIRSPD_MIN 19
 param set-default FW_AIRSPD_TRIM 23
 param set-default FW_L1_R_SLEW_MAX 40
+param set-default FW_MAN_P_MAX 30
 param set-default FW_PSP_OFF 3
 param set-default FW_P_LIM_MAX 18
 param set-default FW_P_LIM_MIN -25
@@ -38,7 +39,7 @@ param set-default FW_RLL_TO_YAW_FF 0.1
 param set-default FW_RR_P 0.08
 param set-default FW_R_LIM 45
 param set-default FW_R_RMAX 50
-param set-default FW_THR_TRIM 0.65
+param set-default FW_THR_CRUISE 0.65
 param set-default FW_THR_MIN 0.3
 param set-default FW_THR_SLEW_MAX 0.6
 param set-default FW_T_HRATE_FF 0
@@ -61,7 +62,7 @@ param set-default MPC_JERK_AUTO 4
 param set-default MPC_LAND_SPEED 1
 param set-default MPC_MAN_TILT_MAX 25
 param set-default MPC_MAN_Y_MAX 40
-param set-default COM_SPOOLUP_TIME 1.5
+param set-default MPC_SPOOLUP_TIME 1.5
 param set-default MPC_THR_HOVER 0.45
 param set-default MPC_TILTMAX_AIR 25
 param set-default MPC_TKO_RAMP_T 1.8
@@ -70,6 +71,7 @@ param set-default MPC_VEL_MANUAL 3
 param set-default MPC_XY_CRUISE 3
 param set-default MPC_XY_VEL_MAX 3.5
 param set-default MPC_YAWRAUTO_MAX 40
+param set-default MPC_Z_VEL_MAX_DN 1.5
 param set-default MPC_Z_VEL_MAX_UP 2

 param set-default NAV_ACC_RAD 3
@@ -1,44 +0,0 @@
-#!/bin/sh
-#
-# @name Generic Tiltrotor VTOL
-#
-# @type VTOL Tiltrotor
-# @class VTOL
-#
-# @board px4_fmu-v2 exclude
-# @board bitcraze_crazyflie exclude
-#
-
-. ${R}etc/init.d/rc.vtol_defaults
-
-param set-default SYS_CTRL_ALLOC 1
-
-param set-default CA_AIRFRAME 3
-param set-default CA_ROTOR_COUNT 4
-param set-default CA_ROTOR0_PX 1
-param set-default CA_ROTOR0_PY 1
-param set-default CA_ROTOR0_TILT 2
-param set-default CA_ROTOR1_PX -1
-param set-default CA_ROTOR1_PY -1
-param set-default CA_ROTOR2_PX 1
-param set-default CA_ROTOR2_PY -1
-param set-default CA_ROTOR2_TILT 1
-param set-default CA_ROTOR2_KM -0.05
-param set-default CA_ROTOR3_PX -1
-param set-default CA_ROTOR3_PY 1
-param set-default CA_ROTOR3_KM -0.05
-param set-default CA_SV_CS_COUNT 4
-param set-default CA_SV_CS0_TYPE 1
-param set-default CA_SV_CS0_TRQ_R -0.5
-param set-default CA_SV_CS1_TYPE 2
-param set-default CA_SV_CS1_TRQ_R 0.5
-param set-default CA_SV_CS2_TYPE 7
-param set-default CA_SV_CS2_TRQ_P 0.5
-param set-default CA_SV_CS2_TRQ_Y 0.5
-param set-default CA_SV_CS3_TYPE 8
-param set-default CA_SV_CS3_TRQ_P 0.5
-param set-default CA_SV_CS3_TRQ_Y -0.5
-param set-default CA_SV_TL_COUNT 2
-
-param set-default MAV_TYPE 21
-param set-default VT_TYPE 1
@@ -1,10 +1,17 @@
 #!/bin/sh
 #
-# @name Generic VTOL Tailsitter
+# @name Generic Tailsitter
 #
-# @type VTOL Tailsitter
+# @type VTOL Duo Tailsitter
 # @class VTOL
 #
+# @output MAIN1 motor right
+# @output MAIN2 motor left
+# @output MAIN5 elevon right
+# @output MAIN6 elevon left
+#
+# @maintainer Roman Bapst <roman@px4.io>
+#
 # @board px4_fmu-v2 exclude
 # @board bitcraze_crazyflie exclude
 # @board holybro_kakutef7 exclude
@@ -12,13 +19,18 @@

 . ${R}etc/init.d/rc.vtol_defaults

-param set-default SYS_CTRL_ALLOC 1
+param set-default MAV_TYPE 19
+
+param set-default VT_ELEV_MC_LOCK 0
+param set-default VT_MOT_COUNT 2
+param set-default VT_TYPE 0
+
 param set-default CA_AIRFRAME 4
 param set-default CA_ROTOR_COUNT 2
 param set-default CA_ROTOR0_KM -0.05
-param set-default CA_ROTOR0_PY -0.2
-param set-default CA_ROTOR1_KM 0.05
-param set-default CA_ROTOR1_PY 0.2
+param set-default CA_ROTOR0_PY 0.2
+param set-default CA_ROTOR1_KM -0.05
+param set-default CA_ROTOR1_PY -0.2
 param set-default CA_SV_CS_COUNT 2
 param set-default CA_SV_CS0_TRQ_P 0.5
 param set-default CA_SV_CS0_TRQ_Y 0.5
@@ -27,6 +39,6 @@ param set-default CA_SV_CS1_TRQ_P 0.5
 param set-default CA_SV_CS1_TRQ_Y -0.5
 param set-default CA_SV_CS1_TYPE 6

-param set-default MAV_TYPE 19
-param set-default VT_TYPE 0
-param set-default VT_ELEV_MC_LOCK 0
+set MIXER vtol_tailsitter_duo
+
+set PWM_OUT 1234
@@ -37,7 +37,7 @@ param set-default SENS_BOARD_ROT 8
 param set-default FW_AIRSPD_MAX 20
 param set-default FW_AIRSPD_MIN 7
 param set-default FW_AIRSPD_TRIM 13
-param set-default FW_THR_TRIM 0.8
+param set-default FW_THR_CRUISE 0.8

 param set-default FW_MAN_P_MAX 25
 param set-default FW_MAN_R_MAX 25
@@ -32,7 +32,7 @@ param set-default SENS_BOARD_ROT 4
 param set-default FW_AIRSPD_MAX 20
 param set-default FW_AIRSPD_MIN 7
 param set-default FW_AIRSPD_TRIM 13
-param set-default FW_THR_TRIM 0.8
+param set-default FW_THR_CRUISE 0.8

 param set-default FW_MAN_P_MAX 25
 param set-default FW_MAN_R_MAX 25
@@ -1,16 +1,28 @@
 #!/bin/sh
 #
-# @name Generic Standard Plane
+# @name Standard Plane
 #
 # @type Standard Plane
 # @class Plane
 #
+# @output MAIN1 aileron
+# @output MAIN2 elevator
+# @output MAIN3 throttle
+# @output MAIN4 rudder
+# @output MAIN5 flaps
+# @output MAIN6 gear
+#
+# @output AUX1 feed-through of RC AUX1 channel
+# @output AUX2 feed-through of RC AUX2 channel
+# @output AUX3 feed-through of RC AUX3 channel
+#
+# @maintainer Lorenz Meier <lorenz@px4.io>
+#
 # @board bitcraze_crazyflie exclude
 #

 . ${R}etc/init.d/rc.fw_defaults

-param set-default SYS_CTRL_ALLOC 1
 param set-default CA_AIRFRAME 1
 param set-default CA_ROTOR_COUNT 1
 param set-default CA_ROTOR0_PX 0.3
@@ -22,3 +34,11 @@ param set-default CA_SV_CS2_TRQ_P 1.0
 param set-default CA_SV_CS2_TYPE 3
 param set-default CA_SV_CS3_TRQ_Y 1.0
 param set-default CA_SV_CS3_TYPE 4
+
+param set-default PWM_AUX_RATE 50
+param set-default PWM_MAIN_RATE 50
+
+set MIXER AETRFG
+
+# Rate must be set by group (see pwm info).
+# Throttle is in the same group as servos.
@@ -5,20 +5,19 @@
 # @type Flying Wing
 # @class Plane
 #
+# @output MAIN1 left aileron
+# @output MAIN2 right aileron
+# @output MAIN4 throttle
+#
+# @output AUX1 feed-through of RC AUX1 channel
+# @output AUX2 feed-through of RC AUX2 channel
+# @output AUX3 feed-through of RC AUX3 channel
+#
+# @maintainer
+#
 # @board bitcraze_crazyflie exclude
 #

 . ${R}etc/init.d/rc.fw_defaults

-param set-default SYS_CTRL_ALLOC 1
-param set-default CA_AIRFRAME 1
-
-param set-default CA_ROTOR_COUNT 1
-param set-default CA_ROTOR0_PX 0.15
-param set-default CA_SV_CS_COUNT 2
-param set-default CA_SV_CS0_TYPE 5
-param set-default CA_SV_CS0_TRQ_P 0.5
-param set-default CA_SV_CS0_TRQ_R -0.5
-param set-default CA_SV_CS1_TYPE 6
-param set-default CA_SV_CS1_TRQ_P 0.5
-param set-default CA_SV_CS1_TRQ_R 0.5
+set MIXER fw_generic_wing
@@ -0,0 +1,45 @@
+#!/bin/sh
+#
+# @name IO Camflyer
+#
+# @type Flying Wing
+# @class Plane
+#
+# @output MAIN1 left aileron
+# @output MAIN2 right aileron
+# @output MAIN4 throttle
+#
+# @output AUX1 feed-through of RC AUX1 channel
+# @output AUX2 feed-through of RC AUX2 channel
+# @output AUX3 feed-through of RC AUX3 channel
+#
+# @maintainer Simon Wilks <simon@uaventure.com>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.fw_defaults
+
+param set-default FW_AIRSPD_MAX 15
+param set-default FW_AIRSPD_TRIM 13
+param set-default FW_R_TC 0.3
+param set-default FW_P_TC 0.3
+param set-default FW_L1_DAMPING 0.74
+param set-default FW_L1_PERIOD 16
+param set-default FW_LND_ANG 15
+param set-default FW_LND_FLALT 5
+param set-default FW_LND_HVIRT 13
+param set-default FW_LND_TLALT 5
+param set-default FW_THR_LND_MAX 0
+param set-default FW_PR_FF 0.35
+param set-default FW_RR_FF 0.6
+param set-default FW_RR_P 0.04
+
+param set-default PWM_MAIN_DISARM 1000
+
+
+set MIXER fw_generic_wing
+
+# Provide ESC a constant 1000 us pulse while disarmed
+set PWM_OUT 4
@@ -2,7 +2,7 @@
 #
 # @name Phantom FPV Flying Wing
 #
-# @url https://docs.px4.io/main/en/frames_plane/wing_wing_z84.html
+# @url https://docs.px4.io/master/en/frames_plane/wing_wing_z84.html
 #
 # @type Flying Wing
 # @class Plane
@@ -30,6 +30,9 @@ param set-default FW_L1_DAMPING 0.74
 param set-default FW_L1_PERIOD 16
 param set-default FW_LND_ANG 15
 param set-default FW_LND_FLALT 5
+param set-default FW_LND_HVIRT 13
+param set-default FW_LND_TLALT 5
+param set-default FW_THR_LND_MAX 0
 param set-default FW_PR_FF 0.35
 param set-default FW_RR_FF 0.6
 param set-default FW_RR_P 0.04
@@ -2,7 +2,7 @@
 #
 # @name Wing Wing (aka Z-84) Flying Wing
 #
-# @url https://docs.px4.io/main/en/frames_plane/wing_wing_z84.html
+# @url https://docs.px4.io/master/en/frames_plane/wing_wing_z84.html
 #
 # @type Flying Wing
 # @class Plane
@@ -32,6 +32,9 @@ param set-default FW_L1_DAMPING 0.74
 param set-default FW_L1_PERIOD 16
 param set-default FW_LND_ANG 15
 param set-default FW_LND_FLALT 5
+param set-default FW_LND_HVIRT 13
+param set-default FW_LND_TLALT 5
+param set-default FW_THR_LND_MAX 0
 param set-default FW_PR_FF 0.35
 param set-default FW_RR_FF 0.6
 param set-default FW_RR_P 0.04
@@ -0,0 +1,29 @@
+#!/bin/sh
+#
+# @name FX-79 Buffalo Flying Wing
+#
+# @type Flying Wing
+# @class Plane
+#
+# @output MAIN1 right aileron
+# @output MAIN2 left aileron
+# @output MAIN4 throttle
+#
+# @output AUX1 feed-through of RC AUX1 channel
+# @output AUX2 feed-through of RC AUX2 channel
+# @output AUX3 feed-through of RC AUX3 channel
+#
+# @maintainer Simon Wilks <simon@uaventure.com>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.fw_defaults
+
+param set-default FW_AIRSPD_MAX 30
+param set-default FW_AIRSPD_MIN 13
+
+param set-default NAV_LOITER_RAD 150
+
+set MIXER fw_generic_wing
@@ -0,0 +1,23 @@
+#!/bin/sh
+#
+# @name Viper
+#
+# @type Flying Wing
+# @class Plane
+# @output MAIN1 left aileron
+# @output MAIN2 right aileron
+# @output MAIN4 throttle
+#
+# @output AUX1 feed-through of RC AUX1 channel
+# @output AUX2 feed-through of RC AUX2 channel
+# @output AUX3 feed-through of RC AUX3 channel
+#
+# @maintainer Simon Wilks <simon@uaventure.com>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.fw_defaults
+
+set MIXER Viper
@@ -0,0 +1,53 @@
+#!/bin/sh
+#
+# @name Modified Parrot Disco
+#
+# @url
+#
+# @type Flying Wing
+# @class Plane
+#
+# @output MAIN1 left aileron
+# @output MAIN2 right aileron
+# @output MAIN4 throttle
+#
+# @output AUX1 feed-through of RC AUX1 channel
+# @output AUX2 feed-through of RC AUX2 channel
+# @output AUX3 feed-through of RC AUX3 channel
+#
+# @maintainer Jan Liphardt <JTLiphardt@gmail.com>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.fw_defaults
+
+####################################
+# Airspeed
+####################################
+param set-default FW_AIRSPD_MAX  27 # = 52 knots
+
+####################################
+# Pitch
+####################################
+
+# Pitch rate feed forward (def = 0.5 %/rad/sec)
+param set-default FW_PR_FF 0.35
+
+####################################
+# Roll
+####################################
+
+# Basic limits (def = 50 deg)
+param set-default FW_R_LIM 40
+
+# Roll rate upper limit (def = 70 deg/s)
+param set-default FW_R_RMAX 50
+
+param set-default PWM_MAIN_DISARM 1000
+
+set MIXER fw_generic_wing.main.mix
+
+# Provide ESC a constant 1000 us pulse
+set PWM_OUT 4
@@ -27,7 +27,11 @@ param set-default FW_AIRSPD_TRIM 16.5
 param set-default FW_L1_PERIOD 15
 param set-default FW_LND_ANG 15
 param set-default FW_LND_FLALT 8
+param set-default FW_LND_HVIRT 13
+param set-default FW_LND_TLALT 10
+param set-default FW_THR_LND_MAX 0
 param set-default FW_P_LIM_MAX 20
+param set-default FW_P_LIM_MIN -30
 param set-default FW_R_LIM 45
 param set-default FW_PR_FF 0.45
 param set-default FW_PR_P 0.005
@@ -36,7 +40,7 @@ param set-default FW_RR_P 0.013
 param set-default FW_P_RMAX_NEG 70
 param set-default FW_P_RMAX_POS 70
 param set-default FW_R_RMAX 70
-param set-default FW_THR_TRIM 0.55
+param set-default FW_THR_CRUISE 0.55

 param set-default LNDFW_AIRSPD_MAX 6
 param set-default LNDFW_XYACC_MAX 4
@@ -0,0 +1,21 @@
+#!/bin/sh
+#
+# @name DJI F330 w/ DJI ESCs
+#
+# @type Quadrotor x
+# @class Copter
+#
+# @maintainer Lorenz Meier <lorenz@px4.io>
+# @board px4_fmu-v2 exclude
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+param set-default MC_ROLL_P 7
+param set-default MC_ROLLRATE_I 0.05
+param set-default MC_PITCH_P 7
+param set-default MC_PITCHRATE_I 0.05
+
+
+# DJI ESCs do not support calibration and need a higher min
+param set-default PWM_MAIN_MIN 1230
@@ -0,0 +1,20 @@
+#!/bin/sh
+#
+# @name DJI F450 w/ DJI ESCs
+#
+# @type Quadrotor x
+# @class Copter
+#
+# @maintainer Lorenz Meier <lorenz@px4.io>
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+param set-default MC_ROLL_P 7
+param set-default MC_ROLLRATE_I 0.05
+param set-default MC_PITCH_P 7
+param set-default MC_PITCHRATE_I 0.05
+param set-default MC_YAWRATE_P 0.3
+
+# DJI ESCs do not support calibration and need a higher min
+param set-default PWM_MAIN_MIN 1230
@@ -104,6 +104,7 @@ param set-default SDLOG_PROFILE 131
 param set-default SENS_CM8JL65_CFG 104
 param set-default SENS_FLOW_MAXHGT 25
 param set-default SENS_FLOW_MINHGT 0.5
+param set-default SENS_FLOW_ROT 0
 param set-default IMU_GYRO_CUTOFF 100
 param set-default SENS_EN_PMW3901 1

@@ -1,7 +1,7 @@
 #!/bin/sh
 #
 # @name Spedix S250AQ
-# @url https://docs.px4.io/main/en/frames_multicopter/spedix_s250_pixracer.html
+# @url https://docs.px4.io/master/en/frames_multicopter/spedix_s250_pixracer.html
 #
 # @type Quadrotor asymmetric
 # @class Copter
@@ -2,7 +2,7 @@
 #
 # @name HolyBro QAV250
 #
-# @url https://docs.px4.io/main/en/frames_multicopter/holybro_qav250_pixhawk4_mini.html
+# @url https://docs.px4.io/master/en/frames_multicopter/holybro_qav250_pixhawk4_mini.html
 #
 # @type Quadrotor x
 # @class Copter
@@ -0,0 +1,27 @@
+#!/bin/sh
+#
+# @name DJI Matrice 100
+#
+# @type Quadrotor x
+# @class Copter
+#
+# @maintainer James Goppert <james.goppert@gmail.com>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+param set-default BAT1_N_CELLS 6
+
+param set-default MC_ROLLRATE_P 0.05
+param set-default MC_ROLLRATE_I 0.05
+param set-default MC_ROLLRATE_D 0.001
+param set-default MC_PITCHRATE_P 0.05
+param set-default MC_PITCHRATE_I 0.05
+param set-default MC_PITCHRATE_D 0.001
+
+param set-default MC_YAWRATE_I 0
+
+param set-default PWM_MAIN_MIN 1200
@@ -47,7 +47,6 @@ param set-default COM_RC_LOSS_T 3

 # ekf2
 param set-default EKF2_AID_MASK 33
-param set-default EKF2_TERR_MASK 1
 param set-default EKF2_BARO_DELAY 0
 param set-default EKF2_BARO_NOISE 2.0

@@ -174,7 +173,7 @@ param set-default RC1_TRIM          1000
 param set-default SENS_FLOW_MAXR   7.4
 param set-default SENS_FLOW_MINHGT 0.15
 param set-default SENS_FLOW_MAXHGT 5.0
-param set-default SENS_FLOW_ROT 0
+param set-default SENS_FLOW_ROT    0

 # ignore the SD card errors and use normal startup sound
 set STARTUP_TUNE "1"
@@ -52,16 +52,22 @@ px4_add_romfs_files(

 	# [3000, 3999] Flying wing"
 	3000_generic_wing
+	3030_io_camflyer
 	3031_phantom
 	3032_skywalker_x5
 	3033_wingwing
+	3034_fx79
+	3035_viper
 	3036_pigeon
+	3037_parrot_disco_mod
 	3100_tbs_caipirinha

 	# [4000, 4999] Quadrotor x"
 	4001_quad_x
 	4003_qavr5
 	4009_qav250
+	4010_dji_f330
+	4011_dji_f450
 	4014_s500
 	4015_holybro_s500
 	4016_holybro_px4vision
@@ -75,6 +81,7 @@ px4_add_romfs_files(
 	4051_s250aq
 	4052_holybro_qav250
 	4053_holybro_kopis2
+	4060_dji_matrice_100
 	4061_atl_mantis_edu
 	4071_ifo
 	4072_draco
@@ -105,6 +112,7 @@ px4_add_romfs_files(
 	# [10000, 10999] Quadrotor Wide arm / H frame"
 	10015_tbs_discovery
 	10016_3dr_iris
+	10017_steadidrone_qu4d
 	10018_tbs_endurance

 	# [11000, 11999] Hexa Cox
@@ -112,6 +120,7 @@ px4_add_romfs_files(

 	# [12000, 12999] Octo Cox
 	12001_octo_cox
+	12002_steadidrone_mavrik

 	# [13000, 13999] VTOL
 	13000_generic_vtol_standard
@@ -124,7 +133,7 @@ px4_add_romfs_files(
 	13007_vtol_AAVVT_quad
 	13008_QuadRanger
 	13009_vtol_spt_ranger
-	13100_generic_vtol_tiltrotor
+	13010_claire
 	13012_convergence
 	13013_deltaquad
 	13014_vtol_babyshark
@@ -21,20 +21,16 @@ param set-default HTE_VXY_THR 2.0
 param set-default MIS_DIST_WPS 5000

 param set-default MPC_ACC_HOR_MAX 2
-param set-default MPC_VEL_MANUAL 5
-param set-default MPC_XY_CRUISE 5
+param set-default MPC_TKO_SPEED 1
+param set-default MPC_VEL_MANUAL 3
+param set-default MPC_XY_CRUISE 3
 param set-default MPC_XY_ERR_MAX 5
-param set-default MPC_XY_VEL_MAX 8
+param set-default MPC_XY_VEL_MAX 4
+param set-default MPC_Z_VEL_MAX_DN 1.5
 param set-default MPC_JERK_MAX 4.5
 param set-default MPC_YAW_MODE 4

-# reduce aggressiveness around roll and yaw axis,
-# as VTOLs usually have high intertia and lot af drag due to wings
-param set-default MC_ROLL_P 5
-param set-default MC_ROLLRATE_MAX 120
-param set-default MC_YAW_P 2
-param set-default MC_YAWRATE_MAX 120
-param set-default MPC_MAN_Y_MAX 90
+param set-default NAV_ACC_RAD 3

 param set-default PWM_AUX_RATE 50
 param set-default PWM_MAIN_RATE 400
@@ -21,6 +21,7 @@ set +e
 # it wastes flash
 #
 set R /
+set AUTOCNF no
 set FCONFIG /fs/microsd/etc/config.txt
 set FEXTRAS /fs/microsd/etc/extras.txt
 set FRC /fs/microsd/etc/rc.txt
@@ -176,12 +177,13 @@ else
 	fi

 	#
-	# If the airframe has been previously reset SYS_AUTCONFIG will have been set to 1 and other params will be reset on the next boot.
+	# Set AUTOCNF flag to use it in AUTOSTART scripts.
 	#
 	if param greater SYS_AUTOCONFIG 0
 	then
-		# Reset params except Airframe, RC calibration, sensor calibration, flight modes, total flight time, and next flight UUID.
-		param reset_all SYS_AUTOSTART RC* CAL_* COM_FLTMODE* LND_FLIGHT* TC_* COM_FLIGHT*
+		# Wipe out params except RC*, flight modes, total flight time, calibration parameters, next flight UUID
+		param reset_all SYS_AUTO* RC* COM_FLTMODE* LND_FLIGHT* TC_* CAL_ACC* CAL_GYRO* COM_FLIGHT*
+		set AUTOCNF yes
 	fi

 	#
@@ -206,26 +208,6 @@ else
 	fi
 	unset BOARD_RC_DEFAULTS

-	#
-	# Set parameters and env variables for selected SYS_AUTOSTART.
-	#
-	set AUTOSTART_PATH etc/init.d/rc.autostart
-	if ! param compare SYS_AUTOSTART 0
-	then
-		if param greater SYS_AUTOSTART 1000000
-		then
-			# Use external startup file
-			if [ $SDCARD_AVAILABLE = yes ]
-			then
-				set AUTOSTART_PATH etc/init.d/rc.autostart_ext
-			else
-				echo "ERROR [init] SD card not mounted - trying to load airframe from ROMFS"
-			fi
-		fi
-		. ${R}$AUTOSTART_PATH
-	fi
-	unset AUTOSTART_PATH
-
 	#
 	# Start the tone_alarm driver.
 	# Needs to be started after the parameters are loaded (for CBRK_BUZZER).
@@ -263,6 +245,26 @@ else
 	rgbled start -X -q
 	rgbled_ncp5623c start -X -q

+	#
+	# Set parameters and env variables for selected AUTOSTART.
+	#
+	set AUTOSTART_PATH etc/init.d/rc.autostart
+	if ! param compare SYS_AUTOSTART 0
+	then
+		if param greater SYS_AUTOSTART 1000000
+		then
+			# Use external startup file
+			if [ $SDCARD_AVAILABLE = yes ]
+			then
+				set AUTOSTART_PATH etc/init.d/rc.autostart_ext
+			else
+				echo "ERROR [init] SD card not mounted - trying to load airframe from ROMFS"
+			fi
+		fi
+		. ${R}$AUTOSTART_PATH
+	fi
+	unset AUTOSTART_PATH
+
 	#
 	# Override parameters from user configuration file.
 	#
@@ -272,6 +274,14 @@ else
 		. $FCONFIG
 	fi

+	#
+	# If autoconfig parameter was set, reset it and save parameters.
+	#
+	if [ $AUTOCNF = yes ]
+	then
+		param set SYS_AUTOCONFIG 0
+	fi
+
 	#
 	# Check if UAVCAN is enabled, default to it for ESCs.
 	#
@@ -288,9 +298,9 @@ else
 			tune_control play error
 		fi
 	else
-		if param greater -s CYPHAL_ENABLE 0
+		if param greater -s UAVCAN_V1_ENABLE 0
 		then
-			cyphal start
+			uavcan_v1 start
 		fi
 	fi

@@ -303,7 +313,7 @@ else
 	then
 		# Check for the mini using build with px4io fw file
 		# but not a px4IO
-		if ver hwtypecmp V5004000 V5006000
+		if ver hwtypecmp V540 V560
 		then
 			param set SYS_USE_IO 0
 		else
@@ -555,6 +565,7 @@ fi
 # Unset all script parameters to free RAM.
 #
 unset R
+unset AUTOCNF
 unset FCONFIG
 unset FEXTRAS
 unset FRC
@@ -40,6 +40,8 @@ px4_add_romfs_files(
 	babyshark.main.mix
 	blade130.main.mix
 	CCPM.main.mix
+	claire.aux.mix
+	claire.main.mix
 	cloudship.main.mix
 	coax.main.mix
 	delta.main.mix
@@ -81,6 +83,7 @@ px4_add_romfs_files(
 	tri_y_yaw-.main.mix
 	uuv_x.main.mix
 	vectored6dof.main.mix
+	Viper.main.mix
 	vtol_AAERT.aux.mix
 	vtol_AAVVT.aux.mix
 	vtol_TTTTAAER.aux.mix
@@ -0,0 +1,66 @@
+Viper Delta-wing mixer
+=================================
+# @board px4_fmu-v2 exclude
+
+Designed for Viper.
+
+TODO (sjwilks): Add mixers for flaps.
+
+This file defines mixers suitable for controlling a delta wing aircraft using
+PX4FMU. The configuration assumes the elevon servos are connected to PX4FMU
+servo outputs 0 and 1 and the motor speed control to output 3. Output 2 is
+assumed to be unused.
+
+Inputs to the mixer come from channel group 0 (vehicle attitude), channels 0
+(roll), 1 (pitch) and 3 (thrust).
+
+See the README for more information on the scaler format.
+
+Elevon mixers
+-------------
+Three scalers total (output, roll, pitch).
+
+On the assumption that the two elevon servos are physically reversed, the pitch
+input is inverted between the two servos.
+
+The scaling factor for roll inputs is adjusted to implement differential travel
+for the elevons.
+
+M: 2
+S: 0 0   7500   7500      0 -10000  10000
+S: 0 1   8000   8000      0 -10000  10000
+
+M: 2
+S: 0 0   7500   7500      0 -10000  10000
+S: 0 1  -8000  -8000      0 -10000  10000
+
+Output 2
+--------
+This mixer is empty.
+
+Z:
+
+Motor speed mixer
+-----------------
+Two scalers total (output, thrust).
+
+This mixer generates a full-range output (-1 to 1) from an input in the (0 - 1)
+range.  Inputs below zero are treated as zero.
+
+M: 1
+S: 0 3      0  20000 -10000 -10000  10000
+
+Inputs to the mixer come from channel group 2 (payload), channels 0
+(bay servo 1), 1 (bay servo 2) and 3 (drop release).
+-----------------------------------------------------
+
+M: 1
+S: 2 0  10000  10000      0 -10000  10000
+
+M: 1
+S: 2 1  10000  10000      0 -10000  10000
+
+M: 1
+S: 2 2  -8000  -8000      0 -10000  10000
+
+
@@ -0,0 +1,28 @@
+# mixer for the CruiseAder Claire tilt mechansim servo and elevons
+
+=======================================================================
+
+
+Tilt mechanism servo mixer
+
+---------------------------
+
+M: 1
+
+
+S: 1 8  10000  10000      0 -10000  10000
+
+
+
+Elevon mixers
+
+-------------
+
+M: 2
+
+S: 1 0   7500   7500      0 -10000  10000
+S: 1 1   7500   7500      0 -10000  10000
+
+M: 2
+S: 1 0    7500    7500    0 -10000  10000
+S: 1 1   -7500   -7500    0 -10000  10000
@@ -0,0 +1,8 @@
+# CruiseAder Claire Main Multirotor mixer for PX4FMU
+# @board px4_fmu-v2 exclude
+
+#
+
+#===========================
+
+R: 4x
@@ -5,7 +5,7 @@ Tailsitter duo mixer
 This file defines a mixer for a generic duo tailsitter VTOL (eg TBS Caipirinha tailsitter edition). This vehicle
 has two motors in total, one attached to each wing. It also has two elevons which
 are located in the slipstream of the propellers. This mixer generates 4 PWM outputs
-on the main PWM output port, two at 400Hz for the motors, and two at 50Hz for the
+on the main PWM ouput port, two at 400Hz for the motors, and two at 50Hz for the
 elevon servos. Channels 1-4 are configured to run at 400Hz, while channels 5-8 run
 at the default rate of 50Hz. Note that channels 3 and 4 are assigned but not used.

@@ -4,7 +4,7 @@ Tailsitter duo mixer
 This file defines a mixer for a generic duo tailsitter VTOL (eg TBS Caipirinha tailsitter edition). This vehicle
 has two motors in total, one attached to each wing. It also has two elevons which
 are located in the slipstream of the propellers. This mixer generates 4 PWM outputs
-on the main PWM output port, two at 400Hz for the motors, and two at 50Hz for the
+on the main PWM ouput port, two at 400Hz for the motors, and two at 50Hz for the
 elevon servos. Channels 1-4 are configured to run at 400Hz, while channels 5-8 run
 at the default rate of 50Hz. Note that channels 3 and 4 are assigned but not used.

@@ -95,7 +95,7 @@ def do_nsh_cmd(port_url, baudrate, cmd):


    timeout_start = time.monotonic()
-    timeout = 600 # 10 minutes
+    timeout = 240 # 4 minutes

    return_code = 0

@@ -13,11 +13,11 @@ exec find boards msg src platforms test \
    -path platforms/qurt/dspal -prune -o \
    -path src/drivers/uavcan/libuavcan -prune -o \
    -path src/drivers/uavcan/uavcan_drivers/kinetis/driver/include/uavcan_kinetis -prune -o \
-    -path src/drivers/cyphal/libcanard -prune -o \
+    -path src/drivers/uavcan_v1/libcanard -prune -o \
+    -path src/drivers/uavcannode_gps_demo/libcanard -prune -o \
    -path src/lib/crypto/monocypher -prune -o \
    -path src/lib/events/libevents -prune -o \
    -path src/lib/parameters/uthash -prune -o \
-    -path src/lib/wind_estimator/python/generated -prune -o \
    -path src/modules/ekf2/EKF -prune -o \
    -path src/modules/gyro_fft/CMSIS_5 -prune -o \
    -path src/modules/mavlink/mavlink -prune -o \
@@ -11,7 +11,7 @@ from pyulog import ULog
 from analysis.detectors import InAirDetector, PreconditionError
 from analysis.metrics import calculate_ecl_ekf_metrics
 from analysis.checks import perform_ecl_ekf_checks
-from analysis.post_processing import get_gps_check_fail_flags
+from analysis.post_processing import get_estimator_check_flags

 def analyse_ekf(
        ulog: ULog, check_levels: Dict[str, float], multi_instance: int = 0,
@@ -40,11 +40,6 @@ def analyse_ekf(
    except:
        raise PreconditionError('could not find estimator_status instance', multi_instance)

-    try:
-        estimator_status_flags = ulog.get_dataset('estimator_status_flags', multi_instance).data
-    except:
-        raise PreconditionError('could not find estimator_status_flags instance', multi_instance)
-
    try:
        _ = ulog.get_dataset('estimator_innovations', multi_instance).data
    except:
@@ -66,14 +61,14 @@ def analyse_ekf(
        'in_air_transition_time': round(in_air.take_off + in_air.log_start, 2),
        'on_ground_transition_time': round(in_air.landing + in_air.log_start, 2)}

-    gps_fail_flags = get_gps_check_fail_flags(estimator_status)
+    control_mode, innov_flags, gps_fail_flags = get_estimator_check_flags(estimator_status)

    sensor_checks, innov_fail_checks = find_checks_that_apply(
-        estimator_status_flags, estimator_status,
+        control_mode, estimator_status,
        pos_checks_when_sensors_not_fused=pos_checks_when_sensors_not_fused)

    metrics = calculate_ecl_ekf_metrics(
-        ulog, estimator_status_flags, innov_fail_checks, sensor_checks, in_air, in_air_no_ground_effects,
+        ulog, innov_flags, innov_fail_checks, sensor_checks, in_air, in_air_no_ground_effects,
        multi_instance, red_thresh=red_thresh, amb_thresh=amb_thresh)

    check_status, master_status = perform_ecl_ekf_checks(
@@ -83,12 +78,12 @@ def analyse_ekf(


 def find_checks_that_apply(
-    estimator_status_flags: dict, estimator_status: dict, pos_checks_when_sensors_not_fused: bool = False) ->\
+    control_mode: dict, estimator_status: dict, pos_checks_when_sensors_not_fused: bool = False) ->\
        Tuple[List[str], List[str]]:
    """
    finds the checks that apply and stores them in lists for the std checks and the innovation
    fail checks.
-    :param estimator_status_flags:
+    :param control_mode:
    :param estimator_status:
    :param b_pos_only_when_sensors_fused:
    :return: a tuple of two lists that contain strings for the std checks and for the innovation
@@ -102,7 +97,7 @@ def find_checks_that_apply(
    innov_fail_checks.append('posv')

    # Magnetometer Sensor Checks
-    if (np.amax(estimator_status_flags['cs_yaw_align']) > 0.5):
+    if (np.amax(control_mode['yaw_aligned']) > 0.5):
        sensor_checks.append('mag')

        innov_fail_checks.append('magx')
@@ -111,14 +106,13 @@ def find_checks_that_apply(
        innov_fail_checks.append('yaw')

    # Velocity Sensor Checks
-    if (np.amax(estimator_status_flags['cs_gps']) > 0.5):
+    if (np.amax(control_mode['using_gps']) > 0.5):
        sensor_checks.append('vel')
-        innov_fail_checks.append('velh')
-        innov_fail_checks.append('velv')
+        innov_fail_checks.append('vel')

    # Position Sensor Checks
-    if (pos_checks_when_sensors_not_fused or (np.amax(estimator_status_flags['cs_gps']) > 0.5)
-        or (np.amax(estimator_status_flags['cs_ev_pos']) > 0.5)):
+    if (pos_checks_when_sensors_not_fused or (np.amax(control_mode['using_gps']) > 0.5)
+        or (np.amax(control_mode['using_evpos']) > 0.5)):
        sensor_checks.append('pos')
        innov_fail_checks.append('posh')

@@ -134,7 +128,7 @@ def find_checks_that_apply(
        innov_fail_checks.append('hagl')

    # optical flow sensor checks
-    if (np.amax(estimator_status_flags['cs_opt_flow']) > 0.5):
+    if (np.amax(control_mode['using_optflow']) > 0.5):
        innov_fail_checks.append('ofx')
        innov_fail_checks.append('ofy')

@@ -123,8 +123,7 @@ def perform_sensor_innov_checks(
                                              ('magy', 'magy_fail_percentage', 'mag'),
                                              ('magz', 'magz_fail_percentage', 'mag'),
                                              ('yaw', 'yaw_fail_percentage', 'yaw'),
-                                              ('velh', 'vel_fail_percentage', 'vel'),
-                                              ('velv', 'vel_fail_percentage', 'vel'),
+                                              ('vel', 'vel_fail_percentage', 'vel'),
                                              ('posh', 'pos_fail_percentage', 'pos'),
                                              ('tas', 'tas_fail_percentage', 'tas'),
                                              ('hagl', 'hagl_fail_percentage', 'hagl'),
@@ -11,7 +11,7 @@ import numpy as np
 from analysis.detectors import InAirDetector

 def calculate_ecl_ekf_metrics(
-        ulog: ULog, estimator_status_flags: Dict[str, float], innov_fail_checks: List[str],
+        ulog: ULog, innov_flags: Dict[str, float], innov_fail_checks: List[str],
        sensor_checks: List[str], in_air: InAirDetector, in_air_no_ground_effects: InAirDetector,
        multi_instance: int = 0, red_thresh: float = 1.0, amb_thresh: float = 0.5) -> Tuple[dict, dict, dict, dict]:

@@ -20,7 +20,7 @@ def calculate_ecl_ekf_metrics(
        red_thresh=red_thresh, amb_thresh=amb_thresh)

    innov_fail_metrics = calculate_innov_fail_metrics(
-        estimator_status_flags, innov_fail_checks, in_air, in_air_no_ground_effects)
+        innov_flags, innov_fail_checks, in_air, in_air_no_ground_effects)

    imu_metrics = calculate_imu_metrics(ulog, multi_instance, in_air_no_ground_effects)

@@ -90,10 +90,10 @@ def calculate_sensor_metrics(


 def calculate_innov_fail_metrics(
-        estimator_status_flags: dict, innov_fail_checks: List[str], in_air: InAirDetector,
+        innov_flags: dict, innov_fail_checks: List[str], in_air: InAirDetector,
        in_air_no_ground_effects: InAirDetector) -> dict:
    """
-    :param estimator_status_flags:
+    :param innov_flags:
    :param innov_fail_checks:
    :param in_air:
    :param in_air_no_ground_effects:
@@ -103,18 +103,17 @@ def calculate_innov_fail_metrics(
    innov_fail_metrics = dict()

    # calculate innovation check fail metrics
-    for signal_id, signal, result in [('posv', 'reject_ver_pos', 'hgt_fail_percentage'),
-                                      ('magx', 'reject_mag_x', 'magx_fail_percentage'),
-                                      ('magy', 'reject_mag_y', 'magy_fail_percentage'),
-                                      ('magz', 'reject_mag_z', 'magz_fail_percentage'),
-                                      ('yaw', 'reject_yaw', 'yaw_fail_percentage'),
-                                      ('velh', 'reject_hor_vel', 'vel_fail_percentage'),
-                                      ('velv', 'reject_ver_vel', 'vel_fail_percentage'),
-                                      ('posh', 'reject_hor_pos', 'pos_fail_percentage'),
-                                      ('tas', 'reject_airspeed', 'tas_fail_percentage'),
-                                      ('hagl', 'reject_hagl', 'hagl_fail_percentage'),
-                                      ('ofx', 'reject_optflow_x', 'ofx_fail_percentage'),
-                                      ('ofy', 'reject_optflow_y', 'ofy_fail_percentage')]:
+    for signal_id, signal, result in [('posv', 'posv_innov_fail', 'hgt_fail_percentage'),
+                                      ('magx', 'magx_innov_fail', 'magx_fail_percentage'),
+                                      ('magy', 'magy_innov_fail', 'magy_fail_percentage'),
+                                      ('magz', 'magz_innov_fail', 'magz_fail_percentage'),
+                                      ('yaw', 'yaw_innov_fail', 'yaw_fail_percentage'),
+                                      ('vel', 'vel_innov_fail', 'vel_fail_percentage'),
+                                      ('posh', 'posh_innov_fail', 'pos_fail_percentage'),
+                                      ('tas', 'tas_innov_fail', 'tas_fail_percentage'),
+                                      ('hagl', 'hagl_innov_fail', 'hagl_fail_percentage'),
+                                      ('ofx', 'ofx_innov_fail', 'ofx_fail_percentage'),
+                                      ('ofy', 'ofy_innov_fail', 'ofy_fail_percentage')]:

        # only run innov fail checks, if they apply.
        if signal_id in innov_fail_checks:
@@ -126,7 +125,7 @@ def calculate_innov_fail_metrics(
                in_air_detector = in_air

            innov_fail_metrics[result] = calculate_stat_from_signal(
-                estimator_status_flags, 'estimator_status_flags', signal, in_air_detector,
+                innov_flags, 'estimator_status', signal, in_air_detector,
                lambda x: 100.0 * np.mean(x > 0.5))

    return innov_fail_metrics
@@ -153,7 +152,7 @@ def calculate_imu_metrics(ulog: ULog, multi_instance, in_air_no_ground_effects:

            if vehicle_imu_status_data['accel_device_id'][0] == estimator_status_data['accel_device_id'][0]:

-                for signal, result in [('gyro_coning_vibration', 'imu_coning'),
+                for signal, result in [('delta_angle_coning_metric', 'imu_coning'),
                                       ('gyro_vibration_metric', 'imu_hfgyro'),
                                       ('accel_vibration_metric', 'imu_hfaccel')]:

@@ -7,6 +7,115 @@ from typing import Tuple

 import numpy as np

+
+def get_estimator_check_flags(estimator_status: dict) -> Tuple[dict, dict, dict]:
+    """
+    :param estimator_status:
+    :return:
+    """
+    control_mode = get_control_mode_flags(estimator_status)
+    innov_flags = get_innovation_check_flags(estimator_status)
+    gps_fail_flags = get_gps_check_fail_flags(estimator_status)
+    return control_mode, innov_flags, gps_fail_flags
+
+
+def get_control_mode_flags(estimator_status: dict) -> dict:
+    """
+    :param estimator_status:
+    :return:
+    """
+
+    control_mode = dict()
+    # extract control mode metadata from estimator_status.control_mode_flags
+    # 0 - true if the filter tilt alignment is complete
+    # 1 - true if the filter yaw alignment is complete
+    # 2 - true if GPS measurements are being fused
+    # 3 - true if optical flow measurements are being fused
+    # 4 - true if a simple magnetic yaw heading is being fused
+    # 5 - true if 3-axis magnetometer measurement are being fused
+    # 6 - true if synthetic magnetic declination measurements are being fused
+    # 7 - true when the vehicle is airborne
+    # 8 - true when wind velocity is being estimated
+    # 9 - true when baro height is being fused as a primary height reference
+    # 10 - true when range finder height is being fused as a primary height reference
+    # 11 - true when range finder height is being fused as a primary height reference
+    # 12 - true when local position data from external vision is being fused
+    # 13 - true when yaw data from external vision measurements is being fused
+    # 14 - true when height data from external vision measurements is being fused
+    # 15 - true when synthetic sideslip measurements are being fused
+    # 16 - true true when the mag field does not match the expected strength
+    # 17 - true true when the vehicle is operating as a fixed wing vehicle
+    # 18 - true when the magnetometer has been declared faulty and is no longer being used
+    # 19 - true true when airspeed measurements are being fused
+    # 20 - true true when protection from ground effect induced static pressure rise is active
+    # 21 - true when rng data wasn't ready for more than 10s and new rng values haven't changed enough
+    # 22 - true when yaw (not ground course) data from a GPS receiver is being fused
+    # 23 - true when the in-flight mag field alignment has been completed
+    # 24 - true when local earth frame velocity data from external vision measurements are being fused
+    # 25 - true when we are using a synthesized measurement for the magnetometer Z component
+    control_mode['tilt_aligned'] = ((2 ** 0 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['yaw_aligned'] = ((2 ** 1 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['using_gps'] = ((2 ** 2 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['using_optflow'] = ((2 ** 3 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['using_magyaw'] = ((2 ** 4 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['using_mag3d'] = ((2 ** 5 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['using_magdecl'] = ((2 ** 6 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['airborne'] = ((2 ** 7 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['estimating_wind'] = ((2 ** 8 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['using_barohgt'] = ((2 ** 9 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['using_rnghgt'] = ((2 ** 10 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['using_gpshgt'] = ((2 ** 11 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['using_evpos'] = ((2 ** 12 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['using_evyaw'] = ((2 ** 13 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['using_evhgt'] = ((2 ** 14 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['fuse_beta'] = ((2 ** 15 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['mag_field_disturbed'] = ((2 ** 16 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['fixed_wing'] = ((2 ** 17 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['mag_fault'] = ((2 ** 18 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['fuse_aspd'] = ((2 ** 19 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['gnd_effect'] = ((2 ** 20 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['rng_stuck'] = ((2 ** 21 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['gps_yaw'] = ((2 ** 22 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['mag_aligned_in_flight'] = ((2 ** 23 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['ev_vel'] = ((2 ** 24 & estimator_status['control_mode_flags']) > 0) * 1
+    control_mode['synthetic_mag_z'] = ((2 ** 25 & estimator_status['control_mode_flags']) > 0) * 1
+    return control_mode
+
+def get_innovation_check_flags(estimator_status: dict) -> dict:
+    """
+    :param estimator_status:
+    :return:
+    """
+
+    innov_flags = dict()
+    # innovation_check_flags summary
+    # 0 - true if velocity observations have been rejected
+    # 1 - true if horizontal position observations have been rejected
+    # 2 - true if true if vertical position observations have been rejected
+    # 3 - true if the X magnetometer observation has been rejected
+    # 4 - true if the Y magnetometer observation has been rejected
+    # 5 - true if the Z magnetometer observation has been rejected
+    # 6 - true if the yaw observation has been rejected
+    # 7 - true if the airspeed observation has been rejected
+    # 8 - true if synthetic sideslip observation has been rejected
+    # 9 - true if the height above ground observation has been rejected
+    # 10 - true if the X optical flow observation has been rejected
+    # 11 - true if the Y optical flow observation has been rejected
+    innov_flags['vel_innov_fail'] = ((2 ** 0 & estimator_status['innovation_check_flags']) > 0) * 1
+    innov_flags['posh_innov_fail'] = ((2 ** 1 & estimator_status['innovation_check_flags']) > 0) * 1
+    innov_flags['posv_innov_fail'] = ((2 ** 2 & estimator_status['innovation_check_flags']) > 0) * 1
+    innov_flags['magx_innov_fail'] = ((2 ** 3 & estimator_status['innovation_check_flags']) > 0) * 1
+    innov_flags['magy_innov_fail'] = ((2 ** 4 & estimator_status['innovation_check_flags']) > 0) * 1
+    innov_flags['magz_innov_fail'] = ((2 ** 5 & estimator_status['innovation_check_flags']) > 0) * 1
+    innov_flags['yaw_innov_fail'] = ((2 ** 6 & estimator_status['innovation_check_flags']) > 0) * 1
+    innov_flags['tas_innov_fail'] = ((2 ** 7 & estimator_status['innovation_check_flags']) > 0) * 1
+    innov_flags['sli_innov_fail'] = ((2 ** 8 & estimator_status['innovation_check_flags']) > 0) * 1
+    innov_flags['hagl_innov_fail'] = ((2 ** 9 & estimator_status['innovation_check_flags']) > 0) * 1
+    innov_flags['ofx_innov_fail'] = ((2 ** 10 & estimator_status['innovation_check_flags']) > 0) * 1
+    innov_flags['ofy_innov_fail'] = ((2 ** 11 & estimator_status['innovation_check_flags']) > 0) * 1
+    return innov_flags
+
+
 def get_gps_check_fail_flags(estimator_status: dict) -> dict:
    """
    :param estimator_status:
@@ -11,7 +11,7 @@ import numpy as np
 from matplotlib.backends.backend_pdf import PdfPages
 from pyulog import ULog

-from analysis.post_processing import magnetic_field_estimates_from_states, get_gps_check_fail_flags
+from analysis.post_processing import magnetic_field_estimates_from_states, get_estimator_check_flags
 from plotting.data_plots import TimeSeriesPlot, InnovationPlot, ControlModeSummaryPlot, \
    CheckFlagsPlot
 from analysis.detectors import PreconditionError
@@ -33,11 +33,6 @@ def create_pdf_report(ulog: ULog, multi_instance: int, output_plot_filename: str
    except:
        raise PreconditionError('could not find estimator_status instance', multi_instance)

-    try:
-        estimator_status_flags = ulog.get_dataset('estimator_status_flags', multi_instance).data
-    except:
-        raise PreconditionError('could not find estimator_status_flags instance', multi_instance)
-
    try:
        estimator_states = ulog.get_dataset('estimator_states', multi_instance).data
    except:
@@ -73,13 +68,12 @@ def create_pdf_report(ulog: ULog, multi_instance: int, output_plot_filename: str
    except:
        raise PreconditionError('could not find innovation data')

-    gps_fail_flags = get_gps_check_fail_flags(estimator_status)
+    control_mode, innov_flags, gps_fail_flags = get_estimator_check_flags(estimator_status)

    status_time = 1e-6 * estimator_status['timestamp']
-    status_flags_time = 1e-6 * estimator_status_flags['timestamp']

    b_finishes_in_air, b_starts_in_air, in_air_duration, in_air_transition_time, \
-    on_ground_transition_time = detect_airtime(estimator_status_flags, status_flags_time)
+    on_ground_transition_time = detect_airtime(control_mode, status_time)

    with PdfPages(output_plot_filename) as pdf_pages:

@@ -179,9 +173,9 @@ def create_pdf_report(ulog: ULog, multi_instance: int, output_plot_filename: str

        # plot control mode summary A
        data_plot = ControlModeSummaryPlot(
-            status_flags_time, estimator_status_flags, [['cs_tilt_align', 'cs_yaw_align'],
-            ['cs_gps', 'cs_opt_flow', 'cs_ev_pos'], ['cs_baro_hgt', 'cs_gps_hgt',
-             'cs_rng_hgt', 'cs_ev_hgt'], ['cs_mag_hdg', 'cs_mag_3d', 'cs_mag_dec']],
+            status_time, control_mode, [['tilt_aligned', 'yaw_aligned'],
+            ['using_gps', 'using_optflow', 'using_evpos'], ['using_barohgt', 'using_gpshgt',
+             'using_rnghgt', 'using_evhgt'], ['using_magyaw', 'using_mag3d', 'using_magdecl']],
            x_label='time (sec)', y_labels=['aligned', 'pos aiding', 'hgt aiding', 'mag aiding'],
            annotation_text=[['tilt alignment', 'yaw alignment'], ['GPS aiding', 'optical flow aiding',
             'external vision aiding'], ['Baro aiding', 'GPS aiding', 'rangefinder aiding',
@@ -194,7 +188,7 @@ def create_pdf_report(ulog: ULog, multi_instance: int, output_plot_filename: str
        # plot control mode summary B
        # construct additional annotations for the airborne plot
        airborne_annotations = list()
-        if np.amin(np.diff(estimator_status_flags['cs_in_air'])) > -0.5:
+        if np.amin(np.diff(control_mode['airborne'])) > -0.5:
            airborne_annotations.append(
                (on_ground_transition_time, 'air to ground transition not detected'))
        else:
@@ -203,7 +197,7 @@ def create_pdf_report(ulog: ULog, multi_instance: int, output_plot_filename: str
        if in_air_duration > 0.0:
            airborne_annotations.append(((in_air_transition_time + on_ground_transition_time) / 2,
                                         'duration = {:.1f} sec'.format(in_air_duration)))
-        if np.amax(np.diff(estimator_status_flags['cs_in_air'])) < 0.5:
+        if np.amax(np.diff(control_mode['airborne'])) < 0.5:
            airborne_annotations.append(
                (in_air_transition_time, 'ground to air transition not detected'))
        else:
@@ -211,7 +205,7 @@ def create_pdf_report(ulog: ULog, multi_instance: int, output_plot_filename: str
                (in_air_transition_time, 'in-air at {:.1f} sec'.format(in_air_transition_time)))

        data_plot = ControlModeSummaryPlot(
-            status_flags_time, estimator_status_flags, [['cs_in_air'], ['cs_wind']],
+            status_time, control_mode, [['airborne'], ['estimating_wind']],
            x_label='time (sec)', y_labels=['airborne', 'estimating wind'], annotation_text=[[], []],
            additional_annotation=[airborne_annotations, []],
            plot_title='EKF Control Status - Figure B', pdf_handle=pdf_pages)
@@ -220,15 +214,15 @@ def create_pdf_report(ulog: ULog, multi_instance: int, output_plot_filename: str

        # plot innovation_check_flags summary
        data_plot = CheckFlagsPlot(
-            status_flags_time, estimator_status_flags, [['reject_hor_vel', 'reject_hor_pos'], ['reject_ver_vel', 'reject_ver_pos',
-                                                                               'reject_hagl'],
-                                       ['reject_mag_x', 'reject_mag_y', 'reject_mag_z',
-                                        'reject_yaw'], ['reject_airspeed'], ['reject_sideslip'],
-                                       ['reject_optflow_x',
-                                        'reject_optflow_y']], x_label='time (sec)',
+            status_time, innov_flags, [['vel_innov_fail', 'posh_innov_fail'], ['posv_innov_fail',
+                                                                               'hagl_innov_fail'],
+                                       ['magx_innov_fail', 'magy_innov_fail', 'magz_innov_fail',
+                                        'yaw_innov_fail'], ['tas_innov_fail'], ['sli_innov_fail'],
+                                       ['ofx_innov_fail',
+                                        'ofy_innov_fail']], x_label='time (sec)',
            y_labels=['failed', 'failed', 'failed', 'failed', 'failed', 'failed'],
            y_lim=(-0.1, 1.1),
-            legend=[['vel NE', 'pos NE'], ['vel D', 'hgt absolute', 'hgt above ground'],
+            legend=[['vel NED', 'pos NE'], ['hgt absolute', 'hgt above ground'],
                    ['mag_x', 'mag_y', 'mag_z', 'yaw'], ['airspeed'], ['sideslip'],
                    ['flow X', 'flow Y']],
            plot_title='EKF Innovation Test Fails', annotate=False, pdf_handle=pdf_pages)
@@ -350,33 +344,33 @@ def create_pdf_report(ulog: ULog, multi_instance: int, output_plot_filename: str
        data_plot.close()


-def detect_airtime(estimator_status_flags, status_flags_time):
+def detect_airtime(control_mode, status_time):
    # define flags for starting and finishing in air
    b_starts_in_air = False
    b_finishes_in_air = False
    # calculate in-air transition time
-    if (np.amin(estimator_status_flags['cs_in_air']) < 0.5) and (np.amax(estimator_status_flags['cs_in_air']) > 0.5):
-        in_air_transtion_time_arg = np.argmax(np.diff(estimator_status_flags['cs_in_air']))
-        in_air_transition_time = status_flags_time[in_air_transtion_time_arg]
-    elif (np.amax(estimator_status_flags['cs_in_air']) > 0.5):
-        in_air_transition_time = np.amin(status_flags_time)
+    if (np.amin(control_mode['airborne']) < 0.5) and (np.amax(control_mode['airborne']) > 0.5):
+        in_air_transtion_time_arg = np.argmax(np.diff(control_mode['airborne']))
+        in_air_transition_time = status_time[in_air_transtion_time_arg]
+    elif (np.amax(control_mode['airborne']) > 0.5):
+        in_air_transition_time = np.amin(status_time)
        print('log starts while in-air at ' + str(round(in_air_transition_time, 1)) + ' sec')
        b_starts_in_air = True
    else:
        in_air_transition_time = float('NaN')
        print('always on ground')
    # calculate on-ground transition time
-    if (np.amin(np.diff(estimator_status_flags['cs_in_air'])) < 0.0):
-        on_ground_transition_time_arg = np.argmin(np.diff(estimator_status_flags['cs_in_air']))
-        on_ground_transition_time = status_flags_time[on_ground_transition_time_arg]
-    elif (np.amax(estimator_status_flags['cs_in_air']) > 0.5):
-        on_ground_transition_time = np.amax(status_flags_time)
+    if (np.amin(np.diff(control_mode['airborne'])) < 0.0):
+        on_ground_transition_time_arg = np.argmin(np.diff(control_mode['airborne']))
+        on_ground_transition_time = status_time[on_ground_transition_time_arg]
+    elif (np.amax(control_mode['airborne']) > 0.5):
+        on_ground_transition_time = np.amax(status_time)
        print('log finishes while in-air at ' + str(round(on_ground_transition_time, 1)) + ' sec')
        b_finishes_in_air = True
    else:
        on_ground_transition_time = float('NaN')
        print('always on ground')
-    if (np.amax(np.diff(estimator_status_flags['cs_in_air'])) > 0.5) and (np.amin(np.diff(estimator_status_flags['cs_in_air'])) < -0.5):
+    if (np.amax(np.diff(control_mode['airborne'])) > 0.5) and (np.amin(np.diff(control_mode['airborne'])) < -0.5):
        if ((on_ground_transition_time - in_air_transition_time) > 0.0):
            in_air_duration = on_ground_transition_time - in_air_transition_time
        else:
@@ -5,13 +5,12 @@ set -e
 SCRIPT_DIR="$( cd "$( dirname "${BASH_SOURCE[0]}" )" && pwd )"
 cd "$SCRIPT_DIR/jMAVSim"

-port=4560
+tcp_port=4560
 extra_args=
 baudrate=921600
 device=
 ip="127.0.0.1"
-protocol="tcp"
-while getopts ":b:d:u:p:qsr:f:i:loat" opt; do
+while getopts ":b:d:p:qsr:f:i:loat" opt; do
 	case $opt in
 		b)
 			baudrate=$OPTARG
@@ -19,14 +18,11 @@ while getopts ":b:d:u:p:qsr:f:i:loat" opt; do
 		d)
 			device="$OPTARG"
 			;;
-		u)
-			protocol="udp"
-			;;
 		i)
 			ip="$OPTARG"
 			;;
 		p)
-			port=$OPTARG
+			tcp_port=$OPTARG
 			;;
 		q)
 			extra_args="$extra_args -qgc"
@@ -57,11 +53,7 @@ while getopts ":b:d:u:p:qsr:f:i:loat" opt; do
 done

 if [ "$device" == "" ]; then
-	if [ "$protocol" == "tcp" ]; then
-		device="-tcp $ip:$port"
-	else
-		device="-udp $port"
-	fi
+	device="-tcp $ip:$tcp_port"
 else
 	device="-serial $device $baudrate"
 fi
@@ -0,0 +1,72 @@
+#!/bin/python3
+
+import parse_cmake.parsing as cmp
+import glob
+import pprint
+import re
+import os
+
+__location__ = os.path.realpath(
+    os.path.join(os.getcwd(), os.path.dirname(__file__)))
+
+serial_regex = r"(\D\D\D\d):(/dev/ttyS\d+)"
+io_regex = r"IO (.*)"
+romfs_regex = r"ROMFSROOT (.*)"
+arch_regex = r"ARCHITECTURE (.*)"
+toolchain_regex = r"TOOLCHAIN (.*)"
+
+
+
+def stripComments(code):
+    code = str(code)
+    return re.sub(r'(?m) *#.*\n?', '', code)
+
+lut = {}
+with open(os.path.join(__location__, "cmake_kconfig_lut.txt"),'r') as lookup:
+    for line in lookup:
+        if ',' in line:
+            key, value = line.strip().split(',')
+            lut[key] = value
+
+#for name in glob.glob('boards/*/*/*.cmake'):
+px4_dir = os.path.abspath(os.path.join(os.path.dirname(__file__), '../../'))
+
+for name in glob.glob(px4_dir + '/boards/*/*/*.cmake'):
+    print(name)
+    with open(name, 'r') as f:
+        romfs_set = False
+        w = open(name.replace(".cmake",".px4board"), "w")
+        for line in f:
+            clean_line = stripComments(line.strip())
+            value = lut.get(clean_line)
+            if value is not None:
+                print(value, file=w)
+                print(value)
+            else:
+                matches = re.finditer(serial_regex, clean_line, re.MULTILINE)
+                for matchNum, match in enumerate(matches, start=1):
+                    print("CONFIG_BOARD_SERIAL_" + match.groups()[0] + "=\"" + match.groups()[1] + "\"")
+                    print("CONFIG_BOARD_SERIAL_" + match.groups()[0] + "=\"" + match.groups()[1] + "\"", file=w)
+                matches = re.finditer(io_regex, clean_line, re.MULTILINE)
+                for matchNum, match in enumerate(matches, start=1):
+                    print("CONFIG_BOARD_IO=\"" + match.groups()[0] + "\"")
+                    print("CONFIG_BOARD_IO=\"" + match.groups()[0] + "\"", file=w)
+                matches = re.finditer(romfs_regex, clean_line, re.MULTILINE)
+                for matchNum, match in enumerate(matches, start=1):
+                    print("CONFIG_BOARD_ROMFSROOT=\"" + match.groups()[0] + "\"")
+                    print("CONFIG_BOARD_ROMFSROOT=\"" + match.groups()[0] + "\"", file=w)
+                    romfs_set = True
+                matches = re.finditer(arch_regex, clean_line, re.MULTILINE)
+                for matchNum, match in enumerate(matches, start=1):
+                    print("CONFIG_BOARD_ARCHITECTURE=\"" + match.groups()[0] + "\"")
+                    print("CONFIG_BOARD_ARCHITECTURE=\"" + match.groups()[0] + "\"", file=w)
+                matches = re.finditer(toolchain_regex, clean_line, re.MULTILINE)
+                for matchNum, match in enumerate(matches, start=1):
+                    print("CONFIG_BOARD_TOOLCHAIN=\"" + match.groups()[0] + "\"")
+                    print("CONFIG_BOARD_TOOLCHAIN=\"" + match.groups()[0] + "\"", file=w)
+
+    if(romfs_set == False):
+        print("CONFIG_BOARD_ROMFSROOT=\"\"", file=w)
+
+
+    w.close()
@@ -0,0 +1,204 @@
+PLATFORM nuttx,CONFIG_PLATFORM_NUTTX=y
+PLATFORM posix,CONFIG_PLATFORM_POSIX=y
+CONSTRAINED_MEMORY,CONFIG_BOARD_CONSTRAINED_MEMORY=y
+CONSTRAINED_FLASH,CONFIG_BOARD_CONSTRAINED_FLASH=y
+NO_HELP,CONFIG_BOARD_NO_HELP=y
+EXTERNAL_METADATA,CONFIG_BOARD_EXTERNAL_METADATA=y
+BUILD_BOOTLOADER,CONFIG_BOARD_BUILD_BOOTLOADER=y
+UAVCAN_INTERFACES 2,CONFIG_BOARD_UAVCAN_INTERFACES=2
+UAVCAN_INTERFACES 1,CONFIG_BOARD_UAVCAN_INTERFACES=1
+UAVCAN_TIMER_OVERRIDE 2,CONFIG_BOARD_UAVCAN_TIMER_OVERRIDE=2
+UAVCAN_TIMER_OVERRIDE 1,CONFIG_BOARD_UAVCAN_TIMER_OVERRIDE=1
+UAVCAN_TIMER_OVERRIDE 1,CONFIG_BOARD_UAVCAN_TIMER_OVERRIDE=0
+TESTING,CONFIG_BOARD_TESTING=y
+ETHERNET,CONFIG_BOARD_ETHERNET=y
+adc/ads1115,CONFIG_DRIVERS_ADC_ADS1115=y
+adc/board_adc,CONFIG_DRIVERS_ADC_BOARD_ADC=y
+barometer,CONFIG_COMMON_BAROMETERS=y
+barometer/bmp280,CONFIG_DRIVERS_BAROMETER_BMP280=y
+barometer/bmp388,CONFIG_DRIVERS_BAROMETER_BMP388=y
+barometer/dps310,CONFIG_DRIVERS_BAROMETER_DPS310=y
+barometer/lps22hb,CONFIG_DRIVERS_BAROMETER_LPS22HB=y
+barometer/lps25h,CONFIG_DRIVERS_BAROMETER_LPS25H=y
+barometer/lps33hw,CONFIG_DRIVERS_BAROMETER_LPS33HW=y
+barometer/mpl3115a2,CONFIG_DRIVERS_BAROMETER_MPL3115A2=y
+barometer/ms5611,CONFIG_DRIVERS_BAROMETER_MS5611=y
+barometer/tcbp001ta,CONFIG_DRIVERS_BAROMETER_TCBP001TA=y
+batt_smbus,CONFIG_DRIVERS_BATT_SMBUS=y
+bootloaders,CONFIG_DRIVERS_BOOTLOADERS=y
+camera_capture,CONFIG_DRIVERS_CAMERA_CAPTURE=y
+camera_trigger,CONFIG_DRIVERS_CAMERA_TRIGGER=y
+differential_pressure,CONFIG_DRIVERS_DIFFERENTIAL_PRESSURE=y
+distance_sensor,CONFIG_COMMON_DISTANCE_SENSOR=y
+distance_sensor/ll40ls,CONFIG_DRIVERS_DISTANCE_SENSOR_LL40LS=y
+distance_sensor/lightware_laser_serial,CONFIG_DRIVERS_DISTANCE_SENSOR_LIGHTWARE_LASER_SERIAL=y
+distance_sensor/broadcom/afbrs50,CONFIG_DRIVERS_DISTANCE_SENSOR_BROADCOM_AFBRS50=y
+distance_sensor/vl53l0x,CONFIG_DRIVERS_DISTANCE_SENSOR_VL53L0X=y
+distance_sensor/vl53l1x,CONFIG_DRIVERS_DISTANCE_SENSOR_VL53L1X=y
+distance_sensor/srf05,CONFIG_DRIVERS_DISTANCE_SENSOR_SRF05=y
+dshot,CONFIG_DRIVERS_DSHOT=y
+gps,CONFIG_DRIVERS_GPS=y
+heater,CONFIG_DRIVERS_HEATER=y
+imu,CONFIG_COMMON_IMU=y
+imu/adis16477,CONFIG_DRIVERS_IMU_ADIS16477=y
+imu/adis16497,CONFIG_DRIVERS_IMU_ADIS16497=y
+imu/analog_devices/adis16448,CONFIG_DRIVERS_IMU_ANALOG_DEVICES_ADIS16448=y
+imu/analog_devices/adis16470,CONFIG_DRIVERS_IMU_ANALOG_DEVICES_ADIS16470=y
+imu/bosch/bmi055,CONFIG_DRIVERS_IMU_BOSCH_BMI055=y
+imu/bosch/bmi088,CONFIG_DRIVERS_IMU_BOSCH_BMI088=y
+imu/fxas21002c,CONFIG_DRIVERS_IMU_FXAS21002C=y
+imu/fxos8701cq,CONFIG_DRIVERS_IMU_FXOS8701CQ=y
+imu/invensense/icm20602,CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=y
+imu/invensense/icm20608g,CONFIG_DRIVERS_IMU_INVENSENSE_ICM20608G=y
+imu/invensense/icm20649,CONFIG_DRIVERS_IMU_INVENSENSE_ICM20649=y
+imu/invensense/icm20689,CONFIG_DRIVERS_IMU_INVENSENSE_ICM20689=y
+imu/invensense/icm20948,CONFIG_DRIVERS_IMU_INVENSENSE_ICM20948=y
+imu/invensense/icm40609d,CONFIG_DRIVERS_IMU_INVENSENSE_ICM40609D=y
+imu/invensense/icm42605,CONFIG_DRIVERS_IMU_INVENSENSE_ICM42605=y
+imu/invensense/icm42688p,CONFIG_DRIVERS_IMU_INVENSENSE_ICM42688P=y
+imu/invensense/mpu6000,CONFIG_DRIVERS_IMU_INVENSENSE_MPU6000=y
+imu/invensense/mpu6500,CONFIG_DRIVERS_IMU_INVENSENSE_MPU6500=y
+imu/invensense/mpu9250,CONFIG_DRIVERS_IMU_INVENSENSE_MPU9250=y
+imu/l3gd20,CONFIG_DRIVERS_IMU_L3GD20=y
+imu/lsm303d,CONFIG_DRIVERS_IMU_LSM303D=y
+imu/st,CONFIG_DRIVERS_IMU_ST=y
+irlock,CONFIG_DRIVERS_IRLOCK=y
+lights,CONFIG_COMMON_LIGHT=y
+lights/neopixel,CONFIG_DRIVERS_LIGHTS_NEOPIXEL=y
+lights/rgbled,CONFIG_DRIVERS_LIGHTS_RGBLED=y
+lights/rgbled_ncp5623c,CONFIG_DRIVERS_LIGHTS_RGBLED_NCP5623C=y
+lights/rgbled_pwm,CONFIG_DRIVERS_LIGHTS_RGBLED_PWM=y
+magnetometer,CONFIG_COMMON_MAGNETOMETER=y
+magnetometer/akm/ak09916,CONFIG_DRIVERS_MAGNETOMETER_AKM_AK09916=y
+magnetometer/akm/ak8963,CONFIG_DRIVERS_MAGNETOMETER_AKM_AK8963=y
+magnetometer/bosch/bmm150,CONFIG_DRIVERS_MAGNETOMETER_BOSCH_BMM150=y
+magnetometer/hmc5883,CONFIG_DRIVERS_MAGNETOMETER_HMC5883=y
+magnetometer/isentek/ist8308,CONFIG_DRIVERS_MAGNETOMETER_ISENTEK_IST8308=y
+magnetometer/isentek/ist8310,CONFIG_DRIVERS_MAGNETOMETER_ISENTEK_IST8310=y
+magnetometer/lis2mdl,CONFIG_DRIVERS_MAGNETOMETER_LIS2MDL=y
+magnetometer/lis3mdl,CONFIG_DRIVERS_MAGNETOMETER_LIS3MDL=y
+magnetometer/lsm303agr,CONFIG_DRIVERS_MAGNETOMETER_LSM303AGR=y
+magnetometer/lsm9ds1_mag,CONFIG_DRIVERS_MAGNETOMETER_LSM9DS1_MAG=y
+magnetometer/qmc5883l,CONFIG_DRIVERS_MAGNETOMETER_QMC5883L=y
+magnetometer/rm3100,CONFIG_DRIVERS_MAGNETOMETER_RM3100=y
+magnetometer/vtrantech/vcm1193l,CONFIG_DRIVERS_MAGNETOMETER_VTRANTECH_VCM1193L=y
+optical_flow,CONFIG_COMMON_OPTICAL_FLOW=y
+optical_flow/paw3902,CONFIG_DRIVERS_OPTICAL_FLOW_PAW3902=y
+optical_flow/paw3901,CONFIG_DRIVERS_OPTICAL_FLOW_PMW3901=y
+optical_flow/px4flow,CONFIG_DRIVERS_OPTICAL_FLOW_PX4FLOW=y
+optical_flow/thoneflow,CONFIG_DRIVERS_OPTICAL_FLOW_THONEFLOW=y
+osd,CONFIG_DRIVERS_OSD=y
+pca9685,CONFIG_DRIVERS_PCA9685=y
+pca9685_pwm_out,CONFIG_DRIVERS_PCA9685_PWM_OUT=y
+power_monitor/ina226,CONFIG_DRIVERS_POWER_MONITOR_INA226=y
+power_monitor/voxlpm,CONFIG_DRIVERS_POWER_MONITOR_VOXLPM=y
+pps_capture,CONFIG_DRIVERS_PPS_CAPTURE=y
+protocol_splitter,CONFIG_DRIVERS_PROTOCOL_SPLITTER=y
+pwm_input,CONFIG_DRIVERS_PWM_INPUT=y
+pwm_out_sim,CONFIG_DRIVERS_PWM_OUT_SIM=y
+pwm_out,CONFIG_DRIVERS_PWM_OUT=y
+px4io,CONFIG_DRIVERS_PX4IO=y
+rc_input,CONFIG_DRIVERS_RC_INPUT=y
+roboclaw,CONFIG_DRIVERS_ROBOCLAW=y
+rpi_rc_in,CONFIG_DRIVERS_RPI_RC_IN=y
+rpm,CONFIG_DRIVERS_RPM=y
+safety_button,CONFIG_DRIVERS_SAFETY_BUTTON=y
+smart_battery/batmon,CONFIG_DRIVERS_SMART_BATTERY_BATMON=y
+spektrum_rc,CONFIG_DRIVERS_SPEKTRUM_RC=y
+telemetry,CONFIG_DRIVERS_TELEMETRY=y
+test_ppm,CONFIG_DRIVERS_TEST_PPM=y
+tone_alarm,CONFIG_DRIVERS_TONE_ALARM=y
+uavcan,CONFIG_DRIVERS_UAVCAN=y
+uavcannode,CONFIG_DRIVERS_UAVCANNODE=y
+uavcannode_gps_demo,CONFIG_DRIVERS_UAVCANNODE_GPS_DEMO=y
+airship_att_control,CONFIG_MODULES_AIRSHIP_ATT_CONTROL=y
+airspeed_selector,CONFIG_MODULES_AIRSPEED_SELECTOR=y
+velocity_controller,CONFIG_MODULES_ANGULAR_VELOCITY_CONTROLLER=y
+attitude_estimator_q,CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=y
+battery_status,CONFIG_MODULES_BATTERY_STATUS=y
+camera_feedback,CONFIG_MODULES_CAMERA_FEEDBACK=y
+commander,CONFIG_MODULES_COMMANDER=y
+control_allocator,CONFIG_MODULES_CONTROL_ALLOCATOR=y
+dataman,CONFIG_MODULES_DATAMAN=y
+ekf2,CONFIG_MODULES_EKF2=y
+esc_battery,CONFIG_MODULES_ESC_BATTERY=y
+events,CONFIG_MODULES_EVENTS=y
+flight_mode_manager,CONFIG_MODULES_FLIGHT_MODE_MANAGER=y
+fw_att_control,CONFIG_MODULES_FW_ATT_CONTROL=y
+fw_pos_control_l1,CONFIG_MODULES_FW_POS_CONTROL_L1=y
+gyro_calibration,CONFIG_MODULES_GYRO_CALIBRATION=y
+gyro_fft,CONFIG_MODULES_GYRO_FFT=y
+land_detector,CONFIG_MODULES_LAND_DETECTOR=y
+landing_target_estimator,CONFIG_MODULES_LANDING_TARGET_ESTIMATOR=y
+load_mon,CONFIG_MODULES_LOAD_MON=y
+local_position_estimator,CONFIG_MODULES_LOCAL_POSITION_ESTIMATOR=y
+logger,CONFIG_MODULES_LOGGER=y
+mavlink,CONFIG_MODULES_MAVLINK=y
+mc_att_control,CONFIG_MODULES_MC_ATT_CONTROL=y
+mc_hover_thrust_estimator,CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=y
+mc_pos_control,CONFIG_MODULES_MC_POS_CONTROL=y
+mc_rate_control,CONFIG_MODULES_MC_RATE_CONTROL=y
+micrortps_bridge,CONFIG_MODULES_MICRORTPS_BRIDGE=y
+microdds_client,CONFIG_MODULES_MICRODDS_CLIENT=y
+navigator,CONFIG_MODULES_NAVIGATOR=y
+px4iofirmware,CONFIG_MODULES_PX4IOFIRMWARE=y
+rc_update,CONFIG_MODULES_RC_UPDATE=y
+replay,CONFIG_MODULES_REPLAY=y
+rover_pos_control,CONFIG_MODULES_ROVER_POS_CONTROL=y
+sensors,CONFIG_MODULES_SENSORS=y
+sih,CONFIG_MODULES_SIH=y
+simulator,CONFIG_MODULES_SIMULATOR=y
+temperature_compensation,CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
+uuv_att_control,CONFIG_MODULES_UUV_ATT_CONTROL=y
+uuv_pos_control,CONFIG_MODULES_UUV_POS_CONTROL=y
+gimbal,CONFIG_MODULES_GIMBAL=y
+vtol_att_control,CONFIG_MODULES_VTOL_ATT_CONTROL=y
+bl_update,CONFIG_SYSTEMCMDS_BL_UPDATE=y
+dmesg,CONFIG_SYSTEMCMDS_DMESG=y
+dumpfile,CONFIG_SYSTEMCMDS_DUMPFILE=y
+dyn,CONFIG_SYSTEMCMDS_DYN=y
+failure,CONFIG_SYSTEMCMDS_FAILURE=y
+gpio,CONFIG_SYSTEMCMDS_GPIO=y
+hardfault_log,CONFIG_SYSTEMCMDS_HARDFAULT_LOG=y
+i2cdetect,CONFIG_SYSTEMCMDS_I2CDETECT=y
+led_control,CONFIG_SYSTEMCMDS_LED_CONTROL=y
+mft,CONFIG_SYSTEMCMDS_MFT=y
+microbench,CONFIG_SYSTEMCMDS_MICROBENCH=y
+mixer,CONFIG_SYSTEMCMDS_MIXER=y
+motor_test,CONFIG_SYSTEMCMDS_MOTOR_TEST=y
+mtd,CONFIG_SYSTEMCMDS_MTD=y
+netman,CONFIG_SYSTEMCMDS_NETMAN=y
+nshterm,CONFIG_SYSTEMCMDS_NSHTERM=y
+param,CONFIG_SYSTEMCMDS_PARAM=y
+perf,CONFIG_SYSTEMCMDS_PERF=y
+pwm,CONFIG_SYSTEMCMDS_PWM=y
+reboot,CONFIG_SYSTEMCMDS_REBOOT=y
+reflect,CONFIG_SYSTEMCMDS_REFLECT=y
+sd_bench,CONFIG_SYSTEMCMDS_SD_BENCH=y
+serial_tet,CONFIG_SYSTEMCMDS_SERIAL_TEST=y
+shutdown,CONFIG_SYSTEMCMDS_SHUTDOWN=y
+system_time,CONFIG_SYSTEMCMDS_SYSTEM_TIME=y
+tests,CONFIG_SYSTEMCMDS_TESTS=y
+top,CONFIG_SYSTEMCMDS_TOP=y
+topic_listener,CONFIG_SYSTEMCMDS_TOPIC_LISTENER=y
+tune_control,CONFIG_SYSTEMCMDS_TUNE_CONTROL=y
+uorb,CONFIG_SYSTEMCMDS_UORB=y
+usb_connected,CONFIG_SYSTEMCMDS_USB_CONNECTED=y
+ver,CONFIG_SYSTEMCMDS_VER=y
+work_queue,CONFIG_SYSTEMCMDS_WORK_QUEUE=y
+dyn_hello,CONFIG_EXAMPLES_DYN_HELLO=y
+fake_gps,CONFIG_EXAMPLES_FAKE_GPS=y
+fake_gyro,CONFIG_EXAMPLES_FAKE_GYRO=y
+fake_imu,CONFIG_EXAMPLES_FAKE_IMU=y
+fake_magnetometer,CONFIG_EXAMPLES_FAKE_MAGNETOMETER=y
+fixedwing_control,CONFIG_EXAMPLES_FIXEDWING_CONTROL=y
+hello,CONFIG_EXAMPLES_HELLO=y
+hwtest,CONFIG_EXAMPLES_HWTEST=y
+matlab_csv_serial,CONFIG_EXAMPLES_MATLAB_CSV_SERIAL=y
+px4_mavlink_debug,CONFIG_EXAMPLES_PX4_MAVLINK_DEBUG=y
+px4_simple_app,CONFIG_EXAMPLES_PX4_SIMPLE_APP=y
+rover_steering_control,CONFIG_EXAMPLES_ROVER_STEERING_CONTROL=y
+uuv_example_app,CONFIG_EXAMPLES_UUV_EXAMPLE_APP=y
+work_item,CONFIG_EXAMPLES_WORK_ITEM=y
+add_compile_options(-Wno-narrowing),CONFIG_BOARD_COMPILE_DEFINITIONS="-Wno-narrowing"
+-D__PX4_LINUX,CONFIG_BOARD_LINUX=y
@@ -3019,7 +3019,7 @@ class MAVLink(object):
                time_boot_ms              : Timestamp (milliseconds since system boot) (uint32_t)
                press_abs                 : Absolute pressure (hectopascal) (float)
                press_diff                : Differential pressure 1 (hectopascal) (float)
-                temperature               : Temperature measurement (0.01 degrees Celsius) (int16_t)
+                temperature               : Temperature measurement (0.01 degrees celsius) (int16_t)

                '''
                msg = MAVLink_scaled_pressure_message(time_boot_ms, press_abs, press_diff, temperature)
@@ -3035,7 +3035,7 @@ class MAVLink(object):
                time_boot_ms              : Timestamp (milliseconds since system boot) (uint32_t)
                press_abs                 : Absolute pressure (hectopascal) (float)
                press_diff                : Differential pressure 1 (hectopascal) (float)
-                temperature               : Temperature measurement (0.01 degrees Celsius) (int16_t)
+                temperature               : Temperature measurement (0.01 degrees celsius) (int16_t)

                '''
                return self.send(self.scaled_pressure_encode(time_boot_ms, press_abs, press_diff, temperature))
@@ -4879,7 +4879,7 @@ class MAVLink(object):
                abs_pressure              : Absolute pressure in millibar (float)
                diff_pressure             : Differential pressure in millibar (float)
                pressure_alt              : Altitude calculated from pressure (float)
-                temperature               : Temperature in degrees Celsius (float)
+                temperature               : Temperature in degrees celsius (float)
                fields_updated            : Bitmask for fields that have updated since last message, bit 0 = xacc, bit 12: temperature (uint16_t)

                '''
@@ -4904,7 +4904,7 @@ class MAVLink(object):
                abs_pressure              : Absolute pressure in millibar (float)
                diff_pressure             : Differential pressure in millibar (float)
                pressure_alt              : Altitude calculated from pressure (float)
-                temperature               : Temperature in degrees Celsius (float)
+                temperature               : Temperature in degrees celsius (float)
                fields_updated            : Bitmask for fields that have updated since last message, bit 0 = xacc, bit 12: temperature (uint16_t)

                '''
--- a/Show More
+++ b/Show More
Author	SHA1	Message	Date
Daniel Agar	a1fa3cc699	WIP: common board init	2022-05-04 18:31:40 -04:00
Daniel Agar	2cc25f0763	boards: px4_fmu-v5/v5x init all I2C pins	2022-05-04 14:02:23 -04:00