The bulk of this change was tightly coupled and needed to be deleted in one pass. Some of the smaller changes were things that broke as a result of the initial purge and subsequently fixed by further eradicating unnecessary platform differences. Finally, I deleted any dead code I came across in the related files I touched while going through everything.
- DriverFramework (src/lib/DriverFramework submodule) completely removed
- added dspal submodule in qurt platform (was brought in via DriverFramework)
- all df wrapper drivers removed
- all boards using df wrapper drivers updated to use in tree equivalents
- unused empty arch/board.h on posix and qurt removed
- unused IOCTLs removed (pub block, priv, etc)
- Integrator delete methods only used from df wrapper drivers
- commander: sensor calibration use "NuttX version" everywhere for now
- sensors: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- battery_status: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- cdev cleanup conflicting typedefs and names with actual OS (pollevent_t, etc)
- load_mon and top remove from linux boards (unused)
- delete unused PX4_MAIN_FUNCTION
- delete unused getreg32 macro
- delete unused SIOCDEVPRIVATE define
- named each platform tasks consistently
- posix list_devices and list_topics removed (list_files now shows all virtual files)
Setting PTHREAD_EXPLICIT_SCHED was necessary on linux to create WQ threads with priorities relative to max, but unfortunately we can't rely pthread_attr_setinheritsched as it's dependent on system ulimit configuration or running privileged. Instead we can create the wq:manager at the maximum desired priority and allow each WQ thread to have a relative priority.
- fixed df_ltc2946_wrapper battery dependency
- fixed px4::atomic fetch_add for QuRT
- updated PX4 QuRT SPI wrapper to set bus frequency
- renamed "qurt-default" configs to just "qurt"
This target was never fully supported and is heavily dependent on a number of DriverFramework drivers that have no in tree equivalents (bebop bus, flow, rangefinder, etc). Deleting this will make it easier to fully drop DriverFramework shortly.
Main UAVCAN protocol handling and ESC updates run on the same thread/wq as
before. There are 2 WorkItems for separate scheduling of the 2, so that
ESC updates run in sync with actuator_control updates. UAVCAN is scheduled
at a fixed rate of 3ms (previously the poll timeout) and on each UAVCAN
bus event.
This leads to roughly the same behavior as before. CPU & RAM usage are
pretty much the same (tested on Pixhawk 4).
Testing done: Motors still work (with feedback), param changes and a
UAVCAN optical flow sensor.
and remove the px4_ prefix, except for px4_config.h.
command to update includes:
for k in app.h atomic.h cli.h console_buffer.h defines.h getopt.h i2c.h init.h log.h micro_hal.h module.h module_params.h param.h param_macros.h posix.h sem.h sem.hpp shmem.h shutdown.h tasks.h time.h workqueue.h; do for i in $(grep -rl 'include <px4_'$k src platforms boards); do sed -i 's/#include <px4_'$k'/#include <px4_platform_common\/'$k/ $i; done; done
for in $(grep -rl 'include <px4_config.h' src platforms boards); do sed -i 's/#include <px4_config.h/#include <px4_platform_common\/px4_config.h'/ $i; done
Transitional headers for submodules are added (px4_{defines,log,time}.h)
This could happen in the following cases:
- IRQ/publisher rate is faster than the processing rate, and therefore
WorkQueue::Add is called at a higher rate
- a long-running or stuck task that blocks the work queue a long time
Both cases are not expected to happen under 'normal' circumstances (if the
system runs as expected).
* adds a work_queue systemcmd that will bring a tree view of all active work queues and work items
* WorkQueues now track attached WorkItems and will shutdown when the last WorkItem is detached
Script to update include paths:
for i in $(grep -rl 'include <px4_work_queue' src platforms); do sed -i 's/#include <px4_work_queue/#include <px4_platform_common\/px4_work_queue/' $i; done
