In some cases, the fitness of the optimizer does not shrink at each
iteration, causing the "decreasing fitness check" to fail. This stops
the optimization and returns with sub-optimal, or unrealistic results.
- handle saving the mag bias per sensor (across all estimator instances using that mag) in sensors/vehicle_magnetometer
- this is now saving back to the actual mag calibration CAL_MAGn_OFF{X,Y,Z}
- ekf2 reset mag mag bias on any magnetometer or calibration change
- use Kalman filter scheme to update stored mag bias parameters using all available bias estimates for that sensor
Co-authored-by: Paul Riseborough <gncsolns@gmail.com>
- drivers/tone_alarm: move to ModuleBase and purge CDev (/dev/tone_alarm0)
- drivers/tone_alarm: only run on tune_control publication (or scheduled note) rather than continuously
- drivers/tone_alarm: use HRT to schedule tone stop (prevents potential disruption)
- msg/tune_control: add tune_id numbering
- systemcmds/tune_control: add "error" special case tune_id
- move all tune_control publication to new uORB::PublicationQueued<>
- start tone_alarm immediately after board defaults are loaded to fix potential startup issues
- for SITL (or other boards with no TONE output) print common messages (startup, error, etc)
- this allows the default priority to be set differently for internal/external sensors
- accel and gyro initialize default priority like mag in preparation for fully supporting external sensors
- fixes#15652
- use proper Mavlink MAV_CMD_FIXED_MAG_CAL_YAW command for initiating magnetometer quick cal
- MAV_CMD_FIXED_MAG_CAL_YAW allows specifying the yaw and optionally latitude and longitude if the vehicle doesn't have GPS
- remove all remaining IOCTLs for accel and gyro and handle all calibration entirely in sensors module with parameters
- sensor_accel and sensor_gyro are now always raw sensor data
- calibration procedures no longer need to first clear existing values before starting
- temperature calibration (TC) remove all scale (SCL) parameters
- gyro and baro scale are completely unused
- regular accel calibration scale can be used (CAL_ACC*_xSCALE) instead of TC scale
- create common uORB::PublicationBase
- uORB::PublicationQueued types are now type aliases
- ORB_PRIO use enum type everywhere to avoid accidental misuse
- PX4Accelerometer/PX4Gyroscope/etc driver libs explicitly advertise on construction, unadvertise on destruction. This is a workaround for any potential issues that might appear when accel/gyro cdev and uORB indexing doesn't align.
The bulk of this change was tightly coupled and needed to be deleted in one pass. Some of the smaller changes were things that broke as a result of the initial purge and subsequently fixed by further eradicating unnecessary platform differences. Finally, I deleted any dead code I came across in the related files I touched while going through everything.
- DriverFramework (src/lib/DriverFramework submodule) completely removed
- added dspal submodule in qurt platform (was brought in via DriverFramework)
- all df wrapper drivers removed
- all boards using df wrapper drivers updated to use in tree equivalents
- unused empty arch/board.h on posix and qurt removed
- unused IOCTLs removed (pub block, priv, etc)
- Integrator delete methods only used from df wrapper drivers
- commander: sensor calibration use "NuttX version" everywhere for now
- sensors: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- battery_status: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- cdev cleanup conflicting typedefs and names with actual OS (pollevent_t, etc)
- load_mon and top remove from linux boards (unused)
- delete unused PX4_MAIN_FUNCTION
- delete unused getreg32 macro
- delete unused SIOCDEVPRIVATE define
- named each platform tasks consistently
- posix list_devices and list_topics removed (list_files now shows all virtual files)
- if less than 6 sides are calibrated, keep the existing calibration and
update the offsets and scales
- if 2 sides are calibrated, estimate the offsets only (as this is enough
if a full calibration was done already, and the problem is not
constrained enough to estimate scales and offsets)
So it is independent from the number of configured sides.
Previously, each side would take longer if less than 6 sides were
calibrated.
Also fixes a bug: calibration_sides was used before it was updated, leading
to different behavior on consecutive calibrations with <6 sides.
Fixes a serious bug in combination with the HMC5883 driver (also used for
HMC5983): this driver estimates a scale in MAGIOCCALIBRATE and applies it.
The calibration routine does the calibration with that scale applied, and
then overwrites it, without considering it in any way.
Most other mag drivers only do some measurements and perform some checks
in MAGIOCCALIBRATE (but the result is just ignored).
and remove the px4_ prefix, except for px4_config.h.
command to update includes:
for k in app.h atomic.h cli.h console_buffer.h defines.h getopt.h i2c.h init.h log.h micro_hal.h module.h module_params.h param.h param_macros.h posix.h sem.h sem.hpp shmem.h shutdown.h tasks.h time.h workqueue.h; do for i in $(grep -rl 'include <px4_'$k src platforms boards); do sed -i 's/#include <px4_'$k'/#include <px4_platform_common\/'$k/ $i; done; done
for in $(grep -rl 'include <px4_config.h' src platforms boards); do sed -i 's/#include <px4_config.h/#include <px4_platform_common\/px4_config.h'/ $i; done
Transitional headers for submodules are added (px4_{defines,log,time}.h)
Fixes these invalid format strings:
- A `%d` for a pointer (replaced it by `%p`)
- A 0x%08x (and a 0x%0x8!) for a pointer (replaced by %p)
- 2 cases of `%d` for a `ssize_t` (replaced it by `%zi`)
- 1 case of a %u for an `int` (replaced by %i)
- 3 cases of %d for a `long` (replaced by %ld)
- 19 cases of `%d`, `%i`, `%u` or `%lu` for a `size_t` (replaced it by `%zu`)
- An unused formatting argument (removed it)
- A missing `%d` (added it)
- A missing `%s` (added it)
- 2 cases of `%llu` for a `uint64_t` (replaced it by `"%" PRIu64`)
- 6 cases of giving a string directly as format string (replaced it by `("%s", string)`)
- 2 cases of %*-s, which should probably have been %-*s.
(Looks like NuttX accepts (the invalid) %*-s, but other platforms don't.)
- A %04x for a `uint32_t` (replaced by "%04" PRIx32)
bresch