- interupt pin set active low and latch
- relax retry timeout if configure failed
- improve configured empty rate (sample rate) rounding
- fix RegisterCheck
- check FIFO count as part of full transfer and reset or adjust timing if necessary
- rename DRV_IMU_DEVTYPE_ICM20608 -> DRV_IMU_DEVTYPE_ICM20608G
- update to NuttX with stm32f4 and stm32f7 SPI DMA internal buffers
- remove explicit DMA buffer allocations from new IMU drivers
- restore original BOARD_DMA_ALLOC_POOL_SIZE
- decrease SPI DMA thresholds based on fmu-v2/v3/v4/v5 bench testing
Removes the calibration on startup, as these values were overwritten by
the system calibration values anyway.
So the only difference is that if all calibration scales were equal to 1,
the driver startup would have failed.
* msg: Add EKF-GSF yaw estimator logging data
* ecl: update to version with EKF-GSF yaw estimator
* ekf2: Add param control and logging for EKF-GSF yaw estimator
* logger: Add logging for EKF-GSF yaw esimtator
* MC_HTE: unitialize with hover_thrust parameter
* MC_HTE: constrain hover thrust setter between 0.1 and 0.9
* MC_HTE: integrate with land detector and velocity controller
* MCHoverThrustEstimator: Always publish an estimate even when not fusing measurements. This is required as the land detector and the position controller need to receive a hover thrust value.
* MC_HTE: use altitude agl threshold to start the estimator
local_position.z is relative to the origin of the EKF while dist_bottom
is above ground
Co-authored-by: bresch <brescianimathieu@gmail.com>
Chip-select and SPI initialization uses the new config, whereas the drivers
still use the existing defines.
The configuration in board_config.h can be removed after all drivers are
updated.
- reduces amount of board configuration required
- removes the cyclic dependency between io_timers_t and timer_io_channels_t
Fixes a bug in the fmuk66-v3 config: the 2. timer has 3 channels associated
not 2.
Fixes a bug in the modelai config: the 2. timer has 4 channels associated.
- it does nothing useful
- increases boot time by 2 seconds on pixhawk 4 due to a poll timeout:
IST8310 on I2C bus 3 at 0x0e (bus: 100 KHz, max: 400 KHz)
WARN [ist8310] ERROR: TIMEOUT 2
- this is a new module for temperature compensation that consolidates the functionality previously handled in the sensors module (calculating runtime thermal corrections) and the events module (online thermal calibration)
- by collecting this functionality into a single module we can optionally disable it on systems where it's not used and save some flash (if disabled at build time) or memory (disabled at run time)
- uses the FIFO and SPI DMA to transfer full raw data (8 kHz gyro, 4 kHz accel)
- new sensor messages for better visibility
- sensor_{accel, gyro}_fifo: full raw data for optional logging and analysis
- sensor_{accel, gyro}_status: metadata, clipping, etc
- currently not enabled by default
* FW attitude controller, FW position controller and VTOL attitude controller subscribe to airspeed_validated topic
* add possibility to switch off the airspeed valid checks
* remove airspeed valid checks from commander
* clean up of VTOL transition logic
* Airspeed Selector: remove dynamic allocation of airspeed validators (depending on number of connected sensors) but do it statically for the maximum number allowed. Check for number of connected sensors not only during start up, but always when vehicle is disarmed.
* Airspeed Selector: change work queue from lp to att_pos_ctrl as this module is safety-critical
* add airspeed selector to px4_fmu-v2 defaults
Beat Küng