Commit Graph
11 Commits
Author SHA1 Message Date
Daniel Agar d7c3e1066a uavcannode updates and px4_fmu-v4_cannode example
- drivers/uavcannode add baro, mag, gps publications
 - delete old px4_cannode-v1 board
 - add stripped down simple rcS for CAN nodes
2020-02-16 12:11:54 -05:00
Daniel Agar de4f594937 DriverFramework purge
The bulk of this change was tightly coupled and needed to be deleted in one pass. Some of the smaller changes were things that broke as a result of the initial purge and subsequently fixed by further eradicating unnecessary platform differences. Finally, I deleted any dead code I came across in the related files I touched while going through everything.

 - DriverFramework (src/lib/DriverFramework submodule) completely removed
 - added dspal submodule in qurt platform (was brought in via DriverFramework)
 - all df wrapper drivers removed
 - all boards using df wrapper drivers updated to use in tree equivalents
 - unused empty arch/board.h on posix and qurt removed
 - unused IOCTLs removed (pub block, priv, etc)
 - Integrator delete methods only used from df wrapper drivers
 - commander: sensor calibration use "NuttX version" everywhere for now
 - sensors: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
 - battery_status: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
 - cdev cleanup conflicting typedefs and names with actual OS (pollevent_t, etc)
 - load_mon and top remove from linux boards (unused)
 - delete unused PX4_MAIN_FUNCTION
 - delete unused getreg32 macro
 - delete unused SIOCDEVPRIVATE define
 - named each platform tasks consistently
 - posix list_devices and list_topics removed (list_files now shows all virtual files)
2020-01-13 14:07:03 -05:00
Daniel Agar 79dc676c8f mixer: move MixerGroup out of Mixer hierarchy and delete mixer.h header 2019-11-22 15:00:25 -05:00
David Sidrane e847698c9f PX4 System changes Supporting STM32H7
stm32:ToneAlarmInterfacePWM TIM15-TIM17 have a BDTR Register

common:board_crashdump Add H7 support

stm32/board_mcu_version:Support H7

PX4 ADC:Use 32 interface and resoution abstraction

Added PX4 stm32h7 ADC driver

stm32h7:adc fix ADC ready check

fmu: handle BOARD_HAS_PWM==5

cmake: improve error handling for NuttX olddefconfig failures

WorkQueueManager:Quiet loadmon stack warning

camera_trigger:GPIO support < 6 GPIO

Adjust stack sizes (under hw stack check)

PX4 System changes Supporting STM32H7 PX4IO Driver

aerotenna_ocpoc:ADC add px4_arch_adc_dn_fullcount

init.cmake:Track Upstream change needing Make.def at config time

PX4 System changes Supporting STM32H7

NuttX CMakeLists.txt Track upstream changes

Common board_crashdump add header and px4 config

NuttX simplify callinb make libapps

Use UINT32_MAX for error return

drivers:uavcannode NuttX chip is now hardware

drivers:uavcanesc NuttX chip is now hardware

px4io:Avoid Race on AP to PX4 IO upgrade
2019-11-16 11:43:42 +01:00
Daniel Agar 1c4e854f93 cmake don't build param "c" files and remove param defines
- these aren't actual source code
2019-11-11 10:25:42 -05:00
Beat Küng 5dff065ec5 uavcan: move to work queue and use MixingOutput
Main UAVCAN protocol handling and ESC updates run on the same thread/wq as
before. There are 2 WorkItems for separate scheduling of the 2, so that
ESC updates run in sync with actuator_control updates. UAVCAN is scheduled
at a fixed rate of 3ms (previously the poll timeout) and on each UAVCAN
bus event.
This leads to roughly the same behavior as before. CPU & RAM usage are
pretty much the same (tested on Pixhawk 4).

Testing done: Motors still work (with feedback), param changes and a
UAVCAN optical flow sensor.
2019-11-07 10:40:03 +01:00
Beat Küng b7a480b45b refactor uavcan: add stm32 and kinetis drivers directly 2019-11-07 10:40:03 +01:00
Beat Küng 0db0981b1b uavcan: remove actuator_direct (no publisher) 2019-11-07 10:40:03 +01:00
Beat Küng 3198610f85 src/platforms: move all headers to platforms/common/include/px4_platform_common
and remove the px4_ prefix, except for px4_config.h.

command to update includes:
for k in app.h atomic.h cli.h console_buffer.h defines.h getopt.h i2c.h init.h log.h micro_hal.h module.h module_params.h param.h param_macros.h posix.h sem.h sem.hpp shmem.h shutdown.h tasks.h time.h workqueue.h; do for i in $(grep -rl 'include <px4_'$k src platforms boards); do sed -i 's/#include <px4_'$k'/#include <px4_platform_common\/'$k/ $i; done; done
for in $(grep -rl 'include <px4_config.h' src platforms boards); do sed -i 's/#include <px4_config.h/#include <px4_platform_common\/px4_config.h'/ $i; done

Transitional headers for submodules are added (px4_{defines,log,time}.h)
2019-10-30 11:48:47 +01:00
Daniel Agar b35d048566 cmake enable -Wcast-align and disable per module 2019-03-16 11:47:15 -04:00
Daniel Agar 75b2053243 move uavcan from modules to drivers 2018-12-04 01:06:54 -05:00