* uORB orb_stat() and update(uint64_t *time, void *dst) are now obsolete and have been deleted
* mavlink messages add more advertised checks in streams get_size() check to improve data rate calculation across different scenarios
This avoids the need for recalibration, and also cleans up other driver
ID's (merge separate accel/gyro).
The SPI address was previously set to a board-specific (arbitrary) value,
and is now set to 0. This will allow extending for multiple sensors of the
same type on the same bus.
Chip-select and SPI initialization uses the new config, whereas the drivers
still use the existing defines.
The configuration in board_config.h can be removed after all drivers are
updated.
- refactor Run() into simple state machine
- perform reset and configuration in sensor bus thread
- when using data ready interrupt skip checking FIFO count
- fix periodic temperature sampling (rate limit to 1 Hz)
- refactor Run() into simple state machine
- perform reset and configuration in sensor bus thread
- when using data ready interrupt skip checking FIFO count
- fix periodic temperature sampling (rate limit to 1 Hz)
- refactor Run() into simple state machine
- perform reset and configuration in sensor bus thread
- when using data ready interrupt skip checking FIFO count
- fix periodic temperature sampling (rate limit to 1 Hz)
- refactor Run() into simple state machine
- perform reset and configuration in sensor bus thread
- when using data ready interrupt skip checking FIFO count
* Introduce "px4_arch_adc_reference_v"
* Revert "Introduce "px4_arch_adc_reference_v""
This reverts commit 93691fbbd55a1b8da8c190e225b318067d90399b.
* use structure to return sample count and vref at the same time
* Revert "use structure to return sample count and vref at the same time"
This reverts commit 9cfd1c173cda51495f766a3f678c2202d67725fd.
* Revert "Revert "Introduce "px4_arch_adc_reference_v"""
This reverts commit edb7f7603e4471163ffb0fc6fc62ad2e30336e91.
* fix missed reference
* remove unecessary channel specific vref
* Update src/drivers/drv_adc.h
Co-Authored-By: David Sidrane <David.Sidrane@Nscdg.com>
* Update src/drivers/drv_adc.h
Co-Authored-By: David Sidrane <David.Sidrane@Nscdg.com>
* Introduce BOARD_ADC_POS_REF_V
Co-authored-by: David Sidrane <David.Sidrane@Nscdg.com>
Regression from https://github.com/PX4/Firmware/pull/13613.
VEHICLE_CMD_COMPONENT_ARM_DISARM from CLI would enter the
ARMING_STATE_IN_AIR_RESTORE logic. This was never intended for disarming
(and leads to state machine transition failures), and IMO it is also not
intended for commands from CLI.
- checked register mechanism and simple watchdog
- driver checks for errors gradually and can reconfigure itself
- respect IMU_GYRO_RATEMAX at the driver level
- fixed sensor INT16_MIN and INT16_MAX handling (y & z axis are flipped before publishing)
- checked register mechanism and simple watchdog
- driver checks for errors gradually and can reconfigure itself
- respect IMU_GYRO_RATEMAX at the driver level
- fixed sensor INT16_MIN and INT16_MAX handling (y & z axis are flipped before publishing)
- checked register mechanism and simple watchdog
- driver checks for errors gradually and can reconfigure itself
- respect IMU_GYRO_RATEMAX at the driver level
- fixed sensor INT16_MIN and INT16_MAX handling (y & z axis are flipped before publishing)
- checked register mechanism and simple watchdog
- driver checks for errors gradually and can reconfigure itself
- respect IMU_GYRO_RATEMAX at the driver level
- fixed sensor INT16_MIN and INT16_MAX handling (y & z axis are flipped before publishing)
- increased sensor_gyro_fifo max size (enables running the driver much slower, but still transferring all raw data)
- PX4Accelerometer/PX4Gyroscope remove unnecessary memsets
- it does nothing useful
- increases boot time by 2 seconds on pixhawk 4 due to a poll timeout:
IST8310 on I2C bus 3 at 0x0e (bus: 100 KHz, max: 400 KHz)
WARN [ist8310] ERROR: TIMEOUT 2
Beat Küng