* FW attitude controller, FW position controller and VTOL attitude controller subscribe to airspeed_validated topic
* add possibility to switch off the airspeed valid checks
* remove airspeed valid checks from commander
* clean up of VTOL transition logic
* Airspeed Selector: remove dynamic allocation of airspeed validators (depending on number of connected sensors) but do it statically for the maximum number allowed. Check for number of connected sensors not only during start up, but always when vehicle is disarmed.
* Airspeed Selector: change work queue from lp to att_pos_ctrl as this module is safety-critical
* add airspeed selector to px4_fmu-v2 defaults
and remove the px4_ prefix, except for px4_config.h.
command to update includes:
for k in app.h atomic.h cli.h console_buffer.h defines.h getopt.h i2c.h init.h log.h micro_hal.h module.h module_params.h param.h param_macros.h posix.h sem.h sem.hpp shmem.h shutdown.h tasks.h time.h workqueue.h; do for i in $(grep -rl 'include <px4_'$k src platforms boards); do sed -i 's/#include <px4_'$k'/#include <px4_platform_common\/'$k/ $i; done; done
for in $(grep -rl 'include <px4_config.h' src platforms boards); do sed -i 's/#include <px4_config.h/#include <px4_platform_common\/px4_config.h'/ $i; done
Transitional headers for submodules are added (px4_{defines,log,time}.h)
* adds a work_queue systemcmd that will bring a tree view of all active work queues and work items
* WorkQueues now track attached WorkItems and will shutdown when the last WorkItem is detached
Script to update include paths:
for i in $(grep -rl 'include <px4_work_queue' src platforms); do sed -i 's/#include <px4_work_queue/#include <px4_platform_common\/px4_work_queue/' $i; done
- VT_MOT_COUNT assumed that motors were always the first outputs. This
does not have to be true always. VT_MOT_ID allows to specify precisely how
many motors we have for hovering and to which channel they are connected.
Signed-off-by: RomanBapst <bapstroman@gmail.com>
This changes the enums used for various VTOL states to enum classes
which makes them type-safe and should avoid shadowing.
This change was motivated by a Clang warning about shadowing of the
enum const TRANSITION_TO_FW which was declared twice, once in
vtol_type.h and once in standard.h.
This change only removes the shadowing but presumably these enums could
be cleaned up and consolidated further.
* VTOL trans: changed that now in transition for both MC and FW the corresponding (correct) attitude controller is running
* attitude setpoint for stabilized mode is generated by tailsitter.cpp
* reset yaw setpoint during transition to avoid big yaw errors after
transition back to hover
* VT_TYPE parameter: added "reboot required" metadata
Mark V19_VT_ROLLDIR @category system
Throttle down mavlink critical msg
Send 0 actuator_output for safety
VTOL: unset v1.9 roll direction safety check param for builtin airframes
* attitude and rate setpoint message: use 3D array for thrust demand
* FixedWingAttitudeControl: rework airspeed scaling
* move airspeed and scaling calculation into separate method
* if vtol in hover and airspeed disabled use minimum airspeed instead of trim airspeed
- do not set zero throttle during the entire back-transition because otherwise
we need to make the back-transition really short
- added ramping up of throttle setpoint during backtransition to avoid
step inputs
- back-transition ends after back-transition time and not when motors are fully
rotated updwards. previously the vehicle would enter hover mode at high speed
which was not handled well by the mc position controller
Signed-off-by: Roman <bapstroman@gmail.com>
Silvan Fuhrer