mirror of
https://gitee.com/mirrors_PX4/PX4-Autopilot.git
synced 2026-11-16 08:21:36 +08:00
WIP: device tree MVP
This commit is contained in:
@@ -0,0 +1,41 @@
|
||||
/*
|
||||
* Copyright (c) 2020 DENX Software Engineering GmbH
|
||||
*
|
||||
* SPDX-License-Identifier: Apache-2.0
|
||||
*/
|
||||
|
||||
#include <mem.h>
|
||||
#include <nxp/nxp_k6x.dtsi>
|
||||
|
||||
&flash0 {
|
||||
reg = <0x00000000 DT_SIZE_M(2)>;
|
||||
};
|
||||
|
||||
/ {
|
||||
soc {
|
||||
lpuart0: lpuart@400c4000 {
|
||||
compatible = "nxp,kinetis-lpuart";
|
||||
reg = <0x400c4000 0x14>;
|
||||
interrupts = <86 0>;
|
||||
clocks = <&sim KINETIS_SIM_CORESYS_CLK 0x1038 20>;
|
||||
label = "LPUART_0";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
flexcan1: can@400a4000 {
|
||||
compatible = "nxp,kinetis-flexcan";
|
||||
reg = <0x400a4000 0x1000>;
|
||||
interrupts = <94 0>, <95 0>, <96 0>, <97 0>, <98 0>, <99 0>;
|
||||
interrupt-names = "mb-0-15", "bus-off", "error", "tx-warning",
|
||||
"rx-warning", "wake-up";
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x1030 4>;
|
||||
clk-source = <1>;
|
||||
label = "CAN_1";
|
||||
sjw = <1>;
|
||||
prop-seg = <1>;
|
||||
phase-seg1 = <3>;
|
||||
phase-seg2 = <2>;
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
};
|
||||
@@ -0,0 +1,572 @@
|
||||
/* SPDX-License-Identifier: Apache-2.0 */
|
||||
|
||||
#include <mem.h>
|
||||
#include <arm/armv7-m.dtsi>
|
||||
#include <dt-bindings/clock/kinetis_sim.h>
|
||||
#include <dt-bindings/clock/kinetis_mcg.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/i2c/i2c.h>
|
||||
|
||||
/ {
|
||||
aliases {
|
||||
watchdog0 = &wdog;
|
||||
};
|
||||
|
||||
chosen {
|
||||
zephyr,entropy = &rnga;
|
||||
zephyr,flash-controller = &ftfe;
|
||||
};
|
||||
|
||||
cpus {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
cpu0: cpu@0 {
|
||||
device_type = "cpu";
|
||||
compatible = "arm,cortex-m4f";
|
||||
reg = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
/* The on-chip SRAM is split into SRAM_L and SRAM_U regions that form a
|
||||
* contiguous block in the memory map, however misaligned accesses
|
||||
* across the 0x2000_0000 boundary are not supported in the Arm
|
||||
* Cortex-M4 architecture. For clarity and to avoid the temptation for
|
||||
* someone to extend sram0 without solving this issue, we define two
|
||||
* separate memory nodes here and only use the upper one for now. A
|
||||
* potential solution has been proposed in binutils:
|
||||
* https://sourceware.org/ml/binutils/2017-02/msg00250.html
|
||||
*/
|
||||
sram_l: memory@1fff0000 {
|
||||
compatible = "mmio-sram";
|
||||
reg = <0x1fff0000 DT_SIZE_K(64)>;
|
||||
};
|
||||
|
||||
sram0: memory@20000000 {
|
||||
compatible = "mmio-sram";
|
||||
reg = <0x20000000 DT_SIZE_K(192)>;
|
||||
};
|
||||
|
||||
temp0: temp0 {
|
||||
compatible = "nxp,kinetis-temperature";
|
||||
io-channels = <&adc0 26>, <&adc0 27>;
|
||||
io-channel-names = "SENSOR", "BANDGAP";
|
||||
bandgap-voltage = <1000000>;
|
||||
vtemp25 = <716000>;
|
||||
sensor-slope-cold = <1620>;
|
||||
sensor-slope-hot = <1620>;
|
||||
label = "TEMP0";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
temp1: temp1 {
|
||||
compatible = "nxp,kinetis-temperature";
|
||||
io-channels = <&adc1 26>, <&adc1 27>;
|
||||
io-channel-names = "SENSOR", "BANDGAP";
|
||||
bandgap-voltage = <1000000>;
|
||||
vtemp25 = <716000>;
|
||||
sensor-slope-cold = <1620>;
|
||||
sensor-slope-hot = <1620>;
|
||||
label = "TEMP1";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
soc {
|
||||
mpu: mpu@4000d000 {
|
||||
compatible = "nxp,k64f-mpu";
|
||||
reg = <0x4000d000 0x824>;
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
mcg: clock-controller@40064000 {
|
||||
compatible = "nxp,kinetis-mcg";
|
||||
reg = <0x40064000 0xd>;
|
||||
label = "MCG";
|
||||
#clock-cells = <1>;
|
||||
};
|
||||
|
||||
osc: clock-controller@40065000 {
|
||||
compatible = "nxp,k64f-osc";
|
||||
reg = <0x40065000 0x4>;
|
||||
|
||||
enable-external-reference;
|
||||
};
|
||||
|
||||
rtc: rtc@4003d000 {
|
||||
compatible = "nxp,kinetis-rtc";
|
||||
reg = <0x4003d000 0x1000>;
|
||||
interrupts = <46 0>, <47 0>;
|
||||
interrupt-names = "alarm", "seconds";
|
||||
clock-frequency = <32768>;
|
||||
prescaler = <32768>;
|
||||
label = "RTC_0";
|
||||
};
|
||||
|
||||
sim: sim@40047000 {
|
||||
compatible = "nxp,kinetis-sim";
|
||||
reg = <0x40047000 0x1060>;
|
||||
label = "SIM";
|
||||
#clock-cells = <3>;
|
||||
|
||||
core_clk {
|
||||
compatible = "fixed-factor-clock";
|
||||
clocks = <&mcg KINETIS_MCG_OUT_CLK>;
|
||||
clock-div = <1>;
|
||||
#clock-cells = <0>;
|
||||
};
|
||||
|
||||
bus_clk {
|
||||
compatible = "fixed-factor-clock";
|
||||
clocks = <&mcg KINETIS_MCG_OUT_CLK>;
|
||||
clock-div = <2>;
|
||||
#clock-cells = <0>;
|
||||
};
|
||||
|
||||
flexbus_clk {
|
||||
compatible = "fixed-factor-clock";
|
||||
clocks = <&mcg KINETIS_MCG_OUT_CLK>;
|
||||
clock-div = <3>;
|
||||
#clock-cells = <0>;
|
||||
};
|
||||
|
||||
flash_clk {
|
||||
compatible = "fixed-factor-clock";
|
||||
clocks = <&mcg KINETIS_MCG_OUT_CLK>;
|
||||
clock-div = <5>;
|
||||
#clock-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
ftfe: flash-controller@40020000 {
|
||||
compatible = "nxp,kinetis-ftfe";
|
||||
label = "FLASH_CTRL";
|
||||
reg = <0x40020000 0x18>;
|
||||
interrupts = <18 0>, <19 0>;
|
||||
interrupt-names = "command-complete", "read-collision";
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
flash0: flash@0 {
|
||||
compatible = "soc-nv-flash";
|
||||
label = "MCUX_FLASH";
|
||||
reg = <0 DT_SIZE_M(1)>;
|
||||
erase-block-size = <4096>;
|
||||
write-block-size = <8>;
|
||||
};
|
||||
};
|
||||
|
||||
i2c0: i2c@40066000 {
|
||||
compatible = "nxp,kinetis-i2c";
|
||||
clock-frequency = <I2C_BITRATE_STANDARD>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x40066000 0x1000>;
|
||||
interrupts = <24 0>;
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x1034 6>;
|
||||
label = "I2C_0";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
i2c1: i2c@40067000 {
|
||||
compatible = "nxp,kinetis-i2c";
|
||||
clock-frequency = <I2C_BITRATE_STANDARD>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x40067000 0x1000>;
|
||||
interrupts = <25 0>;
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x1034 7>;
|
||||
label = "I2C_1";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
i2c2: i2c@400e6000 {
|
||||
compatible = "nxp,kinetis-i2c";
|
||||
clock-frequency = <I2C_BITRATE_STANDARD>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x400e6000 0x1000>;
|
||||
interrupts = <74 0>;
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x1028 6>;
|
||||
label = "I2C_2";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
uart0: uart@4006a000 {
|
||||
compatible = "nxp,kinetis-uart";
|
||||
reg = <0x4006a000 0x1000>;
|
||||
interrupts = <31 0>, <32 0>;
|
||||
interrupt-names = "status", "error";
|
||||
clocks = <&sim KINETIS_SIM_CORESYS_CLK 0x1034 10>;
|
||||
label = "UART_0";
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
uart1: uart@4006b000 {
|
||||
compatible = "nxp,kinetis-uart";
|
||||
reg = <0x4006b000 0x1000>;
|
||||
interrupts = <33 0>, <34 0>;
|
||||
interrupt-names = "status", "error";
|
||||
clocks = <&sim KINETIS_SIM_CORESYS_CLK 0x1034 11>;
|
||||
label = "UART_1";
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
uart2: uart@4006c000 {
|
||||
compatible = "nxp,kinetis-uart";
|
||||
reg = <0x4006c000 0x1000>;
|
||||
interrupts = <35 0>, <36 0>;
|
||||
interrupt-names = "status", "error";
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x1034 12>;
|
||||
label = "UART_2";
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
uart3: uart@4006d000 {
|
||||
compatible = "nxp,kinetis-uart";
|
||||
reg = <0x4006d000 0x1000>;
|
||||
interrupts = <37 0>, <38 0>;
|
||||
interrupt-names = "status", "error";
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x1034 13>;
|
||||
label = "UART_3";
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
uart4: uart@400ea000 {
|
||||
compatible = "nxp,kinetis-uart";
|
||||
reg = <0x400ea000 0x1000>;
|
||||
interrupts = <66 0>, <67 0>;
|
||||
interrupt-names = "status", "error";
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x1028 10>;
|
||||
label = "UART_4";
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
uart5: uart@400eb000 {
|
||||
compatible = "nxp,kinetis-uart";
|
||||
reg = <0x400eb000 0x1000>;
|
||||
interrupts = <68 0>, <69 0>;
|
||||
interrupt-names = "status", "error";
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x1028 11>;
|
||||
label = "UART_5";
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
porta: pinmux@40049000 {
|
||||
compatible = "nxp,kinetis-pinmux";
|
||||
reg = <0x40049000 0xd0>;
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x1038 9>;
|
||||
};
|
||||
|
||||
portb: pinmux@4004a000 {
|
||||
compatible = "nxp,kinetis-pinmux";
|
||||
reg = <0x4004a000 0xd0>;
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x1038 10>;
|
||||
};
|
||||
|
||||
portc: pinmux@4004b000 {
|
||||
compatible = "nxp,kinetis-pinmux";
|
||||
reg = <0x4004b000 0xd0>;
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x1038 11>;
|
||||
};
|
||||
|
||||
portd: pinmux@4004c000 {
|
||||
compatible = "nxp,kinetis-pinmux";
|
||||
reg = <0x4004c000 0xd0>;
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x1038 12>;
|
||||
};
|
||||
|
||||
porte: pinmux@4004d000 {
|
||||
compatible = "nxp,kinetis-pinmux";
|
||||
reg = <0x4004d000 0xd0>;
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x1038 13>;
|
||||
};
|
||||
|
||||
gpioa: gpio@400ff000 {
|
||||
compatible = "nxp,kinetis-gpio";
|
||||
status = "disabled";
|
||||
reg = <0x400ff000 0x40>;
|
||||
interrupts = <59 2>;
|
||||
label = "GPIO_0";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
nxp,kinetis-port = <&porta>;
|
||||
};
|
||||
|
||||
gpiob: gpio@400ff040 {
|
||||
compatible = "nxp,kinetis-gpio";
|
||||
status = "disabled";
|
||||
reg = <0x400ff040 0x40>;
|
||||
interrupts = <60 2>;
|
||||
label = "GPIO_1";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
nxp,kinetis-port = <&portb>;
|
||||
};
|
||||
|
||||
gpioc: gpio@400ff080 {
|
||||
compatible = "nxp,kinetis-gpio";
|
||||
status = "disabled";
|
||||
reg = <0x400ff080 0x40>;
|
||||
interrupts = <61 2>;
|
||||
label = "GPIO_2";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
nxp,kinetis-port = <&portc>;
|
||||
};
|
||||
|
||||
gpiod: gpio@400ff0c0 {
|
||||
compatible = "nxp,kinetis-gpio";
|
||||
status = "disabled";
|
||||
reg = <0x400ff0c0 0x40>;
|
||||
interrupts = <62 2>;
|
||||
label = "GPIO_3";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
nxp,kinetis-port = <&portd>;
|
||||
};
|
||||
|
||||
gpioe: gpio@400ff100 {
|
||||
compatible = "nxp,kinetis-gpio";
|
||||
status = "disabled";
|
||||
reg = <0x400ff100 0x40>;
|
||||
interrupts = <63 2>;
|
||||
label = "GPIO_4";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
nxp,kinetis-port = <&porte>;
|
||||
};
|
||||
|
||||
spi0: spi@4002c000 {
|
||||
compatible = "nxp,kinetis-dspi";
|
||||
reg = <0x4002c000 0x88>;
|
||||
interrupts = <26 3>;
|
||||
label = "SPI_0";
|
||||
dmas = <&edma0 0 14>, <&edma0 0 15>;
|
||||
dma-names = "rx", "tx";
|
||||
rx-fifo-size = <4>;
|
||||
tx-fifo-size = <4>;
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x103C 12>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
spi1: spi@4002d000 {
|
||||
compatible = "nxp,kinetis-dspi";
|
||||
reg = <0x4002d000 0x88>;
|
||||
interrupts = <27 3>;
|
||||
label = "SPI_1";
|
||||
dmas = <&edma0 0 16>, <&edma0 0 16>;
|
||||
dma-names = "rx", "tx";
|
||||
rx-fifo-size = <1>;
|
||||
tx-fifo-size = <1>;
|
||||
nxp,rx-tx-chn-share;
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x103C 13>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
spi2: spi@400ac000 {
|
||||
compatible = "nxp,kinetis-dspi";
|
||||
reg = <0x400ac000 0x88>;
|
||||
interrupts = <65 3>;
|
||||
label = "SPI_2";
|
||||
dmas = <&edma0 0 17>, <&edma0 0 17>;
|
||||
dma-names = "rx", "tx";
|
||||
rx-fifo-size = <1>;
|
||||
tx-fifo-size = <1>;
|
||||
nxp,rx-tx-chn-share;
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x1030 12>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
wdog: watchdog@40052000 {
|
||||
compatible = "nxp,kinetis-wdog";
|
||||
reg = <0x40052000 16>;
|
||||
interrupts = <22 0>;
|
||||
clocks = <&sim KINETIS_SIM_LPO_CLK 0 0>;
|
||||
label = "WDT_0";
|
||||
};
|
||||
|
||||
ftm0: ftm@40038000{
|
||||
compatible = "nxp,kinetis-ftm";
|
||||
reg = <0x40038000 0x98>;
|
||||
interrupts = <42 0>;
|
||||
clocks = <&mcg KINETIS_MCG_FIXED_FREQ_CLK>;
|
||||
prescaler = <16>;
|
||||
label = "FTM_0";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
ftm1: ftm@40039000{
|
||||
compatible = "nxp,kinetis-ftm";
|
||||
reg = <0x40039000 0x98>;
|
||||
interrupts = <43 0>;
|
||||
clocks = <&mcg KINETIS_MCG_FIXED_FREQ_CLK>;
|
||||
prescaler = <16>;
|
||||
label = "FTM_1";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
ftm2: ftm@4003a000{
|
||||
compatible = "nxp,kinetis-ftm";
|
||||
reg = <0x4003a000 0x98>;
|
||||
interrupts = <44 0>;
|
||||
clocks = <&mcg KINETIS_MCG_FIXED_FREQ_CLK>;
|
||||
prescaler = <16>;
|
||||
label = "FTM_2";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
ftm3: ftm@400b9000{
|
||||
compatible = "nxp,kinetis-ftm";
|
||||
reg = <0x400b9000 0x98>;
|
||||
interrupts = <71 0>;
|
||||
clocks = <&mcg KINETIS_MCG_FIXED_FREQ_CLK>;
|
||||
prescaler = <16>;
|
||||
label = "FTM_3";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
adc0: adc@4003b000{
|
||||
compatible = "nxp,kinetis-adc16";
|
||||
reg = <0x4003b000 0x70>;
|
||||
clocks = <&sim KINETIS_SIM_SIM_SOPT7 0 0xF>,
|
||||
<&sim KINETIS_SIM_SIM_SOPT7 7 0x80>;
|
||||
dmas = <&edma0 0 40>;
|
||||
dma-names = "adc0";
|
||||
clk-source = <0>;
|
||||
interrupts = <39 0>;
|
||||
label = "ADC_0";
|
||||
status = "disabled";
|
||||
#io-channel-cells = <1>;
|
||||
};
|
||||
|
||||
adc1: adc@400bb000{
|
||||
compatible = "nxp,kinetis-adc16";
|
||||
reg = <0x400bb000 0x70>;
|
||||
clocks = <&sim KINETIS_SIM_SIM_SOPT7 8 0xF00>,
|
||||
<&sim KINETIS_SIM_SIM_SOPT7 15 0x8000>;
|
||||
dmas = <&edma0 0 41>;
|
||||
dma-names = "adc1";
|
||||
clk-source = <0>;
|
||||
interrupts = <73 0>;
|
||||
label = "ADC_1";
|
||||
status = "disabled";
|
||||
#io-channel-cells = <1>;
|
||||
};
|
||||
|
||||
dac0: dac@400cc000 {
|
||||
compatible = "nxp,kinetis-dac";
|
||||
reg = <0x400cc000 0x1000>;
|
||||
interrupts = <56 0>;
|
||||
voltage-reference = <1>;
|
||||
label = "DAC_0";
|
||||
status = "disabled";
|
||||
#io-channel-cells = <1>;
|
||||
};
|
||||
|
||||
dac1: dac@400cd000 {
|
||||
compatible = "nxp,kinetis-dac";
|
||||
reg = <0x400cd000 0x1000>;
|
||||
interrupts = <72 0>;
|
||||
voltage-reference = <1>;
|
||||
label = "DAC_1";
|
||||
status = "disabled";
|
||||
#io-channel-cells = <1>;
|
||||
};
|
||||
|
||||
usbotg: usbd@40072000 {
|
||||
compatible = "nxp,kinetis-usbd";
|
||||
reg = <0x40072000 0x1000>;
|
||||
interrupts = <53 1>;
|
||||
interrupt-names = "usb_otg";
|
||||
num-bidir-endpoints = <16>;
|
||||
status = "disabled";
|
||||
label = "USBD";
|
||||
};
|
||||
|
||||
enet: ethernet@400c0000 {
|
||||
compatible = "nxp,kinetis-ethernet";
|
||||
reg = <0x400c0000 0x620>;
|
||||
interrupts = <83 0>, <84 0>, <85 0>;
|
||||
interrupt-names = "TX", "RX", "ERR";
|
||||
status = "disabled";
|
||||
label = "ETH_0";
|
||||
clocks = <&sim KINETIS_SIM_CORESYS_CLK 0 0>;
|
||||
ptp {
|
||||
compatible = "nxp,kinetis-ptp";
|
||||
status = "disabled";
|
||||
interrupts = <82 0>;
|
||||
interrupt-names = "IEEE1588_TMR";
|
||||
};
|
||||
};
|
||||
|
||||
rnga: random@40029000 {
|
||||
compatible = "nxp,kinetis-rnga";
|
||||
reg = <0x40029000 0x1000>;
|
||||
status = "okay";
|
||||
interrupts = <23 0>;
|
||||
label = "RNGA";
|
||||
};
|
||||
|
||||
flexcan0: can@40024000 {
|
||||
compatible = "nxp,kinetis-flexcan";
|
||||
reg = <0x40024000 0x1000>;
|
||||
interrupts = <75 0>, <76 0>, <77 0>, <78 0>, <79 0>, <80 0>;
|
||||
interrupt-names = "mb-0-15", "bus-off", "error", "tx-warning", "rx-warning", "wake-up";
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x103C 4>;
|
||||
clk-source = <1>;
|
||||
label = "CAN_0";
|
||||
sjw = <1>;
|
||||
sample-point = <875>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
edma0: dma-controller@40008000 {
|
||||
#dma-cells = <2>;
|
||||
compatible = "nxp,mcux-edma";
|
||||
dma-channels = <16>;
|
||||
dma-requests = <64>;
|
||||
nxp,mem2mem;
|
||||
reg = <0x40008000 0x1000>,
|
||||
<0x40021000 0x1000>;
|
||||
interrupts = <0 0>, <1 0>, <2 0>, <3 0>,
|
||||
<4 0>, <5 0>, <6 0>, <7 0>,
|
||||
<8 0>, <9 0>, <10 0>, <11 0>,
|
||||
<12 0>, <13 0>, <14 0>, <15 0>,
|
||||
<16 0>;
|
||||
clocks = <&sim KINETIS_SIM_DMA_CLK 0x1040 0x00000002>,
|
||||
<&sim KINETIS_SIM_DMAMUX_CLK 0x103C 0x00000002>;
|
||||
status = "disabled";
|
||||
label = "DMA_0";
|
||||
};
|
||||
|
||||
pit0: pit@40037000 {
|
||||
compatible = "nxp,kinetis-pit";
|
||||
reg = <0x40037000 0x1000>;
|
||||
clocks = <&sim KINETIS_SIM_BUS_CLK 0x103c 23>;
|
||||
interrupts = <48 0>, <49 0>, <50 0>, <51 0>;
|
||||
status = "disabled";
|
||||
pit-channel = <0>;
|
||||
pit-period = <1000000>;
|
||||
clock-frequency = <60000000>;
|
||||
label = "PIT0";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nvic {
|
||||
arm,num-irq-priority-bits = <4>;
|
||||
};
|
||||
@@ -0,0 +1,38 @@
|
||||
/*
|
||||
* Copyright (c) 2019, Linaro
|
||||
*
|
||||
* SPDX-License-Identifier: Apache-2.0
|
||||
*/
|
||||
|
||||
#include <nxp/nxp_rt.dtsi>
|
||||
|
||||
/* i.MX rt1060 has two continuous on-chip RAM, one is part of the
|
||||
* FlexRAM mapped at 0x20280000 (vs 0x20280000 on rt1050) and is
|
||||
* configurable (256KB by defaults), the other one is dedicated 512KB
|
||||
* ram (OCRAM2) mapped at 0x20200000. In order to have a continuous
|
||||
* region, we describe them in one 768Kb unique node.
|
||||
*/
|
||||
&ocram {
|
||||
compatible = "mmio-sram";
|
||||
reg = <0x20200000 DT_SIZE_K(768)>;
|
||||
};
|
||||
|
||||
/* i.MX rt1060 has a second Ethernet controller. */
|
||||
/ {
|
||||
soc {
|
||||
enet2: ethernet@402d4000 {
|
||||
compatible = "nxp,kinetis-ethernet";
|
||||
reg = <0x402D4000 0x628>;
|
||||
interrupts = <152 0>;
|
||||
interrupt-names = "COMMON";
|
||||
status = "disabled";
|
||||
label = "ETH_1";
|
||||
ptp {
|
||||
compatible = "nxp,kinetis-ptp";
|
||||
status = "disabled";
|
||||
interrupts = <153 0>;
|
||||
interrupt-names = "IEEE1588_TMR";
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
@@ -0,0 +1,23 @@
|
||||
/*
|
||||
* Copyright (c) 2019, Linaro
|
||||
*
|
||||
* SPDX-License-Identifier: Apache-2.0
|
||||
*/
|
||||
|
||||
#include <nxp/nxp_rt1060.dtsi>
|
||||
|
||||
&flexspi2 {
|
||||
reg = <0x402a4000 0x4000>, <0x70000000 DT_SIZE_M(4)>;
|
||||
/* WINBOND */
|
||||
w25q32jvwj0: w25q32jvwj@0 {
|
||||
compatible = "nxp,imx-flexspi-nor";
|
||||
size = <33554432>;
|
||||
label = "W25Q32JVWJ0";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <133000000>;
|
||||
status = "okay";
|
||||
jedec-id = [ef 40 16];
|
||||
erase-block-size = <4096>;
|
||||
write-block-size = <1>;
|
||||
};
|
||||
};
|
||||
@@ -0,0 +1,87 @@
|
||||
/*
|
||||
* Copyright (c) 2021, NXP
|
||||
*
|
||||
* SPDX-License-Identifier: Apache-2.0
|
||||
*/
|
||||
|
||||
#include <nxp/nxp_rt11xx.dtsi>
|
||||
|
||||
/ {
|
||||
cpus {
|
||||
/delete-node/ cpu@0;
|
||||
};
|
||||
|
||||
/*
|
||||
* SRAM0 & SRAM1 are available only to the M4 core. EDMA_LPSR interrupts are connected
|
||||
* to the M4 core alone, hence this EDMA controller has been designated M4 only.
|
||||
* GPIO's 9, 11 are available to both M4 and M7 cores, however the GPIO interrupts are
|
||||
* only accesssible to the M4.
|
||||
*
|
||||
* Refer to Chapter 3 of the Reference Manual
|
||||
*/
|
||||
soc {
|
||||
sram0: memory@1ffe0000 {
|
||||
compatible = "mmio-sram";
|
||||
reg = <0x1ffe0000 DT_SIZE_K(128)>;
|
||||
};
|
||||
|
||||
sram1: memory@20000000 {
|
||||
compatible = "mmio-sram";
|
||||
reg = <0x20000000 DT_SIZE_K(128)>;
|
||||
};
|
||||
|
||||
/*
|
||||
* M4 uses different addresses from the M7 core for GPIO2 and
|
||||
* GPIO3, see pg. 1364 of RT1160 ref manual for example
|
||||
*/
|
||||
gpio2: gpio@40130000 {
|
||||
compatible = "nxp,imx-gpio";
|
||||
reg = <0x40130000 0x4000>;
|
||||
interrupts = <102 0>, <103 0>;
|
||||
label = "GPIO_2";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
};
|
||||
|
||||
gpio3: gpio@40134000 {
|
||||
compatible = "nxp,imx-gpio";
|
||||
reg = <0x40134000 0x4000>;
|
||||
interrupts = <104 0>, <105 0>;
|
||||
label = "GPIO_3";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
};
|
||||
|
||||
edma_lpsr0: dma-controller@40c14000 {
|
||||
#dma-cells = <2>;
|
||||
compatible = "nxp,mcux-edma";
|
||||
dma-channels = <32>;
|
||||
dma-requests = <208>;
|
||||
nxp,mem2mem;
|
||||
nxp,a_on;
|
||||
reg = <0x40c14000 0x4000>,
|
||||
<0x40c18000 0x4000>;
|
||||
clocks = <&ccm IMX_CCM_EDMA_LPSR_CLK 0x7C 0x000000C0>;
|
||||
status = "disabled";
|
||||
label = "DMA_0";
|
||||
interrupts = <0 0>, <1 0>, <2 0>, <3 0>,
|
||||
<4 0>, <5 0>, <6 0>, <7 0>,
|
||||
<8 0>, <9 0>, <10 0>, <11 0>,
|
||||
<12 0>, <13 0>, <14 0>, <15 0>,
|
||||
<16 0>;
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
|
||||
&gpio9 {
|
||||
interrupts = <99 0>;
|
||||
};
|
||||
|
||||
&gpio11 {
|
||||
/* GPIO 7-11 share the same interrupt on the CM4 */
|
||||
interrupts = <99 0>;
|
||||
status = "disabled";
|
||||
};
|
||||
@@ -0,0 +1,85 @@
|
||||
/*
|
||||
* Copyright (c) 2021, NXP
|
||||
*
|
||||
* SPDX-License-Identifier: Apache-2.0
|
||||
*/
|
||||
|
||||
#include <nxp/nxp_rt11xx.dtsi>
|
||||
|
||||
/ {
|
||||
cpus {
|
||||
/delete-node/ cpu@1;
|
||||
};
|
||||
/*
|
||||
* ITCM & DTCM are available only to the M7 core. EDMA interrupts are connected
|
||||
* to the M7 core alone, hence this EDMA controller has been designated M7 only.
|
||||
* GPIO 6 is available to both M4 and M7 cores, however the GPIO interrupt is
|
||||
* only accesssible to the M7.
|
||||
*
|
||||
* Refer to Chapter 3 of the Reference Manual
|
||||
*/
|
||||
soc {
|
||||
flexram: flexram@40028000 {
|
||||
reg = <0x40028000 0x4000>;
|
||||
interrupts = <50 0>;
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
itcm: itcm@0 {
|
||||
compatible = "nxp,imx-itcm";
|
||||
reg = <0x00000000 DT_SIZE_K(256)>;
|
||||
};
|
||||
|
||||
dtcm: dtcm@20000000 {
|
||||
compatible = "nxp,imx-dtcm";
|
||||
reg = <0x20000000 DT_SIZE_K(256)>;
|
||||
};
|
||||
};
|
||||
|
||||
/*
|
||||
* M7 uses different addresses from the M4 core for GPIO2 and
|
||||
* GPIO3, see pg. 1460 of RT1160 ref manual for example
|
||||
*/
|
||||
gpio2: gpio@42008000 {
|
||||
compatible = "nxp,imx-gpio";
|
||||
reg = <0x42008000 0x4000>;
|
||||
interrupts = <102 0>, <103 0>;
|
||||
label = "GPIO_2";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
};
|
||||
|
||||
gpio3: gpio@4200c000 {
|
||||
compatible = "nxp,imx-gpio";
|
||||
reg = <0x4200c000 0x4000>;
|
||||
interrupts = <104 0>, <105 0>;
|
||||
label = "GPIO_3";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
};
|
||||
|
||||
edma0: dma-controller@40070000 {
|
||||
#dma-cells = <2>;
|
||||
compatible = "nxp,mcux-edma";
|
||||
dma-channels = <32>;
|
||||
dma-requests = <208>;
|
||||
nxp,mem2mem;
|
||||
nxp,a_on;
|
||||
reg = <0x40070000 0x4000>,
|
||||
<0x40074000 0x4000>;
|
||||
clocks = <&ccm IMX_CCM_EDMA_CLK 0x7C 0x000000C0>;
|
||||
status = "disabled";
|
||||
label = "DMA_0";
|
||||
interrupts = <0 0>, <1 0>, <2 0>, <3 0>,
|
||||
<4 0>, <5 0>, <6 0>, <7 0>,
|
||||
<8 0>, <9 0>, <10 0>, <11 0>,
|
||||
<12 0>, <13 0>, <14 0>, <15 0>,
|
||||
<16 0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gpio6 {
|
||||
interrupts = <61 0>, <62 0>;
|
||||
};
|
||||
@@ -0,0 +1,85 @@
|
||||
/*
|
||||
* Copyright (c) 2021, NXP
|
||||
*
|
||||
* SPDX-License-Identifier: Apache-2.0
|
||||
*/
|
||||
|
||||
#include <nxp/nxp_rt11xx.dtsi>
|
||||
|
||||
/ {
|
||||
cpus {
|
||||
/delete-node/ cpu@0;
|
||||
};
|
||||
|
||||
/*
|
||||
* SRAM0 & SRAM1 are available only to the M4 core. EDMA_LPSR interrupts are connected
|
||||
* to the M4 core alone, hence this EDMA controller has been designated M4 only.
|
||||
* GPIO's 9, 11 are available to both M4 and M7 cores, however the GPIO interrupts are
|
||||
* only accesssible to the M4.
|
||||
*
|
||||
* Refer to Chapter 3 of the Reference Manual
|
||||
*/
|
||||
soc {
|
||||
sram0: memory@1ffe0000 {
|
||||
compatible = "mmio-sram";
|
||||
reg = <0x1ffe0000 DT_SIZE_K(128)>;
|
||||
};
|
||||
|
||||
sram1: memory@20000000 {
|
||||
compatible = "mmio-sram";
|
||||
reg = <0x20000000 DT_SIZE_K(128)>;
|
||||
zephyr,memory-region = "SRAM1";
|
||||
};
|
||||
|
||||
/*
|
||||
* M4 uses different addresses from the M7 core for GPIO2 and
|
||||
* GPIO3, see pg. 1410 of RT1170 ref manual for example
|
||||
*/
|
||||
gpio2: gpio@40130000 {
|
||||
compatible = "nxp,imx-gpio";
|
||||
reg = <0x40130000 0x4000>;
|
||||
interrupts = <102 0>, <103 0>;
|
||||
label = "GPIO_2";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
};
|
||||
|
||||
gpio3: gpio@40134000 {
|
||||
compatible = "nxp,imx-gpio";
|
||||
reg = <0x40134000 0x4000>;
|
||||
interrupts = <104 0>, <105 0>;
|
||||
label = "GPIO_3";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
};
|
||||
|
||||
edma_lpsr0: dma-controller@40c14000 {
|
||||
#dma-cells = <2>;
|
||||
compatible = "nxp,mcux-edma";
|
||||
dma-channels = <32>;
|
||||
dma-requests = <208>;
|
||||
nxp,mem2mem;
|
||||
nxp,a_on;
|
||||
reg = <0x40c14000 0x4000>,
|
||||
<0x40c18000 0x4000>;
|
||||
clocks = <&ccm IMX_CCM_EDMA_LPSR_CLK 0x7C 0x000000C0>;
|
||||
status = "disabled";
|
||||
label = "DMA_0";
|
||||
interrupts = <0 0>, <1 0>, <2 0>, <3 0>,
|
||||
<4 0>, <5 0>, <6 0>, <7 0>,
|
||||
<8 0>, <9 0>, <10 0>, <11 0>,
|
||||
<12 0>, <13 0>, <14 0>, <15 0>,
|
||||
<16 0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gpio9 {
|
||||
interrupts = <99 0>;
|
||||
};
|
||||
|
||||
&gpio11 {
|
||||
/* GPIO 7-11 share the same interrupt on the CM4 */
|
||||
interrupts = <99 0>;
|
||||
status = "disabled";
|
||||
};
|
||||
@@ -0,0 +1,87 @@
|
||||
/*
|
||||
* Copyright (c) 2021, NXP
|
||||
*
|
||||
* SPDX-License-Identifier: Apache-2.0
|
||||
*/
|
||||
|
||||
#include <nxp/nxp_rt11xx.dtsi>
|
||||
|
||||
/ {
|
||||
cpus {
|
||||
/delete-node/ cpu@1;
|
||||
};
|
||||
/*
|
||||
* ITCM & DTCM are available only to the M7 core. EDMA interrupts are connected
|
||||
* to the M7 core alone, hence this EDMA controller has been designated M7 only.
|
||||
* GPIO 6 is available to both M4 and M7 cores, however the GPIO interrupt is
|
||||
* only accesssible to the M7.
|
||||
*
|
||||
* Refer to Chapter 3 of the Reference Manual
|
||||
*/
|
||||
soc {
|
||||
flexram: flexram@40028000 {
|
||||
reg = <0x40028000 0x4000>;
|
||||
interrupts = <50 0>;
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
itcm: itcm@0 {
|
||||
compatible = "nxp,imx-itcm";
|
||||
reg = <0x00000000 DT_SIZE_K(256)>;
|
||||
zephyr,memory-region = "ITCM";
|
||||
};
|
||||
|
||||
dtcm: dtcm@20000000 {
|
||||
compatible = "nxp,imx-dtcm";
|
||||
reg = <0x20000000 DT_SIZE_K(256)>;
|
||||
zephyr,memory-region = "DTCM";
|
||||
};
|
||||
};
|
||||
|
||||
/*
|
||||
* M7 uses different addresses from the M4 core for GPIO2 and
|
||||
* GPIO3, see pg. 1460 of RT1170 ref manual for example
|
||||
*/
|
||||
gpio2: gpio@42008000 {
|
||||
compatible = "nxp,imx-gpio";
|
||||
reg = <0x42008000 0x4000>;
|
||||
interrupts = <102 0>, <103 0>;
|
||||
label = "GPIO_2";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
};
|
||||
|
||||
gpio3: gpio@4200c000 {
|
||||
compatible = "nxp,imx-gpio";
|
||||
reg = <0x4200c000 0x4000>;
|
||||
interrupts = <104 0>, <105 0>;
|
||||
label = "GPIO_3";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
};
|
||||
|
||||
edma0: dma-controller@40070000 {
|
||||
#dma-cells = <2>;
|
||||
compatible = "nxp,mcux-edma";
|
||||
dma-channels = <32>;
|
||||
dma-requests = <208>;
|
||||
nxp,mem2mem;
|
||||
nxp,a_on;
|
||||
reg = <0x40070000 0x4000>,
|
||||
<0x40074000 0x4000>;
|
||||
clocks = <&ccm IMX_CCM_EDMA_CLK 0x7C 0x000000C0>;
|
||||
status = "disabled";
|
||||
label = "DMA_0";
|
||||
interrupts = <0 0>, <1 0>, <2 0>, <3 0>,
|
||||
<4 0>, <5 0>, <6 0>, <7 0>,
|
||||
<8 0>, <9 0>, <10 0>, <11 0>,
|
||||
<12 0>, <13 0>, <14 0>, <15 0>,
|
||||
<16 0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gpio6 {
|
||||
interrupts = <61 0>, <62 0>;
|
||||
};
|
||||
Reference in New Issue
Block a user