mirror of
https://gitee.com/mirrors_PX4/PX4-Autopilot.git
synced 2026-04-14 10:07:39 +08:00
194 lines
8.6 KiB
Markdown
194 lines
8.6 KiB
Markdown
# DShot ESCs
|
||
|
||
DShot is an alternative ESC protocol that has several advantages over [PWM](../peripherals/pwm_escs_and_servo.md) or [OneShot](../peripherals/oneshot.md):
|
||
|
||
- Зменшений час затримки.
|
||
- Підвищена надійність за допомогою контрольної суми.
|
||
- Не потрібна калібрування ESC, оскільки протокол використовує цифрове кодування.
|
||
- Зворотний зв'язок телеметрії доступний/підтримується на деяких ESC.
|
||
- Може змінювати напрямок обертання двигуна за допомогою команд при потребі (замість фізичного переміщення проводів / перепайки).
|
||
- Інші корисні команди підтримуються.
|
||
|
||
Ця тема показує, як підключити та налаштувати DShot ESC.
|
||
|
||
## Supported ESC
|
||
|
||
[ESCs & Motors > Supported ESCs](../peripherals/esc_motors#supported-esc) has a list of supported ESC (check "Protocols" column for DShot ESC).
|
||
|
||
## Wiring/Connections {#wiring}
|
||
|
||
DShot ESC are wired the same way as [PWM ESCs](pwm_escs_and_servo.md).
|
||
Єдина відмінність полягає в тому, що їх можна підключити лише до FMU, і зазвичай лише до певного підмножини контактів.
|
||
|
||
:::info
|
||
You may want to check the actuator configuration screen to see what pins are available for DShot on your controller before wiring up!
|
||
:::
|
||
|
||
Pixhawk controllers with both an FMU and an IO board usually label them as `AUX` (FMU) and `MAIN` (IO), respectively.
|
||
These match the `PWM AUX` and `PWM MAIN` output tabs on the actuator configuration screen.
|
||
For these controllers connect the DShot ESC to the `AUX` port.
|
||
|
||
Controllers that don't have an IO board usually label the (single) output port as `MAIN`, and this is where you will connect your DShot ESC.
|
||
If the controller without IO has its own firmware, the actuator assignment will be to the matching `PWM MAIN` outputs.
|
||
However if the same firmware is used for hardware with/without the IO board, such as for the Pixhawk 4 and Pixhawk 4 Mini, then actuator assignment tab used is the same in both cases: `PWM AUX` (i.e. not matching the port label `MAIN` in the "mini" case).
|
||
|
||
## Налаштування
|
||
|
||
:::warning
|
||
Remove propellers before changing ESC configuration parameters!
|
||
:::
|
||
|
||
Enable DShot for your required outputs in the [Actuator Configuration](../config/actuators.md).
|
||
|
||
DShot comes with different speed options: _DShot150_, _DShot300_, and _DShot600_ where the number indicates the speed in kilo-bits/second.
|
||
Ви повинні встановити параметр на найвищу швидкість, підтримувану вашим ESC (згідно з його технічним описом).
|
||
|
||
Підключіть батарею та озбройте транспортний засіб.
|
||
РЕГБ повинні ініціалізуватися, а мотори повинні обертатися в правильних напрямках.
|
||
|
||
- If the motors do not spin in the correct direction (for the [selected airframe](../airframes/airframe_reference.md)) you can reverse them in the UI using the **Set Spin Direction** option (this option appears after you select DShot and assign motors).
|
||
You can also reverse motors by sending an [ESC Command](#commands).
|
||
|
||
## ESC Commands {#commands}
|
||
|
||
Commands can be sent to the ESC via the [MAVLink shell](../debug/mavlink_shell.md).
|
||
See [here](../modules/modules_driver.md#dshot) for a full reference of the supported commands.
|
||
|
||
Найважливіші з них:
|
||
|
||
- Make a motor connected to to FMU output pin 1 beep (helps with identifying motors)
|
||
|
||
```sh
|
||
dshot beep1 -m 1
|
||
```
|
||
|
||
- Retrieve ESC information (requires telemetry, see below):
|
||
|
||
```sh
|
||
nsh> dshot esc_info -m 2
|
||
INFO [dshot] ESC Type: #TEKKO32_4in1#
|
||
INFO [dshot] MCU Serial Number: xxxxxx-xxxxxx-xxxxxx-xxxxxx
|
||
INFO [dshot] Firmware version: 32.60
|
||
INFO [dshot] Rotation Direction: normal
|
||
INFO [dshot] 3D Mode: off
|
||
INFO [dshot] Low voltage Limit: off
|
||
INFO [dshot] Current Limit: off
|
||
INFO [dshot] LED 0: unsupported
|
||
INFO [dshot] LED 1: unsupported
|
||
INFO [dshot] LED 2: unsupported
|
||
INFO [dshot] LED 3: unsupported
|
||
```
|
||
|
||
- Permanently set the spin direction of a motor connected to FMU output pin 1 (while motors are _not_ spinning):
|
||
|
||
- Set spin direction to `reversed`:
|
||
|
||
```sh
|
||
dshot reverse -m 1
|
||
dshot save -m 1
|
||
```
|
||
|
||
Retrieving ESC information will then show:
|
||
|
||
```sh
|
||
Rotation Direction: reversed
|
||
```
|
||
|
||
- Set spin direction to `normal`:
|
||
|
||
```sh
|
||
dshot normal -m 1
|
||
dshot save -m 1
|
||
```
|
||
|
||
Retrieving ESC information will then show:
|
||
|
||
```sh
|
||
Rotation Direction: normal
|
||
```
|
||
|
||
:::info
|
||
|
||
- The commands will have no effect if the motors are spinning, or if the ESC is already set to the corresponding direction.
|
||
- The ESC will revert to its last saved direction (normal or reversed) on reboot if `save` is not called after changing the direction.
|
||
|
||
|
||
:::
|
||
|
||
## ESC Telemetry
|
||
|
||
Some ESCs are capable of sending telemetry back to the flight controller through a UART RX port.
|
||
Ці DShot ESCs матимуть додатковий телеметрійний дріт.
|
||
|
||
The provided telemetry includes:
|
||
|
||
- Температура
|
||
- Напруга
|
||
- Current
|
||
- Accumulated current consumption
|
||
- Значення RPM
|
||
|
||
Щоб увімкнути цю функцію (на ESC, які її підтримують):
|
||
|
||
1. Об'єднайте всі дроти телеметрії з усіх ESC разом, а потім підключіть їх до одного з контактів RX на не використаному порту послідовного зв'язку контролера польоту.
|
||
2. Enable telemetry on that serial port using [DSHOT_TEL_CFG](../advanced_config/parameter_reference.md#DSHOT_TEL_CFG).
|
||
|
||
Після перезавантаження ви можете перевірити, чи працює телеметрія (переконайтеся, що акумулятор підключений), використовуючи:
|
||
|
||
```sh
|
||
dshot esc_info -m 1
|
||
```
|
||
|
||
:::tip
|
||
You may have to configure [MOT_POLE_COUNT](../advanced_config/parameter_reference.md#MOT_POLE_COUNT) to get the correct RPM values.
|
||
:::
|
||
|
||
:::tip
|
||
Not all DSHOT-capable ESCs support `[esc_info]`(e.g. APD 80F3x), even when telemetry is supported and enabled.
|
||
Отримана помилка:
|
||
|
||
```sh
|
||
ERROR [dshot] No data received. If telemetry is setup correctly, try again.
|
||
```
|
||
|
||
Перевірте документацію виробника для підтвердження/подробиць.
|
||
:::
|
||
|
||
## Bidirectional DShot (Telemetry)
|
||
|
||
<Badge type="tip" text="PX4 v1.16" />
|
||
|
||
Bidirectional DShot is a protocol that can provide telemetry including: high rate ESC RPM data, voltage, current, and temperature with a single wire.
|
||
|
||
The PX4 implementation currently enables only ESC RPM (eRPM) data collection from each ESC at high frequencies.
|
||
This telemetry significantly improves the performance of [Dynamic Notch Filters](../config_mc/filter_tuning.md#dynamic-notch-filters) and enables more precise vehicle tuning.
|
||
|
||
:::info
|
||
The [ESC Telemetry](#esc-telemetry) described above is currently still necessary if you want voltage, current, or temperature information.
|
||
It's setup and use is independent of bidirectional DShot.
|
||
:::
|
||
|
||
### Налаштування програмного забезпечення
|
||
|
||
The ESC must be connected to FMU outputs only.
|
||
These will be labeled `MAIN` on flight controllers that only have one PWM bus, and `AUX` on controllers that have both `MAIN` and `AUX` ports (i.e. FCs that have an IO board).
|
||
|
||
:::warning
|
||
**Limited hardware support**
|
||
This feature is only supported on flight controllers with the following processors:
|
||
|
||
- STM32H7: First four FMU outputs
|
||
- Must be connected to the first 4 FMU outputs, and these outputs must also be mapped to the same timer.
|
||
- [KakuteH7](../flight_controller/kakuteh7v2.md) is not supported because the outputs are not mapped to the same timer.
|
||
- [i.MXRT](../flight_controller/nxp_mr_vmu_rt1176.md) (V6X-RT & Tropic): 8 FMU outputs.
|
||
|
||
No other boards are supported.
|
||
:::
|
||
|
||
### Configuration {#bidirectional-dshot-configuration}
|
||
|
||
To enable bidirectional DShot, set the [DSHOT_BIDIR_EN](../advanced_config/parameter_reference.md#DSHOT_BIDIR_EN) parameter.
|
||
|
||
The system calculates actual motor RPM from the received eRPM data using the [MOT_POLE_COUNT](../advanced_config/parameter_reference.md#MOT_POLE_COUNT) parameter.
|
||
This parameter must be set correctly for accurate RPM reporting.
|