mirror of
https://gitee.com/mirrors_PX4/PX4-Autopilot.git
synced 2026-04-14 10:07:39 +08:00
82 lines
5.0 KiB
Markdown
82 lines
5.0 KiB
Markdown
# Системна консоль PX4
|
||
|
||
The PX4 _System Console_ provides low-level access to the system, debug output and analysis of the system boot process.
|
||
|
||
:::tip
|
||
The console should be used for debugging if the system won't boot.
|
||
The [MAVLink Shell](../debug/mavlink_shell.md) may otherwise be more suitable, as it is much easier to set up and can be used for [many of the same tasks](../debug/consoles.md#console_vs_shell).
|
||
:::
|
||
|
||
## Підключення консолі
|
||
|
||
The console is made available through a (board-specific) UART that can be connected to a computer USB port using a [3.3V FTDI](https://www.digikey.com/en/products/detail/TTL-232R-3V3/768-1015-ND/1836393) cable.
|
||
Це дозволяє доступ до консолі за допомогою термінальної програми.
|
||
|
||
Pixhawk controller manufacturers are expected to expose the console UART and SWD (JTAG) debug interfaces through a dedicated _debug port_ that complies with the [Pixhawk Connector Standard](#pixhawk_debug_port).
|
||
На жаль, деякі дошки попередні цьому стандарту або не відповідають йому.
|
||
|
||
:::info
|
||
Developers targeting a number of different boards may wish to use a [debug adapter](../debug/swd_debug.md#debug-adapters) to simplify connecting boards to FTDI cables and [debug probes](../debug/swd_debug.md#debug-probes-for-px4-hardware).
|
||
:::
|
||
|
||
Розділи нижче наводять посилання на інформацію про проводку та консоль системи для багатьох загальних дошок.
|
||
|
||
### Проводка, специфічна для плати
|
||
|
||
The System Console UART pinouts/debug ports are typically documented in [autopilot overview pages](../flight_controller/index.md) (some are linked below):
|
||
|
||
- [3DR Pixhawk v1 Flight Controller](../flight_controller/pixhawk.md#console-port) (also applies to
|
||
[mRo Pixhawk](../flight_controller/mro_pixhawk.md#debug-ports), [Holybro pix32](../flight_controller/holybro_pix32.md#debug-port))
|
||
- [Pixhawk 3](../flight_controller/pixhawk3_pro.md#debug-port)
|
||
- [Pixracer](../flight_controller/pixracer.md#debug-port)
|
||
|
||
<a id="pixhawk_debug_port"></a>
|
||
|
||
### Порти відладки Pixhawk
|
||
|
||
Pixhawk flight controllers usually come with a [Pixhawk Connector Standard Debug Port](../debug/swd_debug.md#pixhawk-connector-standard-debug-ports) which will be either the 10 pin [Pixhawk Debug Full](../debug/swd_debug.md#pixhawk-debug-full) or 6 pin [Pixhawk Debug Mini](../debug/swd_debug.md#pixhawk-debug-mini) port.
|
||
|
||
Ці порти мають контакти для консольного TX та RX, які можуть бути підключені до кабелю FTDI.
|
||
The mapping for the [Pixhawk Debug Mini](../debug/swd_debug.md#pixhawk-debug-mini) to FTDI is shown below.
|
||
|
||
| Порти відладки Pixhawk | - | FTDI | - |
|
||
| -------------------------- | ----------------------------------- | ---- | ------------------------------------------------------------------- |
|
||
| 1 (red) | TARGET PROCESSOR VOLTAGE | | N/C (використовується для налагодження SWD/JTAG) |
|
||
| 2 (blk) | CONSOLE TX (OUT) | 5 | FTDI RX (yellow) |
|
||
| 3 (blk) | CONSOLE RX (IN) | 4 | FTDI TX (orange) |
|
||
| 4 (blk) | SWDIO | | N/C (використовується для налагодження SWD/JTAG) |
|
||
| 5 (blk) | SWCLK | | N/C (використовується для налагодження SWD/JTAG) |
|
||
| 6 (blk) | GND | 1 | FTDI GND (black) |
|
||
|
||
The [SWD Debug Port](../debug/swd_debug.md) page and individual flight controller pages have more information about debug port pinouts.
|
||
|
||
## Відкриття консолі
|
||
|
||
Після підключення консолі використовуйте інструмент вибору або типові порти з'єднання, описані нижче:
|
||
|
||
### Linux / Mac OS: Screen
|
||
|
||
Встановіть screen на Ubuntu (Mac OS вже має його встановленим):
|
||
|
||
```sh
|
||
sudo apt-get install screen
|
||
```
|
||
|
||
- Серійний підключення: Pixhawk v1 / Pixracer використовує швидкість передачі 57600 бод
|
||
|
||
Connect screen at BAUDRATE baud, 8 data bits, 1 stop bit to the right serial port (use `ls /dev/tty*` and watch what changes when unplugging / replugging the USB device). Common names are `/dev/ttyUSB0` and `/dev/ttyACM0` for Linux and `/dev/tty.usbserial-ABCBD` for Mac OS.
|
||
|
||
```sh
|
||
screen /dev/ttyXXX BAUDRATE 8N1
|
||
```
|
||
|
||
### Windows: PuTTY
|
||
|
||
Download [PuTTY](https://www.chiark.greenend.org.uk/~sgtatham/putty/latest.html) and start it.
|
||
|
||
Потім виберіть 'серійне підключення' і встановіть параметри порту:
|
||
|
||
- 57600 baud
|
||
- 8 data bits
|
||
- 1 stop bit
|