mirror of
https://gitee.com/mirrors_PX4/PX4-Autopilot.git
synced 2026-04-14 10:07:39 +08:00
89 lines
2.8 KiB
Markdown
89 lines
2.8 KiB
Markdown
# CUAV Pixhack V3 (Discontinued)
|
|
|
|
<Badge type="info" text="Discontinued" />
|
|
|
|
:::warning
|
|
This flight controller has been [discontinued](../flight_controller/autopilot_experimental.md) and is no longer commercially available.
|
|
:::
|
|
|
|
:::warning
|
|
PX4 does not manufacture this (or any) autopilot.
|
|
Contact the [manufacturer](https://store.cuav.net/) for hardware support or compliance issues.
|
|
:::
|
|
|
|
The CUAV _Pixhack V3_ flight controller board is a flexible autopilot intended primarily for manufacturers of commercial systems.
|
|
|
|
The board is a variant of the SOLO Pixhawk<sup>®</sup> 2 (PH2) flight controller, which is in turn based on the [Pixhawk-project](https://pixhawk.org/) **FMUv3** open hardware design.
|
|
It runs PX4 on the [NuttX](https://nuttx.apache.org/) OS, and is fully compatible with both PX4 or ArduPilot<sup>®</sup> (APM) firmware.
|
|
|
|
_Pixhack V3_ has significant improvements with respect to the original design, including better interface layout and the addition of vibration damping and a thermostat system.
|
|
|
|
|
|
|
|
::: info
|
|
This flight controller is [manufacturer supported](../flight_controller/autopilot_manufacturer_supported.md).
|
|
:::
|
|
|
|
## Quick Summary
|
|
|
|
- Microprocessor:
|
|
- STM32F427
|
|
- STM32F100 (Failsafe co-processor)
|
|
- Sensors:
|
|
- Accelerometers (3): LS303D, MPU6000, MPU9250/hmc5983
|
|
- Gyroscopes (3): L3GD20, MPU6000, MPU9250
|
|
- Compass (2): LS303D, MPU9250
|
|
- Barometer (2): MS5611 X2
|
|
- Interfaces:
|
|
- MAVLink UART (2)
|
|
- GPS UART (2)
|
|
- DEBUG UART (1)
|
|
- RC IN (for PPM, SBUS, DSM/DSM2)
|
|
- RSSI IN: PWM OR 3.3ADC
|
|
- I2C (2)
|
|
- CAN BUS (1)
|
|
- ADC IN: 3.3V X1 , 6.6V X1
|
|
- PWM OUT: 8 PWM IO + 4 IO
|
|
- Power System:
|
|
- PM POWER IN: 4.5 ~ 5.5 V
|
|
- USB POWER IN: 5.0 V +- 0.25v
|
|
- Weight and Dimensions:
|
|
- Weight: 63g
|
|
- Width: 68mm
|
|
- Thickness: 17mm
|
|
- Length: 44mm
|
|
- Other Characteristics:
|
|
- Operating temperature: -20 ~ 60°C
|
|
|
|
## Availability
|
|
|
|
The board can be purchased from:
|
|
|
|
- [leixun.aliexpress.com/store](https://leixun.aliexpress.com/store)
|
|
|
|
## Building Firmware
|
|
|
|
:::tip
|
|
Most users will not need to build this firmware!
|
|
It is pre-built and automatically installed by _QGroundControl_ when appropriate hardware is connected.
|
|
:::
|
|
|
|
To [build PX4](../dev_setup/building_px4.md) for this target:
|
|
|
|
```sh
|
|
make px4_fmu-v3_default
|
|
```
|
|
|
|
<!-- Pinouts and Schematics: section removed as guides no longer published -->
|
|
|
|
## Serial Port Mapping
|
|
|
|
| UART | Device | Port |
|
|
| ------ | ---------- | --------------------- |
|
|
| UART1 | /dev/ttyS0 | IO debug |
|
|
| USART2 | /dev/ttyS1 | TELEM1 (flow control) |
|
|
| USART3 | /dev/ttyS2 | TELEM2 (flow control) |
|
|
| UART4 | | |
|
|
| UART7 | | CONSOLE |
|
|
| UART8 | | SERIAL4 |
|