mirror of
https://gitee.com/mirrors_PX4/PX4-Autopilot.git
synced 2026-10-17 17:43:35 +08:00
163 lines
6.9 KiB
Markdown
163 lines
6.9 KiB
Markdown
# RaccoonLab FMUv6X Autopilot
|
|
|
|
:::warning
|
|
PX4 does not manufacture this (or any) autopilot.
|
|
Contact the [manufacturer](https://raccoonlab.co) for hardware support or compliance issues.
|
|
:::
|
|
|
|
The [RaccoonLab FMUv6X](https://docs.raccoonlab.co/guide/autopilot/RCLv6X.html) flight controller is based on the following Pixhawk® standards: [Pixhawk Autopilot FMUv6X Standard](https://github.com/pixhawk/Pixhawk-Standards/blob/master/DS-012%20Pixhawk%20Autopilot%20v6X%20Standard.pdf), [Autopilot Bus Standard](https://github.com/pixhawk/Pixhawk-Standards/blob/master/DS-010%20Pixhawk%20Autopilot%20Bus%20Standard.pdf), and [Connector Standard](https://github.com/pixhawk/Pixhawk-Standards/blob/master/DS-009%20Pixhawk%20Connector%20Standard.pdf).
|
|
|
|
Equipped with a high-performance H7 Processor, modular design, triple redundancy, temperature-controlled IMU board, and isolated sensor domains, it delivers exceptional performance, reliability, and flexibility.
|
|
At RaccoonLab, we focus on DroneCAN and Cyphal-based onboard control system buses.
|
|
Our autopilot is part of a larger DroneCAN and Cyphal ecosystem, making it an ideal choice for next-generation intelligent vehicles.
|
|
|
|
|
|
|
|
RaccoonLab offers versatile HATs for both Raspberry Pi and NVIDIA Jetson Xavier NX, enhancing connectivity and functionality.
|
|
The [Jetson Xavier NX HAT](https://docs.raccoonlab.co/guide/nx_hat/) is designed to integrate the CAN bus with the Jetson Xavier NX, enabling access to Cyphal and DroneCAN protocols.
|
|
The [Raspberry Pi CM4 HAT](https://docs.raccoonlab.co/guide/rpi_hat/) provides robust features, including CAN bus connectivity, an LTE modem, internal voltage measurement, SWD debugging for other MCUs, and UART communication with PX4 over MAVLINK.
|
|
These HATs expand the capabilities of devices, making them ideal for advanced robotics and UAV applications.
|
|
|
|
:::tip
|
|
This autopilot is [supported](../flight_controller/autopilot_pixhawk_standard.md) by the PX4 maintenance and test teams.
|
|
:::
|
|
|
|
## Key Design Points
|
|
|
|
- High performance STM32H753 Processor
|
|
- Modular flight controller: separated IMU, FMU, and Base system connected by a 100-pin & a 50-pin Pixhawk Autopilot Bus connector.
|
|
- Redundancy: 3x IMU sensors & 2x Barometer sensors on separate buses
|
|
- Triple redundancy domains: Completely isolated sensor domains with separate buses and separate power control
|
|
- Newly designed vibration isolation system to filter out high frequency vibration and reduce noise to ensure accurate readings
|
|
- Ethernet interface for high-speed mission computer integration
|
|
|
|
## Processors & Sensors
|
|
|
|
- FMU Processor: STM32H753
|
|
- 32 Bit Arm Cortex-M7, 480MHz, 2MB flash memory, 1MB RAM
|
|
- IO 프로세서: STM32F100
|
|
- 32 Bit Arm Cortex-M3, 24MHz, 8KB SRAM
|
|
- 내장 센서 :
|
|
- Accel/Gyro: ICM-20649 or BMI088
|
|
- Accel/Gyro: ICM-42688-P
|
|
- Accel/Gyro: ICM-42670-P
|
|
- Mag: BMM150
|
|
- Barometer: 2x BMP388
|
|
|
|
## Electrical data
|
|
|
|
- Voltage Ratings:
|
|
- Max input voltage: 36V
|
|
- USB Power Input: 4.75\~5.25V
|
|
- Servo Rail Input: 0\~36V
|
|
- Current Ratings:
|
|
- `TELEM1` output current limiter: 1.5A
|
|
- All other port combined output current limiter: 1.5A
|
|
|
|
## Mechanical data
|
|
|
|
- 크기
|
|
- Flight Controller Module: 38.8 x 31.8 x 14.6mm
|
|
- Standard Baseboard: 52.4 x 103.4 x 16.7mm
|
|
- Mini Baseboard: 43.4 x 72.8 x 14.2 mm
|
|
- 중량
|
|
- Flight Controller Module: 23g
|
|
- Standard Baseboard: 51g
|
|
- Mini Baseboard: 26.5g
|
|
|
|
3D model can be downloaded on [GrabCAD](https://grabcad.com/library/raccoonlab-autopilot-1).
|
|
|
|
|
|
|
|
## 인터페이스
|
|
|
|
- 16- PWM servo outputs
|
|
- R/C input for Spektrum / DSM
|
|
- Dedicated R/C input for PPM and S.Bus input
|
|
- Dedicated analog / PWM RSSI input and S.Bus output
|
|
- 범용 시리얼 포트 4개
|
|
- 전체 흐름 제어 3개
|
|
- 1 with separate 1.5A current limit (`TELEM1`)
|
|
- 1 with I2C and additional GPIO line for external NFC reader
|
|
- 2 GPS ports
|
|
- 1 full GPS plus Safety Switch Port
|
|
- 1 basic GPS port
|
|
- 1 I2C port
|
|
- 1 Ethernet port
|
|
- Transformerless Applications
|
|
- 100Mbps
|
|
- 1 SPI bus
|
|
- 2 chip select lines
|
|
- 2 data-ready lines
|
|
- 1 SPI SYNC line
|
|
- 1 SPI reset line
|
|
- 2 CAN Buses for CAN peripheral
|
|
- CAN Bus has individual silent controls or ESC RX-MUX control
|
|
- 2 Power input ports with SMBus
|
|
- 1 AD & IO port
|
|
- 2개의 추가 아날로그 입력
|
|
- 1 PWM/Capture input
|
|
- 2 Dedicated debug and GPIO lines
|
|
|
|
## 시리얼 포트 매핑
|
|
|
|
| UART | 장치 | 포트 |
|
|
| ------ | ---------- | ------------------------------- |
|
|
| USART1 | /dev/ttyS0 | GPS |
|
|
| USART2 | /dev/ttyS1 | TELEM3 |
|
|
| USART3 | /dev/ttyS2 | 디버그 콘솔 |
|
|
| UART4 | /dev/ttyS3 | UART4 & I2C |
|
|
| UART5 | /dev/ttyS4 | TELEM2 |
|
|
| USART6 | /dev/ttyS5 | PX4IO/RC |
|
|
| UART7 | /dev/ttyS6 | TELEM1 |
|
|
| UART8 | /dev/ttyS7 | GPS2 |
|
|
|
|
## 정격 전압
|
|
|
|
_RaccoonLab FMUv6X_ can be triple-redundant on the power supply if three power sources are supplied.
|
|
The three power rails are: **POWER1**, **POWER2** and **USB**.
|
|
The **POWER1** & **POWER2** ports on the RaccoonLab FMUv6X uses the 6 circuit [2.00mm Pitch CLIK-Mate Wire-to-Board PCB Receptacle](https://www.molex.com/en-us/products/part-detail/5024430670).
|
|
|
|
**Normal Operation Maximum Ratings**
|
|
|
|
이러한 조건에서 전원은 아래의 순서대로 시스템에 전원을 공급하여야합니다.
|
|
|
|
1. **POWER1** and **POWER2** inputs (4.9V to 5.5V)
|
|
2. **USB** input (4.75V to 5.25V)
|
|
|
|
:::tip
|
|
The manufacturer [RaccoonLab Docs](https://docs.raccoonlab.co/guide/autopilot/RCLv6X.html) are the canonical reference for the RaccoonLab FMUv6X Autopilot.
|
|
가장 정확한 최신 정보를 포함하고 있습니다.
|
|
:::
|
|
|
|
## 구매처
|
|
|
|
[RaccoonLab Store](https://raccoonlab.co/store)
|
|
|
|
[Cyphal store](https://cyphal.store)
|
|
|
|
## 펌웨어 빌드
|
|
|
|
:::tip
|
|
Most users will not need to build this firmware!
|
|
It is pre-built and automatically installed by _QGroundControl_ when appropriate hardware is connected.
|
|
:::
|
|
|
|
To [build PX4](../dev_setup/building_px4.md) for this target:
|
|
|
|
```sh
|
|
make px4_fmu-v6x_default
|
|
```
|
|
|
|
## 지원 플랫폼 및 기체
|
|
|
|
일반 RC 서보 또는 Futaba S-Bus 서보로 제어 가능한 모든 멀티콥터/비행기/로버 또는 보트.
|
|
The complete set of supported configurations can be seen in the [Airframes Reference](../airframes/airframe_reference.md).
|
|
|
|
## 추가 정보
|
|
|
|
- [Pixhawk Autopilot FMUv6X Standard](https://github.com/pixhawk/Pixhawk-Standards/blob/master/DS-012%20Pixhawk%20Autopilot%20v6X%20Standard.pdf)
|
|
- [Pixhawk Autopilot Bus Standard](https://github.com/pixhawk/Pixhawk-Standards/blob/master/DS-010%20Pixhawk%20Autopilot%20Bus%20Standard.pdf)
|
|
- [Pixhawk Connector Standard](https://github.com/pixhawk/Pixhawk-Standards/blob/master/DS-009%20Pixhawk%20Connector%20Standard.pdf)
|
|
- [RaccoonLab docs](https://docs.raccoonlab.co/)
|