mirror of
https://gitee.com/mirrors_PX4/PX4-Autopilot.git
synced 2026-04-14 10:07:39 +08:00
178 lines
5.7 KiB
Markdown
178 lines
5.7 KiB
Markdown
# S-Vehicle E2
|
|
|
|
:::warning
|
|
PX4 does not manufacture this (or any) autopilot.
|
|
:::
|
|
|
|
The _E2_ is an advanced autopilot manufactured by S-Vehicle<sup>®</sup>.
|
|
|
|
The autopilot is recommended for commercial system integration, but is also suitable for academic research and any other applications.
|
|
It brings you ultimate performance, stability, and reliability in every aspect.
|
|
|
|
|
|
|
|
:::info
|
|
이 비행 컨트롤러는 [제조업체에서 지원](../flight_controller/autopilot_manufacturer_supported.md)합니다.
|
|
:::
|
|
|
|
### Processors & Sensors
|
|
|
|
- FMU Processor: STM32H753IIK6
|
|
- 32 Bit Arm® Cortex®-M7, 480MHz, 2MB flash memory, 1MB RAM
|
|
- IO Processor: STM32F103
|
|
- 32 Bit Arm® Cortex®-M3, 72MHz, 20KB SRAM
|
|
- 내장 센서 :
|
|
- Accel/Gyro: BMI088
|
|
- Accel/Gyro: ICM-42688-P
|
|
- Accel/Gyro: ICM-20649
|
|
- Mag: RM3100
|
|
- Barometer: 2x ICP-20100
|
|
|
|
### 인터페이스
|
|
|
|
- 14x PWM Servo Outputs
|
|
- 1x Dedicated R/C Input for Spektrum / DSM and S.Bus
|
|
- 1x Analog/PWM RSSI Input
|
|
- 2x TELEM Ports (with full flow control)
|
|
- 1x UART4 Port
|
|
- 2x GPS Ports
|
|
- 1x Full GPS plus Safety Switch Port (GPS1)
|
|
- 1x Basic GPS Port (with I2C, GPS2)
|
|
- 1x USB Port (TYPE-C)
|
|
- 1x Ethernet Port
|
|
- Transformerless application
|
|
- 100Mbps
|
|
- 3x I2C Bus Ports
|
|
- 1x SPI Bus
|
|
- 1x Chip Select Line
|
|
- 1x Data Ready Line
|
|
- 1x SPI Reset Line
|
|
- 2x CAN Ports
|
|
- 3x Power Input Ports
|
|
- ADC Power Input
|
|
- I2C Power Input
|
|
- DroneCAN/UAVCAN Power Input
|
|
- 2x AD Ports
|
|
- Analog Input (3.3V)
|
|
- Analog Input (6.6V - not supported by PX4)
|
|
- 1x Dedicated Debug Port
|
|
- FMU Debug
|
|
|
|
## Purchase Channels {#store}
|
|
|
|
Order from [S-Vehicle](https://svehicle.cn/).
|
|
|
|
## 무선 조종
|
|
|
|
A Radio Control (RC) system is required if you want to manually control your vehicle (PX4 does not require a radio system for autonomous flight modes).
|
|
|
|
기체와 조종자가 통신하기 위하여 송신기와 수신기를 바인딩하여야 합니다.
|
|
송신기와 수신기의 매뉴얼을 참고하십시오.
|
|
|
|
Spektrum/DSM receivers connect to the DSM/SBUS RC input.
|
|
PPM or SBUS receivers connect to the RC IN input port.
|
|
CRSF receiver must be wired to a spare port (UART) on the Flight Controller. Then you can bind the transmitter and receiver together.
|
|
|
|
## 시리얼 포트 매핑
|
|
|
|
| UART | 장치 | 포트 |
|
|
| ------ | ---------- | -------- |
|
|
| USART1 | /dev/ttyS0 | GPS |
|
|
| USART2 | /dev/ttyS1 | TELEM3 |
|
|
| USART3 | /dev/ttyS2 | 디버그 콘솔 |
|
|
| UART4 | /dev/ttyS3 | UART4 |
|
|
| UART5 | /dev/ttyS4 | TELEM2 |
|
|
| USART6 | /dev/ttyS5 | PX4IO/RC |
|
|
| UART7 | /dev/ttyS6 | TELEM1 |
|
|
| UART8 | /dev/ttyS7 | GPS2 |
|
|
|
|
## PWM Output
|
|
|
|
The E2-Plus flight controller supports up to 14 PWM outputs.
|
|
The first 8 outputs (labelled M1 to M8) are controlled by a dedicated STM32F103 IOMCU controller.
|
|
The remaining 6 outputs (labelled 9 to 14) are the "auxiliary" outputs.
|
|
These are directly attached to the STM32H753 FMU controller .
|
|
|
|
The 14 PWM outputs are:
|
|
|
|
M1 - M8 are connected to the IOMCU
|
|
A1 - A6 are connected to the FMU
|
|
|
|
M1 - M8 support DShot and are in 3 groups:
|
|
|
|
- M1, M2 in group 1
|
|
- M3, M4 in group 2
|
|
- M5, M6, M7, M8 in group 3
|
|
|
|
The 6 FMU PWM outputs are in 2 groups:
|
|
|
|
A1 - A4 are in one group.
|
|
A5, A6 are in a 2nd group.
|
|
|
|
Channels within the same group need to use the same output rate.
|
|
If any channel in a group uses DShot then all channels in the group need to use DShot.
|
|
|
|
### Electrical data
|
|
|
|
- Voltage Ratings:
|
|
- Max input voltage: 5.7V
|
|
- USB Power Input: 4.75\~5.25V
|
|
- Servo Rail Input: 0\~9.9V
|
|
- Current Ratings:
|
|
- TELEM1 and GPS2 combined output current limiter: 1.5A
|
|
- All other port combined output current limiter: 1.5A
|
|
|
|
## Battery Monitoring
|
|
|
|
The board has connectors for 3 power monitors.
|
|
|
|
- POWER1 -- ADC
|
|
- POWER2 -- DroneCAN
|
|
- POWER3 -- I2C
|
|
|
|
The board is configure by default for a analog power monitor, and also has DroneCAN power monitor and I2C defaults configured which is enabled.
|
|
|
|
The default PDB included with the E2+ is analog and must be connected to `POWER1`.
|
|
|
|
## 펌웨어 빌드
|
|
|
|
To [build PX4](../dev_setup/building_px4.md) for this target, execute:
|
|
|
|
```sh
|
|
make svehicle_e2_default
|
|
```
|
|
|
|
## 디버그 포트
|
|
|
|
The [PX4 System Console](../debug/system_console.md) and [SWD Interface](../debug/swd_debug.md) operate on the **FMU Debug** port.
|
|
|
|
| 핀 | 신호 | 전압 |
|
|
| ------------------------- | ------------------------------- | --------------------- |
|
|
| 1(red) | 5V+ | +5V |
|
|
| 2 (흑) | DEBUG TX(출력) | +3.3V |
|
|
| 3 (흑) | DEBUG TX(입력) | +3.3V |
|
|
| 4 (흑) | FMU_SWDIO | +3.3V |
|
|
| 5 (흑) | FMU_SWCLK | +3.3V |
|
|
| 6 (흑) | GND | GND |
|
|
|
|
For information about using this port see:
|
|
|
|
- [SWD Debug Port](../debug/swd_debug.md)
|
|
- [PX4 System Console](../debug/system_console.md) (Note, the FMU console maps to USART3).
|
|
- All ports use GH1.25 ,power ports use ports on E2 uses the 6 circuit [2.00mm Pitch CLIK-Mate Wire-to-Board PCB Receptacle](https://www.molex.com/en-us/products/part-detail/5024430670).
|
|
|
|
## 핀배열
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
## 지원 플랫폼 및 기체
|
|
|
|
Any multirotor/airplane/rover or boat that can be controlled using normal RC servos or Futaba S-Bus servos.
|
|
The complete set of supported configurations can be found in the [Airframe Reference](../airframes/airframe_reference.md).
|