mirror of
https://gitee.com/mirrors_PX4/PX4-Autopilot.git
synced 2026-04-14 10:07:39 +08:00
99 lines
4.2 KiB
Markdown
99 lines
4.2 KiB
Markdown
# ARK DIST SR
|
|
|
|
ARK DIST SR is a low range, open source [DroneCAN](index.md) [distance sensor](../sensor/rangefinders.md).
|
|
It has an approximate range of between 8cm to 30m.
|
|
|
|
|
|
|
|
## 구매처
|
|
|
|
Order this module from:
|
|
|
|
- [ARK Electronics](https://arkelectron.com/product/ark-dist-sr/) (US)
|
|
|
|
## Hardware Specifications
|
|
|
|
- [Open Source Schematic and BOM](https://github.com/ARK-Electronics/ARK_DIST)
|
|
- 센서
|
|
- [Broadcom AFBR-S50LV85D Time-of-Flight Distance Sensor](https://www.broadcom.com/products/optical-sensors/time-of-flight-3d-sensors/afbr-s50lv85d)
|
|
- Typical distance range up to 30m
|
|
- Integrated 850 nm laser light source
|
|
- Field-of-View (FoV) of 12.4° x 6.2° with 32 pixels
|
|
- Operation of up to 200k Lux ambient light
|
|
- Reference Pixel for system health monitoring
|
|
- Works well on all surface conditions
|
|
- Transmitter beam of 2° x 2° to illuminate between 1 and 3 pixels
|
|
- Two Pixhawk Standard CAN Connectors (4 Pin JST GH)
|
|
- Pixhawk Standard UART Connector (6 Pin JST SH)
|
|
- Pixhawk Standard Debug Connector (6 Pin JST SH)
|
|
- Small Form Factor
|
|
- 2.0cm x 2.8cm x 1.4cm
|
|
- 4g
|
|
- LED Indicators
|
|
- USA Built
|
|
- NDAA Compliant
|
|
- Power Requirements
|
|
- 5v
|
|
- 84mA Average
|
|
- 86mA Max
|
|
|
|
## 하드웨어 설정
|
|
|
|
### 배선
|
|
|
|
The ARK DIST is connected to the CAN bus using a Pixhawk standard 4 pin JST GH cable.
|
|
For more information, refer to the [CAN Wiring](../can/index.md#wiring) instructions.
|
|
|
|
The ARK DIST can also be connected with UART and communicates over MAVLink sending the [DISTANCE_SENSOR](https://mavlink.io/en/messages/common.html#DISTANCE_SENSOR) message.
|
|
|
|
## Firmware Setup
|
|
|
|
ARK DIST SR runs the [PX4 DroneCAN Firmware](px4_cannode_fw.md).
|
|
As such, it supports firmware update over the CAN bus and [dynamic node allocation](index.md#node-id-allocation).
|
|
|
|
## PX4 설정
|
|
|
|
### DroneCAN
|
|
|
|
#### Enable DroneCAN
|
|
|
|
단계는 다음과 같습니다:
|
|
|
|
- In _QGroundControl_ set the parameter [UAVCAN_ENABLE](../advanced_config/parameter_reference.md#UAVCAN_ENABLE) to `2` for dynamic node allocation (or `3` if using [DroneCAN ESCs](../dronecan/escs.md)) and reboot (see [Finding/Updating Parameters](../advanced_config/parameters.md)).
|
|
- Connect ARK DIST SR CAN to the Pixhawk CAN.
|
|
|
|
Once enabled, the module will be detected on boot.
|
|
Distance sensor data should arrive at 40Hz.
|
|
|
|
DroneCAN configuration in PX4 is explained in more detail in [DroneCAN > Enabling DroneCAN](../dronecan/index.md#enabling-dronecan).
|
|
|
|
#### CAN Configuration
|
|
|
|
First set the parameters to [Enable DroneCAN](#enable-dronecan) (as shown above).
|
|
|
|
Set the following parameters in _QGroundControl_:
|
|
|
|
- Enable [UAVCAN_ENABLE](../advanced_config/parameter_reference.md#UAVCAN_ENABLE) to 2 for dynamic node allocation.
|
|
- Enable [UAVCAN_SUB_RNG](../advanced_config/parameter_reference.md#UAVCAN_SUB_RNG).
|
|
- Set [EKF2_RNG_A_HMAX](../advanced_config/parameter_reference.md#EKF2_RNG_A_HMAX) to `30`.
|
|
- Set [EKF2_RNG_QLTY_T](../advanced_config/parameter_reference.md#EKF2_RNG_QLTY_T) to `0.2`.
|
|
- Set [UAVCAN_RNG_MIN](../advanced_config/parameter_reference.md#UAVCAN_RNG_MIN) to `0.08`.
|
|
- Set [UAVCAN_RNG_MAX](../advanced_config/parameter_reference.md#UAVCAN_RNG_MAX) to `30`.
|
|
|
|
See also [Distance Sensor/Range Finder in _DroneCAN > Subscriptions and Publications_](../dronecan/#distance-sensor-range-finder).
|
|
|
|
### UART/MAVLink Configuration
|
|
|
|
If connecting via a UART set the following parameters in _QGroundControl_:
|
|
|
|
- Set [MAV_X_CONFIG](../advanced_config/parameter_reference.md#MAV_0_CONFIG) to the port the sensor is connected to.
|
|
- Set [MAV_X_FORWARD](../advanced_config/parameter_reference.md#MAV_0_FORWARD) to `0` (off).
|
|
- Set [MAV_X_MODE](../advanced_config/parameter_reference.md#MAV_0_MODE) to `7` or `13` to (Minimal or Low Bandwidth) to reduce memory usage.
|
|
- Set `SER_XXX_BAUD` to `115200`, where `XXX` is specific to the port you are using (such as [SER_GPS2_BAUD](../advanced_config/parameter_reference.md#SER_GPS2_BAUD)).
|
|
- Set [EKF2_RNG_A_HMAX](../advanced_config/parameter_reference.md#EKF2_RNG_A_HMAX) to `30`.
|
|
- Set [EKF2_RNG_QLTY_T](../advanced_config/parameter_reference.md#EKF2_RNG_QLTY_T) to `0.2`.
|
|
|
|
## See Also
|
|
|
|
- [ARK DIST SR](https://docs.arkelectron.com/sensor/ark-dist) (ARK Docs)
|